DIRK BERGMAIER
PRODUCTION D'EXOPOLYSACCHARIDES PAR
FERMENTATION AVEC DES CELLULES
IMMOBILISÉES DE LB. RHAMNOSUS RW-9595M
D'UN MILIEU À BASE DE PERMÉAT DE
LACTOSÉRUM
Thèse
présentée
à la Faculté des études supérieures
de l'Université Laval
pour l’obtention
du grade de Philosophiae Doctor (Ph.D.)
Département des sciences des aliments et de la nutrition
FACULTÉ DES SCIENCES DE L'AGRICULTURE ET DE L'ALIMENTATION
UNIVERSITÉ LAVAL
QUÉBEC
AOÛT, 2002
© Dirk Bergmaier, 2002
Résumé court Une méthode de dosage des EPS basée sur l'ultrafiltration (UF) du milieu fermenté a été mise au point. Cette méthode récupère entre 83 et 104% de l'EPS ajouté d'une solution avec une concentration d'EPS connue (40-1500 mg/l). La production d'EPS a été suivie avec la nouvelle méthode lors de fermentations en batch. La méthode d'UF a été rapide (8h), précise et simple, et a requis seulement un petit volume d'échantillon (1 à 5 ml). Des fermentations dans un milieu de perméat de lactosérum supplémenté (SWP) avec 5 ou 8% (w/w) de perméat de lactosérum un poudre (WP), 1% (w/w) d'extrait de levure, des minéraux et du Tween-80 ont été conduites. Des comptes cellulaires (1.3 · 1010 CFU/ml) et une production d'EPS (2350 mg/l) très élevés ont été obtenus lors de fermentations en batch avec des cellules libres dans le SWP. Une méthode de mesure de la biomasse immobilisée, basée sur l'analyse d'ADN microbien a été mise au point. Cette méthode a dosé une biomasse immobilisée très élevée de 8.5 · 1011 CFU/ml lors des cultures en batch répété avec des cellules immobilisées. Une concentration élevée d'EPS (1808 mg/l) a été mesurée après le quatrième cycle, avec un temps d'incubation très court (7 h) résultant en une productivité volumétrique d'EPS élevée de 258 mg/l h. Lors d'une culture continue avec des cellules libres, une production d'EPS de 1808 mg/l et une productivité volumétrique de 542.6 mg/l·h ont été obtenues pour un taux de dilution (D) de 0.3 h-1. Une fermentation continue avec des cellules immobilisées dans un système à deux étages a été conduite pendant 32 jours. L'influence de la concentration en extrait de levure, de la température et du taux de dilution sur les productions de cellules, d'EPS et d'acide lactique a été étudiée. Un effet significatif (P<0.05) a été trouvé seulement pour la production d'acide lactique mais pas pour la production de biomasse ou d'EPS. Une biomasse immobilisée très élevée et stable, égale à 5.3 ± 1.8 · 1011 CFU/g de support a été mesurée. Un changement physiologique et morphologique de la culture avec une perte de la capacité à produire des EPS solubles (138 mg/l) a été observé, résultant en la formation d'agrégats macroscopiques. Avec le temps, la concentration d'agrégats dans les deux réacteurs a augmenté et les agrégats ont quitté le système par l'effluent avec une productivité volumétrique entre 5.68 et 49.54 g/l·h. Les agrégats contenaient une teneur en biomasse totale de 73.8 % et en EPS non-soluble de 14.2 % (w/w). Un contenu de biomasse viable de 4.32 ± 0.97 · 1012 CFU/g a également été mesuré. Ces agrégats pourraient avoir un grand potentiel d'exploitation comme produit synbiotique, avec des concentrations en cellules actives et en EPS très élevées.
_______________________ ________________________ Dirk Bergmaier Christophe Lacroix Directeur de recherche
iv
Abstract A new method for EPS quantification based on ultrafiltration (UF) of fermented broth was developed. This method recovered between 83 and 104% of EPS in a solution with known concentration (40-1500 mg/l). The EPS production during batch fermentations was followed using the new method. The UF method was fast (8 h), accurate and simple, and required only small sample volumes (1 to 5 ml). Cultures were conducted in a supplemented whey permeate (SWP) medium containing 5 or 8% (w/w) whey permeate, 1% (w/w) yeast extract, minerals and Tween-80. Very high cell counts (1.3 · 1010 CFU/ml) and EPS productions (2350 mg/l) were obtained during batch fermentations with free cells. The cells were immobilized on solid supports and a method for immobilized biomass quantification, based on DNA analysis, was developed. This method measured a very high immobilized biomass of 8.5 · 1011 CFU/ml of support during repeated batch cultures. A high EPS concentration (1808 mg/l) was measured after the fourth cycle, with a very short incubation time (7 h) resulting in a high EPS volumetric productivity of 258 mg/l h. During continuous culture with free cells, an EPS production of 1808 mg/l and a volumetric productivity of 542.6 mg/l h was obtained for a dilution ratio (D) of 0.3 h-1. A 32-day continuous fermentation with cells immobilized in a two-stage bioreactor system was conducted. The influence of yeast extract concentration, temperature and dilution rate on the production of biomass, EPS and lactic acid was studied. A significant effect (P<0.05) was found only for lactic acid but not for biomass or EPS production. A very high and stable immobilized biomass equal to 5.3 ± 1.8 · 1011 CFU/g support was measured. A physiological and morphological change of the culture with the loss of the capacity to produce soluble EPS (138 mg/l) was observed, resulting in the formation of macroscopic aggregates. With time, the aggregate concentration in the two reactors increased and the aggregates left the system in the effluent with a volumetric productivity between 5.68 and 49.54 g/l h. The aggregates contained 73.8% total biomass and 14.2% insoluble EPS (w/w). A viable biomass content of 4.32 ± 0.97 · 1012 CFU/g was also measured. These aggregates could find applications as synbiotic food-ingredients with very high active cell and EPS concentrations.
_______________________ ________________________ Dirk Bergmaier Christophe Lacroix Directeur de recherche
v
Résumé long Le but de cette thèse a été de développer un procédé d'immobilisation cellulaire et de l'exploiter afin de produire des exopolysaccharides lors de fermentations d'un milieu à base de perméat de lactosérum par Lactobacillus rhamnosus RW-9595M. Des fermentations en continu avec des cellules immobilisées sur des supports poreux solides en caoutchouc de silicone (ImmobaSil®) ont été comparées avec des fermentations avec des cellules planctoniques. Différentes stratégies (cultures en batch, à cycles répétés et continue) de fermentation avec cellules libres ou immobilisées ont été testées pour la production d'EPS.
Tout d'abord, une nouvelle méthode de dosage d'EPS a été mise au point. Cette méthode utilise l'ultrafiltration dans des cellules agitées pour l'élimination des hydrates de carbone simples du milieu de culture. Ensuite, les exopolysaccharides (EPS) restant dans le rétentat sont dosés par la méthode phénol-sulfurique. La production d'EPS pendant des fermentations en batch dans divers milieux de culture (milieu défini BMM, perméat de lactosérum et perméat de lactosérum supplémenté) a été déterminée par la nouvelle méthode UF et par une méthode conventionnelle. Le taux de récupération des EPS ajoutés à une solution de 0.1 M NaCl ou à des échantillons de milieu de culture par la nouvelle méthode s'est situé entre 83 et 104% pour une concentration d'EPS entre 40 et 1500 mg/l. La méthode d'UF est rapide (8 h), précise et simple, et ne requiert qu'un petit volume d'échantillon (1 à 5 ml). Lors des fermentations à pH 6 et 37°C du perméat de lactosérum supplémenté avec de l'extrait de levure, des minéraux et de Tween-80 (SWP), une production maximale d'EPS très élevée a été mesurée par les méthodes UF et conventionnelle (1718 et 1755 mg/l).
Par la suite, d'autres cultures en batch à pH contrôlé ont été réalisées avec des cellules libres, et comparées avec des cultures en batch à cycles répétés avec des cellules immobilisées. Les cellules ont été immobilisées par adsorption sur des supports poreux solides en caoutchouc de silicone (ImmobaSil®). Les cultures ont été conduites à un pH de 6 et à 37°C dans le SWP, contenant du perméat de lactosérum à une concentration de 5% ou de 8% (w/w). Pour des cultures en batch avec cellules libres dans le milieu SWP à 8%, des comptes cellulaires (1.3 · 1010 CFU/ml) et une production d'EPS (2350 mg/l) très élevés ont été mesurés. Plusieurs méthodes de mesure de la biomasse immobilisée, basées sur l'analyse des composants de la biomasse (protéines, ATP et ADN) ont été examinées. La méthode d'analyse d'ADN s'est avérée la plus appropriée dans les conditions testées. Cette méthode a dosé une biomasse immobilisée très élevée de 8.5 · 1011 CFU/ml après la colonisation des supports ImmobaSil®. Pendant les cultures répétées avec des cellules immobilisées dans le milieu SWP à 5%, une concentration élevée d'EPS (1808 mg/l) a été mesurée après le quatrième cycle, avec un temps d'incubation très court (7 h). La biomasse élevée dans le système à cellules immobilisées a augmenté la productivité volumétrique
vi
maximale d'EPS (258 mg/l · h après 7 h) en comparaison avec les cultures en batch avec des cellules libres (110 mg/l · h après 18 h).
Une culture continue avec les cellules libres a été conduite pendant 9 jours à des taux de dilution (D) entre 0.3 et 0.8 h-1. Une production d'EPS (1808 mg/l) et une productivité volumétrique maximales (542.6 mg/l·h) élevées ont été obtenues pour un bas D de 0.3 h-1, tandis que la productivité spécifique en EPS était maximale (9.80 ± 1.01 · 10-11 mg/CFU · h) pour un D intermédiaire de 0.7 h-1. Ensuite, une fermentation continue dans un système de bioréacteurs à deux étages a été conduite pendant 32 jours. Le fermenteur du premier étage contenait des cellules immobilisées par adsorption sur des supports ImmobaSil®. Le deuxième étage de fermentation en série était constamment inoculé par les cellules produits dans le premier étage. L'influence de la concentration en extrait de levure, de la température et du taux de dilution sur les productions de cellules, d'EPS et d'acide lactique dans le milieu a été étudiée, en utilisant un plan central composite rotatif avec une analyse de surface de réponse. Un modèle statistiquement significatif (P<0.05) a été trouvé seulement pour la production d'acide lactique mais pas pour la production de biomasse ou d'EPS. Des concentrations moyennes de cellules libres de 1.36 · 109 CFU/ml et de 2.26 · 109 CFU/ml ont été déterminées dans le premier et le deuxième réacteur, respectivement. Une biomasse immobilisée très élevée et stable, égale à 5.3 ± 1.8 · 1011 CFU/g de support, a été mesurée par la méthode de dosage d'ADN. En dépit de ces concentrations élevées en cellules libres et immobilisées, la production moyenne d'EPS soluble a été très basse (138 mg/l). Ce résultat peut être expliqué par des changements morphologiques et physiologiques majeurs de Lb. rhamnosus RW-9595M qui conduisent, après dix jours de fermentation, à la formation d'agrégats de forte taille (1-2 millimètres), contenant des cellules. La perte de la capacité des cellules à produire des EPS solubles, observée dans le système à cellules immobilisées, était réversible et la production d'EPS a été entièrement récupérée après quatre cultures successives en batch à pH contrôlé.
Afin de mieux caractériser les changements physiologiques de la souche lors des fermentations continues avec cellules immobilisées, les agrégats ont été quantifiés et leur composition analysée. Avec le temps, les agrégats se sont accumulés dans le premier et dans le deuxième réacteur et ont atteint des concentrations moyennes respectives de 33.9 et 54.8 g/l, lors des 5 derniers jours de la fermentation. La concentration d'agrégats dans l'effluent du système à deux étages a varié entre 3.16 et 28.59 g/l selon les conditions et le temps de la fermentation, résultant en une productivité volumétrique d'agrégats entre 5.68 et 49.54 g/l · h. L'analyse chimique des agrégats a indiqué une teneur élevée en azote de 10.1 ± 0.1 % (w/w), ce qui correspond à une biomasse totale de 73.8 % du poids sec de l'agrégat. La teneur élevée des agrégats en polysaccharides (14.2 ± 1.6 %) a été attribuée à la production d'un EPS non-soluble par la culture immobilisée. Une biomasse viable extrêmement élevée et relativement stable dans les agrégats de 4.32 · 1012 ± 0.97 · 1012 CFU/g a également été mesurée par la méthode d'extraction d'ADN. Les
vii
agrégats produits pendant la culture en continu avec des cellules immobilisées dans un milieu de perméat de lactosérum supplémenté, peuvent être facilement séparés et pourraient avoir un grand potentiel d'exploitation comme produit synbiotique, avec des concentrations en cellules actives et en EPS très élevées.
_______________________ ________________________ Dirk Bergmaier Christophe Lacroix Directeur de recherche
Avant-propos Le corps de cette thèse est composé de cinq chapitres. Le premier chapitre, intitulé "Revue
de littérature", donne une vue d'ensemble des connaissances actuelles sur les
exopolysaccharides en général et les hétéropolysaccharides des bactéries lactiques en
particulier. Dans ce même chapitre, l'immobilisation cellulaire est également introduite et
une vue d'ensemble des techniques et des effets de l'immobilisation sur la culture
immobilisée est donnée. Les références bibliographiques des chapitres sont présentées à la
fin de la thèse.
Les chapitres suivants sont présentés sous forme d'articles scientifiques. Le travail rapporté
dans le chapitre 2, intitulé "New Method for Exopolysaccharide Determination in Culture
Broth using Stirred Ultrafiltration Cells", a permis de réaliser le premier objectif spécifique
de mon projet de doctorat: développer une méthode précise et rapide de mesure des EPS
produits dans le milieu de fermentation. Les résultats de ce travail ont été publiés dans le
journal "Applied Microbiology and Biotechnology". J'ai planifié l'ensemble des
expérimentations et je suis l'auteur principal de cette publication. J'ai exécuté les
fermentations dans le milieu à base de perméat de lactosérum et les expériences
d'ultrafiltration. J'ai bénéficié de l'aide de Maria Guadalupe Macedo qui a exécuté les
fermentations dans le milieu BMM et a mis à ma disposition les milieux fermentés.
Le chapitre 3 expose une comparaison des résultats obtenus lors des fermentations en batch
avec des cellules libres et des cellules immobilisées de Lb. rhamnosus RW-9595M. Une
méthode de dosage de la biomasse immobilisée sur des supports libres y est aussi présentée.
Ce chapitre a été soumis pour publication dans le "Journal of Biotechnology". Je suis
l'auteur principal de cette publication et j'ai effectué l'ensemble des expérimentations.
L'article qui fait objet du chapitre 4 traite des fermentations en continu avec des cellules
libres et immobilisées de Lb. rhamnosus RW-9595M. Dans ce chapitre, l'effet de différents
paramètres (concentration en extrait de levure, température et taux de dilution) sur la
production d'EPS, d'acide lactique et de biomasse dans un système de fermentation en deux
étapes avec des cellules immobilisées est décrite. Le chapitre 5 examine de plus près un
iv
phénomène observé lors de cette fermentation, soit la formation d'agrégats macroscopiques.
Les résultats correspondants aux chapitres 4 et 5 ont été soumis pour publication dans
"Biotechnology Progress". Je suis auteur principal de ces publications et j'ai effectué
l'ensemble des expérimentations.
Ensemble avec les résultats d'un collègue, Yann Doleyres, les observations lors de ces
expériences et ont conduit au dépôt d'un brevet provisoire intitulé " Control and modulation
of probiotic culture characteristics with immobilized cell technology". Finalement, une
conclusion générale intègre les résultats les plus importants de ce projet et présente une
vision globale et les perspectives pour des travaux futurs.
Remerciements Cette thèse représente quatre années de travail, durant lesquelles l'appui et l'aide de
nombreuses personnes ont été essentiels.
A mon directeur, Christophe Lacroix, j'adresse ma reconnaissance pour ces conseils
scientifiques judicieux, sa disponibilité exceptionnelle, son appui financier et la liberté
d'action qu'il m'a laissée tout au long de ce projet. Je remercie également mon codirecteur,
Claude Champagne, pour ces suggestions pertinentes et son aide dans la rédaction des
articles.
Mes remerciements également au personnel et à mes collègues du Centre STELA ainsi qu'à
ceux des laboratoires du département ALN et des laboratoires de microscopie électronique
qui par leur appui technique et leurs conseils, ont contribué à la réalisation de ce travail. Je
pense plus particulièrement à Maria Guadalupe Macedo, Céline Paquin, Bernard Béliveau,
Jocelyne Giasson, Alain Gaudreau, Hélène Chamberland et Aristide Pusterla.
Je désire remercier le Conseil de Recherches en Sciences Naturelles et en Génie du Canada
(Programme de partenariats de recherche – Réseau de recherche sur les Bactéries
Lactiques), Agriculture et Agroalimentaire Canada, Novalait inc., les Producteurs laitiers
du Canada et l'Institut Rosell–Lallemand Inc. pour leur support financier.
Enfin, ce travail est l'aboutissement de longues années d'étude, auxquelles l'amour et le
soutien de ma famille en Allemagne ainsi qu'à Québec ont largement contribué. À ma
conjointe, Sophie, je voudrais rappeler mon amour et ma reconnaissance pour sa
compréhension, sa présence affectueuse à mes côtés et le plus beau cadeau de ma vie, notre
fils Victor.
Für meine Großeltern, Eltern und Schwester,
deren Nähe mir oft fehlte,
meine Familie in Québec,
die mich mit offenen Armen empfang,
Sophie und Victor,
die ich von Herzen liebe.
Table des matières Résumé court ....................................................................................................................... iii
Abstract................................................................................................................................ iv
Résumé long.......................................................................................................................... v
Avant-propos ....................................................................................................................... iii
Remerciements ..................................................................................................................... v
Introduction générale .......................................................................................................... 1
Chapitre 1 Revue de littérature...................................................................................... 2
1.1 Exopolysaccharides d'origine microbienne............................................................ 2
1.1.1 Fonction pour la souche productrice .............................................................. 3
1.1.2 Utilisations et applications industrielles......................................................... 5
1.2 Exopolysaccharides des bactéries lactiques ........................................................... 7
1.2.1 Composition et structure ................................................................................ 8
1.2.2 Fonctionnalité des hétéropolysaccharides...................................................... 9
1.2.2.1 Fonctionnalité technologique ..................................................................... 9
1.2.2.2 Fonctionnalité physiologique ................................................................... 10
1.2.3 Biosynthèse des hétéropolysaccharides des bactéries lactiques................... 13
1.2.4 Génétique de la production des hétéropolysaccharides ............................... 17
1.2.5 Production des hétéropolysaccharides par les bactéries lactiques ............... 19
1.2.5.1 Milieux utilisés pour la production d'EPS................................................ 20
1.2.5.2 Rendement de la production d'EPS.......................................................... 20
1.2.5.3 Effet du milieu de culture sur la production............................................. 23
1.2.5.3.1 Source d'azote .................................................................................... 23
1.2.5.3.2 Source de carbone .............................................................................. 24
1.2.5.3.3 Minéraux et vitamines........................................................................ 25
1.2.5.4 Effet du milieu sur la composition de l'EPS ............................................ 25
1.2.5.5 Cinétique de la production des EPS par les bactéries lactiques ............... 26
1.2.5.6 Effets des conditions de culture ............................................................... 27
1.2.6 Méthodes d'analyse des EPS ........................................................................ 29
1.2.6.1 Quantification........................................................................................... 29
viii
1.2.6.2 Caractérisation physico-chimique............................................................ 32
1.2.6.3 Production à grande échelle et traitement en aval.................................... 33
1.2.7 Utilisation et applications des hétéropolysaccharides.................................. 34
1.3 Technologie des cellules immobilisées................................................................ 35
1.3.1 Techniques et procédures d'immobilisation................................................. 37
1.3.2 Choix du support .......................................................................................... 40
1.3.3 Analyse des cellules immobilisées............................................................... 42
1.3.4 Effets physiologiques et morphologiques de l'immobilisation .................... 44
1.4 Problématique ...................................................................................................... 45
1.5 Hypothèse et objectifs de travail .......................................................................... 46
1.5.1 Objectif général............................................................................................ 47
1.5.2 Objectifs spécifiques .................................................................................... 47
Chapitre 2 New method for exopolysaccharide determination in culture broth
using stirred ultrafiltration cells ....................................................................................... 48
2.1 Résumé................................................................................................................. 49
2.2 Abstract ................................................................................................................ 49
2.3 Introduction.......................................................................................................... 50
2.4 Materials and methods ......................................................................................... 51
2.4.1 Microorganism ............................................................................................. 51
2.4.2 Culture media ............................................................................................... 51
2.4.3 Fermentations............................................................................................... 51
2.4.4 Cell enumeration .......................................................................................... 52
2.4.5 EPS purification and quantification by the conventional method................ 52
2.4.6 EPS purification and quantification using stirred ultrafiltration cells.......... 53
2.4.7 Validation of the ultrafiltration method for EPS analysis............................ 54
2.4.8 Sugar and lactic acid analysis ...................................................................... 55
2.4.9 Statistics ....................................................................................................... 55
2.5 Results .................................................................................................................. 56
2.5.1 Characterization of the UF method .............................................................. 56
2.5.2 EPS quantification during batch cultures..................................................... 57
2.6 Discussion ............................................................................................................ 60
ix
2.7 Conclusions.......................................................................................................... 64
Chapitre 3 Exopolysaccharide production during batch cultures with free and
immobilized Lactobacillus rhamnosus RW-9595M......................................................... 65
3.1 Résumé................................................................................................................. 66
3.2 Abstract ................................................................................................................ 66
3.3 Introduction.......................................................................................................... 67
3.4 Materials and Methods......................................................................................... 69
3.4.1 Strain and culture media............................................................................... 69
3.4.2 Fermentation techniques .............................................................................. 69
3.4.3 Cell enumeration and biomass determination .............................................. 70
3.4.4 Immobilized biomass determinations .......................................................... 70
3.4.4.1 DNA extraction ........................................................................................ 70
3.4.4.2 ATP extraction ......................................................................................... 72
3.4.4.3 Protein extraction ..................................................................................... 72
3.4.5 EPS concentration analysis .......................................................................... 73
3.4.6 Sugar and organic acid analysis ................................................................... 73
3.5 Results and Discussion......................................................................................... 73
3.5.1 Cell and EPS production during free-cell batch cultures ............................. 74
3.5.2 Cell production during repeated batch cultures with immobilized cells...... 76
3.5.3 Immobilized cell concentration in the solid supports .................................. 77
3.5.4 EPS production during repeated batch cultures with immobilized cells...... 81
3.6 Conclusions.......................................................................................................... 82
Chapitre 4 Exopolysaccharide production during chemostat cultures with free and
immobilized Lactobacillus rhamnosus RW-9595M......................................................... 83
4.1 Résumé................................................................................................................. 84
4.2 Abstract ................................................................................................................ 85
4.3 Introduction.......................................................................................................... 85
4.4 Material and Methods .......................................................................................... 87
4.4.1 Microorganism ............................................................................................. 87
4.4.2 Culture media ............................................................................................... 88
4.4.3 Fermentation techniques .............................................................................. 88
x
4.4.3.1 Free-cell continuous culture..................................................................... 88
4.4.3.2 Immobilized-cell continuous culture........................................................ 89
4.4.3.3 Successive free-cell batch cultures........................................................... 90
4.4.4 Cell enumeration and biomass determination .............................................. 90
4.4.5 Determination of immobilized biomass concentration in solid supports..... 91
4.4.6 EPS concentration analysis .......................................................................... 91
4.4.7 Sugar and organic acid analysis ................................................................... 91
4.4.8 Microscopy observations ............................................................................. 91
4.4.9 Experimental design and statistical analysis ................................................ 92
4.5 Results .................................................................................................................. 93
4.5.1 Free-cell chemostat cultures......................................................................... 93
4.5.2 Immobilized-cell chemostat cultures ........................................................... 94
4.5.2.1 Free and immobilized biomass production .............................................. 95
4.5.2.2 Sugar and product concentration.............................................................. 97
4.5.3 Successive batch fermentations with cells from immobilized cell culture 101
4.6 Discussion .......................................................................................................... 101
4.7 Conclusions........................................................................................................ 107
Chapitre 5 Aggregate formation during chemostat culture with immobilized
Lactobacillus rhamnosus RW-9595M ............................................................................. 109
5.1 Résumé............................................................................................................... 110
5.2 Abstract .............................................................................................................. 110
5.3 Introduction........................................................................................................ 111
5.4 Material and Methods ........................................................................................ 112
5.4.1 Microorganism and culture conditions ...................................................... 112
5.4.2 Biomass concentration determinations ...................................................... 113
5.4.3 Microscopy observations ........................................................................... 114
5.4.4 Aggregate dry weight determination.......................................................... 114
5.4.5 Chemical analysis of aggregates ................................................................ 115
5.4.6 Experimental design and statistic analysis................................................. 115
5.5 Results ................................................................................................................ 116
5.5.1 Microscopical and macroscopical observations......................................... 116
xi
5.5.2 Aggregate production................................................................................. 119
5.5.3 Aggregate composition .............................................................................. 120
5.6 Discussion .......................................................................................................... 122
5.7 Conclusions........................................................................................................ 126
Conclusion générale ......................................................................................................... 127
Bibliographie .................................................................................................................... 130
Annexe 1 Concentration en ATP pendant une fermentation avec des cellules libres de
Lb. rhamnosus RW-9595M.............................................................................................. 150
Annexe 2 Cell counts and lactic acid, soluble EPS and immobilized cell concentration
during a 32 day continuous culture in a two stage bioreactor system. ....................... 151
Annexe 3 Analysis of variance and parameter estimates for lactic acid concentration
in the effluent of the ICB and the FCB. ......................................................................... 152
Liste des tableaux Tab. 1.1 Production d'EPS par les LAB............................................................................... 22
Tab. 1.2 Avantages et désavantages de la technologie des cellules immobilisées. ............. 37
Tab. 1.3 Immobilisation par inclusion dans des supports solides poreux............................ 41
Tab. 2.1 EPS concentration and recovery rate (R) determined by the UF method for 0.1 M
NaCl and 5% WP solutions spiked with EPS. ............................................................. 57
Tab. 4.1 Real and coded values of the central composite experimental design for the
continuous immobilized cell fermentation................................................................... 95
Liste des figures Fig. 1.1 Structure du dextrane, un homopolymère................................................................. 8
Fig. 1.2 Structure de l'EPS de Lb. rhamnosus RW-9595M (Van Calsteren et al. 2002). ...... 9
Fig. 1.3 Schéma des voies métaboliques impliquées dans le catabolisme du
lactose/galactose et la biosynthèse des EPS par Lactococcus lactis Gal+ (via les
systèmes phosphoénolpyruvate PEP et phospho-transférase PTS) et par Lactobacillus
delbrueckii ssp. bulgaricus et Streptococcus thermophilus Gal- (via l'antiport
lactose/galactose) (De Vuyst et al. 2001). ................................................................... 15
Fig. 1.4 Modèle de la biosynthèse d'EPS par Lactococcus lactis ssp. lactis NIZO B40 (Van
Kranenburg et al. 1998) ............................................................................................... 16
Fig. 1.5 Organisation des gènes codant pour la production d'EPS chez Lactococcus lactis
NIZO B40 (plasmidique) et chez Streptococcus thermophilus Sfi6 (adapté de De
Vuyst et al., 2001)........................................................................................................ 19
Fig. 1.6 Classification des systèmes d’immobilisation selon quatre classes (adapté de
Willaert et Baron 1996)................................................................................................ 38
Fig. 2.1 Schematic diagram of the laboratory device used for ultrafiltration experiments in
stirred cells. .................................................................................................................. 54
Fig. 2.2 Change in viable cell count ( ), lactose ( ) and lactic acid ( ) concentrations,
and EPS production measured by the UF ( ) and conventional ( ) methods during
pH-controlled batch cultures with Lb. rhamnosus RW-9595M in BMM. Means and
standard deviations for three fermentations. ................................................................ 58
Fig. 2.3 Change in viable cell count ( ), volume of base consumed (―), and EPS
production measured by the UF ( ) and conventional ( ) methods during a pH-
controlled batch culture with Lb. rhamnosus RW-9595M in WP. Means and standard
deviations for duplicate analyses by the UF method. .................................................. 59
Fig. 2.4 Change in viable cell count ( ), lactose ( ) and lactic acid ( ) concentrations,
and EPS production measured by the UF ( ) and conventional ( ) methods during
pH-controlled batch cultures with Lb. rhamnosus RW-9595M in SWP. Means and
standard deviations for three fermentations. ................................................................ 60
xiv
Fig. 3.1 Viable cell counts (●), lactose (■) and lactic acid (♦) concentrations, and EPS
production (▲) during pH-controlled batch cultures with Lb. rhamnosus RW-9595M.
Means and standard deviations for two fermentations................................................. 75
Fig. 3.2 Free-cell counts (●), immobilized cell concentration measured by DNA extraction
method (■) and polysaccharide concentration in the broth (vertical bars) during four
repeated batch cultures with Lb. rhamnosus RW-9595M immobilized on ImmobaSil®
silicone rubber solid supports. ..................................................................................... 77
Fig. 4.1 Viable cell counts (vertical bars), EPS concentration (●), and EPS volumetric (■)
and specific productivities (▲) during free-cell chemostat culture with Lb. rhamnosus
RW9595M for different dilution rates. Means and standard deviations for two
replications of D........................................................................................................... 94
Fig. 4.2 Optical micrograph (10X) of a semi-fine slice (methylene blue staining) of the
ImmobaSil® support colonized with Lb. rhamnosus RW-9595M after 7 day chemostat
culture........................................................................................................................... 96
Fig. 4.3 Photomicrograph of Lb. rhamnosus RW-9595M: a) in the FCB effluent after
14 days of chemostat culture (63X) b) in the fermented medium at the end of a free-
cell batch culture (100X).............................................................................................. 97
Fig. 4.4 Response surface of lactic acid concentration in the first immobilized-cell
bioreactor (ICB) for T = 34°C, covariates stop = 0.5 and age = 12 days. ................... 99
Fig. 4.5 Response surface of lactic acid concentration in the second free-cell bioreactor
(FCB) for T = 34°C, covariates stop = 0.5 and age = 12 days................................... 100
Fig. 5.1 Scanning electron microscopy of colonized ImmobaSil® supports: a) pore at the
surface (magnification 1600 X, b) and c) inner pores (magnification 3600 X and
12000 X, respectively). .............................................................................................. 118
Fig. 5.2 Optical microscopy observations of semi-fine slices of aggregates stained with
methylene blue: a) high cell density (20 X), b) and c) formation of channels (63 X).
.................................................................................................................................... 118
Fig. 5.3 Scanning electron microscopy of a cut through the aggregate: a) at a magnification
of 11000 X, b) at a magnification of 7800 X with crystal. ........................................ 119
Fig. 5.4 Change of aggregate dry weight in the fermented broth in the first ICB (solid bars)
and the second FCB (dashed bars) bioreactors as a measure of aggregate accumulation
xv
during the 32-day continuous culture. Age 1 day corresponds to the start of the
experimental design after an 8-day initial stabilization period. Fermentation conditions
were changed every day according to the central composite rotatable design. ......... 121
Fig. 5.5 Change of aggregate dry weight in effluent samples (solid bars) and volumetric
productivity of the two-stage continuous culture (dashed bars) during the 32-day
experiment. Age 1 day corresponds to the start of the experimental design after an 8-
day initial stabilization period. Fermentation conditions were changed every day
according to the central composite rotatable design. ................................................. 121
Introduction générale Dans le domaine agroalimentaire, l’utilisation des polysaccharides est très courante. Leur
propriétés rhéologiques les rendent capables d’épaissir, de gélifier, de stabiliser et
d’émulsifier. Ils sont souvent utilisés pour diminuer l’activité de l’eau de l’aliment et
contribuent ainsi à la conservation. Appartenant à la classe des fibres alimentaires, ils
servent aussi à remplacer le gras. Ils peuvent non seulement améliorer les comportements
organoleptiques, mais ils pourraient permettre également de produire des aliments
possédant des propriétés nutraceutiques (immunomodulatrices, antivirales, anti-tumorales,
amélioration du transit digestif). Plusieurs bactéries lactiques synthétisent et excrètent des
polysaccharides qui peuvent être utilisés comme bioingrédients fonctionnels permettant de
remplacer d’autres agents polysaccharidiques tels que les carraghénanes, les alginates ou la
gélatine. Ainsi, à l’aide de ces bactéries, il est possible de fabriquer des produits laitiers
fermentés avec un comportement rhéologique amélioré et en même temps de répondre à
une forte demande des consommateurs pour des produits naturels sans additifs. Cependant,
on constate que les bactéries lactiques ont une faible production de polysaccharides et un
caractère épaississant extrêmement instable, ce qui représente un inconvénient majeur pour
l’exploitation en industrie laitière.
Pour remédier à ces problèmes, la technique d’immobilisation représente une bonne
solution. L'utilisation de l'immobilisation cellulaire avec des bactéries lactiques augmente
largement la concentration en biomasse dans le fermenteur. Avec l'immobilisation
cellulaire couplée avec une fermentation en batch-répété ou en continu, on peut obtenir un
rendement et une stabilité des cellules plus élevés qu'avec des cellules libres. Pendant la
fermentation, les cellules sont protégées des forces de cisaillement et elles peuvent être
récupérées et réutilisées. Plusieurs procédés d’immobilisation ont été développés au cours
des vingt dernières années. Souvent, le procédé imite ce qui se produit dans la nature où la
majorité des cellules microbiennes vivent sous forme de biofilm. L'immobilisation par
adsorption sur des supports solides préformés est une technique d'immobilisation qui
pourrait être très appropriée pour les bactéries lactiques productrices d'exopolysaccharides,
car le caractère mucoïde de ces souches favoriserait l'adhésion des cellules au support et
faciliterait ainsi sa colonisation.
Chapitre 1
Revue de littérature
1.1 Exopolysaccharides d'origine microbienne
La plupart des microorganismes synthétisent plusieurs types de polysaccharides qui
peuvent être classés selon leur localisation dans la cellule. Certains se trouvent à l’intérieur
de la cellule, dans le cytoplasme, où ils sont utilisés par la bactérie comme source
d’énergie. D'autres sont des composants de la paroi tels que les peptidoglycanes et les
acides téichoïques. Enfin, un troisième groupe de polysaccharides est excrété à l'extérieur
de la cellule. Le terme "exopolysaccharide" (EPS) ou "polysaccharide exocellulaire" a été
proposé par Sutherland (1972) et Cerning (1994) comme appellation générale pour ce
groupe. Les microorganismes peuvent excréter deux types d'EPS. Le polysaccharide peut
soit être excrété dans le milieu environnant, soit rester lié à la surface de la cellule sous
forme de capsule.
Les exopolysaccharides sont impliqués dans des phénomènes aussi différents que
l'adhésion de Staphylococcus epidermidis à des implants biomédicaux sous-cutanés (Dunne
2002), le colmatage des pipelines et des échangeurs de chaleur, ainsi que la formation de la
plaque dentaire (De Vuyst et Degeest 1999b). La grande diversité structurale des
polysaccharides microbiens témoigne de l'adaptation des microorganismes à des
environnements très différents.
Selon leur composition chimique, les EPS peuvent être subdivisés en deux groupes: les
homopolysaccharides et les hétéropolysaccharides. Tandis que les homopolysaccharides
sont constitués d'un seul type de monomère saccharidique, les hétéropolysaccharides
peuvent contenir plusieurs types de sucres. Parmi les homopolysaccharides, on retrouve les
α-glucanes généralement composés des résidus de glucose liés en α-1,6 et α-1,3; comme les
dextranes produits par Leuconostoc mesenteroides et les glucanes par Streptococcus mutans
et Streptococcus sobrinus. Les levanes, synthétisés de Streptococcus salivarius, sont aussi
des homopolysaccharides, constitués de résidus de fructose liés en β-2,6. Le groupe d'EPS
3
le plus large et le plus diversifié est le groupe des hétéropolysaccharides qui se composent
de plusieurs types d'oses constitutifs. Les hétéropolysaccharides sont formés d'unités
répétitives, variables dans leur taille (de di- à octasaccharides), mais aussi d'autres groupes
peuvent être présents, tels des groupements phosphate, amino ou acétyle. La production
d'hétéropolysaccharides est très fréquente parmi les microorganismes et on y trouve aussi
bien des souches d'un intérêt médical comme Escherichia coli, Salmonella spp. ou
Enterobacter spp. que des bactéries lactiques.
1.1.1 Fonction pour la souche productrice
Des bactéries productrices d'EPS ont été identifiées dans une gamme de niches écologiques
différentes et il est évident que le rôle joué par l'EPS dépend de l'environnement du
microorganisme. Il a été proposé que la capacité de production d'EPS constitue une réponse
directe et logique aux pressions sélectives de l'environnement (Dudman 1977).
L'anabolisme d'EPS demande beaucoup d'énergie, il est donc improbable qu'une bactérie
utilise autant d'énergie et de substrat sans en tirer un avantage. L’importance des EPS pour
la cellule ne semble pas être très grande si on considère les bactéries in vitro. Par contre,
sous des conditions naturelles, ce qui signifie des conditions fortement concurrentielles, les
EPS semblent donner aux bactéries un avantage compétitif et leur permettre de se maintenir
(Cerning 1994). La prolifération des microorganismes ne semble pas être affectée par la
présence où l’absence d’une capsule. L'enlèvement mécanique ou enzymatique de la
capsule polysaccharidique n'affecte pas négativement la croissance cellulaire in vitro et des
mutants non-producteurs d'EPS peuvent apparaître spontanément. En général, les bactéries
productrices d’EPS ne sont pas capables de cataboliser les EPS qu’elles ont produits. Ainsi,
les EPS ne semblent pas jouer le rôle d’une source d’énergie quoique dans certains cas, une
dégradation du polymère a été observée (Cerning 1994).
Le rôle des EPS pour la cellule le plus souvent proposé est de nature protectrice vis à vis de
son environnement. La capacité de s'enrober dans une couche d'EPS avec un forte teneur en
eau la rend plus résistante à la dessiccation et à la déprédation des protozoaires. La nature
anionique de la couche d'EPS autour de la cellule peut aider à capturer des minéraux
4
essentiels et des nutriments. Ainsi, un rôle écologique de l'EPS des cyanobactéries semble
être le recyclage des métaux multivalents comme le Mn2+.
De plus, une couche d'EPS autour de la cellule influence significativement la diffusion de
différentes molécules aussi bien vers l'extérieur ou vers l'intérieur de la cellule. Ainsi, des
agents anti-microbiens peuvent plus difficilement l'atteindre (Whitfield 1988). La
production d'EPS a conféré à une souche de Lactococcus lactis une tolérance augmentée
envers le cuivre, la nisine et le lysozyme (Looijesteijn et al. 2001). Une autre fonction des
EPS pourrait être de protéger les cellules contre la phagocytose. Il semble qu’il existe une
relation entre l’encapsulation de la bactérie et les phénomènes de virulence. En augmentant
l’hydrophobicité de la surface bactérienne, la capsule diminue sa disposition à être absorbée
par les neutrophiles.
Dans la littérature, il existe des données contradictoires en ce qui concerne la relation entre
les EPS et la résistance phagique. Bien qu’il semble que la capsule ait la fonction de
protéger la cellule, les bactériophages actifs sur les souches encapsulées sont généralement
spécifiques pour les polysaccharides de la capsule. Valyasevi et al. (1994) ont montré que
les polysaccharides de la paroi des souches de L. cremoris KH et L. lactis C2 favorisent
l'adsorption des bactériophages Kh et sK1, respectivement. D'autre part, la production d'un
EPS capsulaire confère à L. lactis MG1614 contenant le plasmide pNZ4030 codant pour la
production d'EPS une résistance accrue envers le bactériophage ML3 (Looijesteijn et al.
2001).
Dans l'environnement naturel, les micro-organismes se trouvent souvent en haute densité
cellulaires dans un biofilm. La production d'un glycocalyx, qui est composé principalement
d'EPS, est essentielle pour la formation d'un biofilm. C'est l'EPS qui rend la bactérie
capable de s'attacher aux surfaces et qui protège contre les surfactants et même les anti-
biotiques (O'Toole et al. 2000a). De plus, si un biofilm est composé de plusieurs souches,
comme c'est le cas par exemple dans les intestins, les produits métaboliques d'une souche
peuvent servir comme substrat pour une autre et la capacité de s'attacher d'une cellule peut
procurer des sites d'attachement à d'autres (Dunne 2002). La capacité de s'attacher n'est
toutefois pas toujours avantageuse pour l'homme et peut occasionner des pertes
économiques considérables causées par l'obstruction des conduits d'écoulement des fluides,
5
des filtres ou des échangeurs de chaleur (Bryers 1993). Parfois, la destruction corrosive
causée par des biofilms bactériens peut être une source inépuisable de profit économique,
comme on peut le constater après une visite chez le dentiste.
1.1.2 Utilisations et applications industrielles
Les polysaccharides d'origine microbienne sont toujours en compétition dans les
applications avec d'autres polymères d'origine naturelle ou synthétique. Souvent les
propriétés physiques et écologiques des EPS sont supérieures mais les polysaccharides
d'autres origines sont presque toujours meilleur marché à produire. C'est pourquoi les EPS
doivent avoir un avantage majeur, comme par exemple un bénéfice pour la santé du
consommateur, afin d'arriver à percer sur le marché. En général, les polymères d'origine
microbienne sont des produits uniformes et purs. Dans le cas de la cellulose bactérienne,
produite par exemple par Acetobacter xylinum, ces caractéristiques permettent de produire
des membranes acoustiques de grande fermeté et ainsi de soutenir avec succès la
concurrence de la cellulose végétale. Une autre stratégie est de donner au polymère une
valeur ajoutée par une modification chimique de sa structure. Ainsi, le produit trouve un
champs d'application spécifique comme c'est le cas pour Sephadex®, un dérivé du
dextrane.
Le curdlane est un 1,3-β-glucane d'une taille moléculaire d'environ 74 kDa produit par les
bactéries du genre Agrobacterium et Rhizobium. Il est soluble dans de l'eau froide et forme
un gel faible après chauffage au dessus de 55°C. La fermeté du gel est augmentée avec un
chauffage à plus haute température. Ces gels ont des propriétés se situant entre l'élasticité
de la gélatine et la fragilité de l'agar et ils montrent une bonne capacité de rétention d'eau. À
cause de ces propriétés, le curdlane est utilisé au Japon pour améliorer et modifier la texture
des aliments comme le tofu, les pâtes de poisson et les gels de fèves (Sutherland 1998).
Le pullulane est un α-D-glucane avec des liaisons α-1,6 linéaires, incluant des molécules de
maltotriose et maltotétraose liées α-1,4, et ayant une très bonne solubilité dans l'eau ainsi
qu'en présence d'ions. Ce polysaccharide, synthétisé par Aureobasidium pullulans, est
utilisé au Japon comme film d'emballage alimentaire. Une solution du polymère peut être
6
appliquée directement sur l'aliment et former une couche sans odeur et sans goût
(Sutherland 1998).
Le gellane est un polymère linéaire de 500 kDa, composé d'une unité répétitive de quatre
monomères avec des groupements O-acétyle et glycéryl. Produit par Sphingomonas
paucimobilis, il forme dans sa forme native des gels faibles, élastiques et thermoréversibles.
Il peut former des gels avec une vaste gamme de propriétés par un contrôle du degré de
l'acylation. Ce polymère est permis comme additif alimentaire aux États Unis et en Europe
et commercialisé sous le nom de Kelogen® et Gelrite®. Le gel est caractérisé par une
bonne saveur et est stable sur une vaste gamme de valeurs de pH. Ce polymère est aussi
utilisé pour remplacer l'agar dans les milieux de culture microbiologiques et il est utilisé
comme agent gélifiant dans des produits cosmétiques (Sutherland 1998).
Le xanthane est sans doute le vaisseau amiral parmi les EPS commercialisés et il est permis
comme additif alimentaire aux États Unis et en Europe depuis longtemps. Il est synthétisé
par Xanthomonas campestris et se compose d'une unité répétitive pentasaccharidique, une
épine dorsale cellulosique avec une ramification trisaccharidique contenant le mannose,
l'acide gluconique, l'acétate et le pyruvate. Le degré de ramification et d'acylation peut
différer selon la souche productrice et donner au produit des caractéristiques différentes. En
général, le xanthane se dissout très bien dans l'eau et ses solutions sont pseudoplastiques. Il
peut être utilisé dans une vaste gamme d'aliments, car il est compatible avec la plupart des
autres ingrédients alimentaires, tel que les protéines, les lipides et les autres
polysaccharides. De plus, il est stable dans des conditions acides, ce qui est important dans
plusieurs produits comme les vinaigrettes ou le yoghourt. Le xanthane est souvent utilisé en
combinaison avec d'autres polysaccharides, comme la gomme de caroube, à cause de l'effet
synergique entre ces polymères. Un mélange de deux polymères forme un gel très stable,
bien que chaque polymère seul ne gélifierait pas.
Le dextrane est synthétisé par Ln. mesenteroides dans une solution de saccharose, mais il
peut aussi être produit à partir d'un extrait enzymatique extracellulaire, la dextrane-sucrase.
Il est utilisé, par exemple, dans la récupération assistée de pétrole, comme couche
protectrice pour les graines de céréales, comme agent défloculant pour l’industrie du papier
et, dans le domaine alimentaire, pour la stabilisation et l’épaississement des sirops (Cerning
7
1994). De plus, le dextrane est utilisé comme additif dans le plasma sanguin et pour
moduler l’écoulement du sang.
Il est à noter que la présence d'EPS n'est pas souhaitée dans certains procédés de fabrication
et dans certains produits. Le dextrane, par exemple, a été découvert par accident. Des
mélasses transportées par bateau ont pris une consistance gélifiée et n'ont pas pu être
pompées. La source de ce problème a été une croissance de Ln. mesenteroides dans les
cales du bateau et la transformation du saccharose en dextrane. De plus, la production
d'EPS par certaines souches de Pediococcus dans les vins et les bières et par des souches du
genre Lactobacillus ou Leuconostoc sur des produits carnés emballés sous vide est non-
souhaitée car elle représente une altération du produit rendant celui-ci impropre à la
consommation.
1.2 Exopolysaccharides des bactéries lactiques
En raison de leur forte production, une grande partie des recherches sur les EPS s'est
concentrée sur les bactéries à Gram-negative (Ricciardi et Clementi 2000). Ces bactéries ne
sont pas reconnues comme étant de grade alimentaire et le processus d'approbation de leur
EPS est long. Par contre, les bactéries lactiques (LAB) sont reconnues comme GRAS
(Generally Recognized As Safe) ce qui rend leurs EPS très intéressants pour l'industrie
agroalimentaire (De Vuyst et al. 2001).
Les bactéries lactiques, en raison de leurs caractères technologiques, nutritionnels et
éventuellement thérapeutiques, jouent un rôle central dans le traitement du lait pour obtenir
des produits fermentés comme les fromages et les yoghourts. Par la fermentation, les
bactéries lactiques confèrent les propriétés organoleptiques et rhéologiques particulières
aux produits laitiers fermentés. Pour être classifiée comme bactérie lactique, une souche
doit être Gram-positive, catalase et oxydase négative.
La fermentation est connue depuis des siècles comme procédé de préservation et de
conservation des aliments. Encore aujourd'hui, une vaste gamme d'aliments et de boissons
fermentés est produit à l'aide de différents ferments et technologies. Les propriétés
importantes d'un ferment sont l'acidification rapide, la préservation microbienne du lait, la
8
formation de saveurs spécifiques, les capacités texturantes et les bienfaits pour la santé. La
production d'acides organiques durant la croissance bactérienne cause une acidification du
produit et protège ainsi contre la prolifération des pathogènes.
1.2.1 Composition et structure
Un grand nombre d’EPS microbiens, dont certains possèdent une importance industrielle,
sont des homopolysaccharides. Quoique la chaîne du polymère se compose d’un seul type
de monomère, les propriétés des homopolysaccharides peuvent varier énormément à cause
de leurs structures différentes. Le curdlane, la cellulose et le dextrane, par exemple,
montrent des comportements très différents concernant leur capacités épaississantes, bien
que seul le D-glucose compose leur chaîne. Les homopolysaccharides peuvent être classés
en quatre groupes: α-D-glucanes, β-D-glucanes, fructanes et autres comme polygalactanes.
Les homopolysaccharides ont des poids moléculaires très élevés. Ainsi, la masse
moleculaire du dextrane produit par Ln. mesenteroides NRRL B-512F varie entre 6.2 et
7.1 · 106 Da, et celles des levanes et fructanes, produits par S. mutans vont jusqu'à
21.6 · 106 Da et 12.4 · 106 Da, respectivement (Cerning 1990). La Fig. 1.1 montre comme
exemple la structure du dextrane qui est un homopolymère.
Fig. 1.1 Structure du dextrane, un homopolymère.
Les hétéropolysaccharides microbiens sont composés principalement d’unités répétitives,
variables dans leur taille, soit des di- à octasaccharides. En général, ils ont des poids
9
moléculaires élevés de 5 · 105 à 2 · 106 Da et sont formés d'unités répétitives de 1 à 8
monosaccharides. Parmi ces sucres monomères on trouve le glucose, le galactose, le
rhamnose, le mannose, le N-acétylglucosamine et l'acide glucuronique. De plus, il y a aussi
des résidus qui ne sont pas des sucres, comme le phosphate, l'acétyle et le glycérol. Les
différentes structures des hétéropolysaccharides ont été résumées par De Vuyst et Degeest
(1999b), Riccardi et Clementi (2000), De Vuyst et al. (2001) et Ruas-Madiedo et al.
(2002a). La Fig. 1.2 présente la structure de l'unité répétitive de l'EPS synthétisé par
Lb. rhamnosus RW-9595M. Il s'agit d'un heptasaccharide contenant du glucose, galactose
et rhamnose dans le rapport 2:1:4 et un groupement pyruvate.
α-D-Galp
[3)-α-L-Rhap-(1→3)-β-D-Glcp-(1→3)-α-L-Rhap-(1→3)-α-L-Rhap-(1→3)-α-L-Rhap-(1→2)-α-D-Glcp-(1→]n
1↓2
6H3C
4HO2CR
Fig. 1.2 Structure de l'EPS de Lb. rhamnosus RW-9595M (Van Calsteren et al. 2002).
1.2.2 Fonctionnalité des hétéropolysaccharides
1.2.2.1 Fonctionnalité technologique
La fermeté, la consistance et la capacité de rétention d'eau sont des caractéristiques
importantes dans beaucoup de produits laitiers comme le yoghourt, le fromage et les laits
fermentés. Elles sont fortement influencées par le ferment utilisé. Ainsi, durant la
production d'un yoghourt avec des souches filantes, la fermeté du produit est réduite par la
production d'EPS (Laws et Marshall 2001; Marshall et Rawson 1999). La microscopie
confocale montre des espaces vides autour des bactéries productrices d'EPS dans un
yoghourt, ce qui affecte l'intégrité de la matrice protéique (Hassan et al. 1995). Ainsi, on
constate que des yoghourts faits avec des cultures productrices d'EPS montrent une
rétention d'eau accrue et une susceptibilité diminuée envers la synérèse (Wacher-Rodarte et
al. 1993).
Même si la contribution des EPS à la viscosité des laits fermentés est une supposition
généralement acceptée, il y a très peu d'études caractérisant les EPS sur les aspects
10
rhéologiques. D'ailleurs, il n'y a pas de corrélation claire entre la viscosité des laits
fermentés et la concentration en EPS (Wacher-Rodarte et al. 1993). Sebastiani et Zelger
(1998) n'ont pas pu trouver un rapport entre la quantité d'EPS produite par différentes
souches thermophiles et la viscosité du lait et du milieu M17 fermentés. D'autre part, un
ajout de peptone au milieu a augmenté considérablement la production d'EPS par une
souche de S. thermophilus, de même que la viscosité du milieu. Bouzar et al. (1997) et
Dupont et al. (2000) ont également observé une augmentation de la viscosité du lait
fermenté au cours de la culture avec des souches productrices d'EPS et ont suggéré que la
production d'EPS en est responsable.
Les propriétés rhéologiques des EPS dépendent de plusieurs facteurs. Tout d'abord, la
viscosité intrinsèque est une fonction de la masse moléculaire et du rayon hydrodynamique
du polymère (Tuinier et al. 1999a). Ce rayon est une mesure de la grandeur du polymère et
dépend de sa masse moléculaire et de la flexibilité de la chaîne polymèrique (Tuinier et al.
1999b). Afin d'obtenir une viscosité élevée, la masse moléculaire doit être haute et la
chaîne doit être rigide. La masse moléculaire d'un EPS produit par Lb. sake 0-1 est
comparable au xanthane, avec respectivement 6 · 106 Da et entre 4 · 106 et 9 · 106 Da, mais
sa viscosité est plus élevée (van den Berg et al. 1995). Dans ce cas, c'est la présence du
groupe phosphate avec sa charge négative qui augmente le volume hydrodynamique et la
viscosité intrinsèque (Ruas-Madiedo et al. 2002a). De plus, les différentes ramifications de
la structure des EPS et les interactions des EPS avec d'autres constituants du lait comme les
caséines contribuent aux différents comportements rhéologiques observés.
Récemment, les caractéristiques moléculaires des EPS de plusieurs souches de Lactococcus
lactis ssp. cremoris ont été corrélées avec la viscosité des laits fermentés (Ruas-Madiedo et
al. 2002b). Les auteurs ont montré qu'un EPS produit in situ dans des quantités typiques
d'environ 100 mg/l n'augmente pas significativement la viscosité du lait si sa viscosité
intrinsèque est plus petite que 1.5 m3 kg-1.
1.2.2.2 Fonctionnalité physiologique
Les effets bénéfiques des bactéries lactiques pour la santé du consommateur sont reconnus
depuis longtemps. Déjà, le zoologiste et microbiologiste Ukrainien Ilia Ilitch Metchnikov
11
(1845-1916) a mis en rapport la longévité de certains peuples, dont les Bulgares, et la
protection de l'organisme contre plusieurs maladies par la consommation de laits fermentés
et ainsi l'indigestion de grands quantités de bactéries lactiques. Aujourd'hui, l'incorporation
des bactéries dites probiotiques dans l'alimentation humaine a conduit à l'apparition de
nouveaux produits laitiers dont certains ont un succès considérable sur le marché. Un
probiotique est un supplément alimentaire microbien vivant qui a des effets bénéfiques sur
son hôte en améliorant l'équilibre de la flore intestinale, tandis qu'un prébiotique est un
ingrédient alimentaire non digestible qui a des effets bénéfiques sur son hôte en stimulant
de façon sélective la croissance et/ou l'activité d'une ou plusieurs bactéries présentes dans le
côlon (Gibson et Roberfroid 1995). Les synbiotiques correspondent aux produits dans
lesquels un probiotique et un prébiotique sont présents (Gibson et Roberfroid 1995).
Il a été proposé que l'effet sur la santé des LAB produisant des EPS est attribuable aux
activités biologiques de ce biopolymère. Les EPS pourraient contribuer à la santé humaine
comme prébiotique ou grâce à leurs propriétés anti-tumorales, antivirales, anti-cancérigènes
et immunomodulatrices (De Vuyst et Degeest 1999b). De plus, une diminution du taux de
cholestérol chez des rats ayant consommé du lait fermenté par la souche L. lactis spp.
cremoris SBT 0495 a été observée et attribuée à l'EPS produit par cette souche (Nakajima
et al. 1992).
L'EPS de Lb. rhamnosus RW-9595M a été testé in vitro pour ses propriétés
immunomodulatrices sur des cellules de souris et humaines (Chabot et al. 2001). Les
auteurs montrent une stimulation de la production de TNF, IL-6 et IL-12 des cellules
humaines et des souris et de IFN-γ de splénocytes des souris. Ces résultats suggèrent la
possibilité de stimuler le système immunitaire par l'EPS des LAB, dans les individus
sensibles à un tel stimulus (Chabot et al. 2001).
La susceptibilité à la digestion pourrait être une caractéristique importante pour le rôle
possible d'un EPS comme prébiotique, car, comme déjà mentionné, une des caractéristiques
d'un prébiotique est sa non-digestibilité par l'humain. En soumettant la souche L. lactis ssp.
cremoris MG1614 et son variant isogénique NZ4010 et producteur d'EPS à des conditions
de digestion in vitro, Looijesteijn et al. (2001) ont trouvé que la présence de l'EPS ne
protège pas la souche productrice lors du transit digestif, même si l'EPS n'était pas dégradé.
12
Lors d'une étude de biodégradabilité des EPS par des microorganismes gastrointestinaux
humains (Ruijssenaars et al. 2000), les EPS produit par S. thermophilus SFi39 et SFi12 ont
été dégradés contrairement à ceux produits par Lb. sake 0-1, S. thermophilus SFi20 et
Lb. helveticus Lh59. Afin de prouver le potentiel prébiotique des EPS des LAB, des études
supplémentaires sur leur biodégradabilité et leur décomposition par la communauté
bactérienne gastro-intestinale doivent être réalisées.
Plusieurs études ont proposé que les EPS ont une activité anti-cancérigène. Kitazawa et al.
(1991) ont postulé que l'EPS produit par L. lactis ssp. cremoris KVS 20 est responsable
d'un effet anti-tumoral de cette souche. Ceci a été observé lors d'injections intrapéritonéales
chez des souris. Dans une étude subséquente, Kitazawa et al. (1996) ont attribué à un
exophosphopolysaccharide produit par cette souche une activation des macrophages et
l'induction de la production de cytokine. Kitazawa et al. (1998) ont fractionné l'EPS produit
par Lb. delbrueckii ssp. bulgaricus OLL 1073R-1 en un polysaccharide neutre et un
polysaccharide acide. La fraction acide composée de glucose, galactose et phosphore a
démontré une activité mitogénique sur les lymphocytes B, dirigée par le groupement
phosphate. Une activité mitogénique a aussi été observée in vitro pour un polysaccharide
d'une taille de 1.5 · 106 Da produit par Bifidobacterium adolescentis M101-4 (Hosono et al.
1997). Un effet anti-cancérigène a été trouvé in vitro et in vivo pour les polysaccharides
capsulaires de Bifidobacterium breve YIT4014 et 4043 et Bifidobacterium bifidum YIT
4007 (Nagaoka et al. 1994). Ces polysaccharides étaient composés principalement de
rhamnose. Il a été montré que les polysaccharides contenant plus de 60% de rhamnose se
sont montrés plus efficaces pour le traitement du cancer gastro-intestinal.
Tous les travaux mentionnés jusqu'ici ont été fait in vitro ou par injection de l'EPS à des
rats ou des souris. Très peu d'expériences ont été réalisées in vivo avec administration orale
de l'EPS. Zubillaga et al. (2001) ont administré l'EPS KGF-C oralement. Les auteurs ont
observé un retardement de la croissance des cellules cancéreuses par cet EPS soluble dans
l'eau et extrait de grains de kéfir.
13
1.2.3 Biosynthèse des hétéropolysaccharides des bactéries lactiques
Le site de la synthèse des EPS et la nature des précurseurs permettent de distinguer deux
types principaux de biosynthèse par les LAB: la synthèse en dehors de la cellule
(produisant des homopolysaccharides) ou celle à la membrane cellulaire (produisant des
hétéropolysaccharides). Dans le premier cas, ce sont principalement, Ln. mesenteroides
(dextranes), S. mutans (mutanes) et S. salivarius (levanes) qui produisent des
homopolysaccharides; alors que les hétéropolysaccharides sont produits par des bactéries
lactiques mésophiles (ex. L. lactis, L. cremoris, Lb. casei) et thermophiles (ex. Lb.
bulgaricus, S. thermophilus).
Les homopolysaccharides sont synthétisés en dehors de la cellule grâce à des enzymes
excrétés par la bactérie. Dans la production du dextrane, par exemple, seulement une
enzyme est utilisée, la dextranesucrase. Cet enzyme est spécifique pour le sucrose et
l'énergie pour la polymérisation vient de son hydrolyse. Le dextrane peut être produit à
partir de cultures cellulaires de Ln. mesenteroides ou de préparations de l'enzyme sans
cellules vivantes, éventuellement immobilisée (Cerning 1990).
La synthèse des hétéropolysaccharides, par contre, a lieu à la membrane cytoplasmique.
L'EPS est construit par polymérisation des unités répétitives formées dans le cytoplasme
(Cerning 1990; De Vuyst et Degeest 1999b). L'unité répétitive est assemblée à la
membrane cytoplasmique par addition successive d'unités glucosyle au polysaccharide
naissant qui est probablement ancré sur un transporteur lipidique, nommé C55. Après
complétion de l'unité répétitive, celle-ci est transportée au travers de la membrane cellulaire
et polymérisée à l'extérieur de la cellule pour former l'hétéropolysaccharide, avec un poids
moléculaire finale élevé d'environ 1 · 106 Da. La synthèse des hétéropolysaccharides par
des LAB implique donc un grand nombre d’enzymes différentes comme, par exemple,
l’UDP-glucose déshydrogénase, la glucosyl-transférase et la galactosyl-transférase.
Plusieurs de ces enzymes ne sont pas seulement actives dans la synthèse des EPS, mais
aussi impliquées dans d’autres activités métaboliques. La Fig. 1.3 montre les voies
métaboliques impliquées dans le catabolisme des sucres et dans l'anabolisme des EPS chez
certaines bactéries lactiques. On voit l'importance des sucres nucléotidiques, dérivés des
14
sucres-1-phosphates qui, après avoir été transformés par des enzymes d'épimérisation, de
décarboxylation, de phosphorylation et de déshydrogénation, sont assemblés pour former
l'unité répétitive de l'EPS. Les précurseurs intracellulaires ont été dosés par résonance
magnétique nucléaire 31P pour deux souches de Lactococcus lactis, une souche productrice
(EPS+) et une non-productrice (EPS-) (Ramos et al. 2001). Les concentrations des
précurseurs d'EPS, l'UDP-glucose et l'UDP-galactose, ont été plus faibles dans la souche
EPS+ que dans la souche EPS-. Les précurseurs de la biosynthèse du peptidoglycane,
l'UDP-N-acétylglucosamine et l'UDP-N-acétylmuramoyl-pentapeptide, ont été les produits
derivés des UDP-sucres majeurs détectés chez les deux souches, mais leur concentration a
été plus élevée dans la souche EPS+, ce qui confirme la compétition entre la synthèse d'EPS
et la croissance cellulaire (Ramos et al. 2001).
Une fois que les sucres nucléotidiques sont formés, les glycosyl-tranférases commencent
leur activité pour la formation de la chaîne de sucres (Fig. 1.4). Ces enzymes spécifiques
attachent le premier monomère au transporteur lipidique qui se trouve ancré à la paroi
cytoplasmique. Dans la synthèse des hétéropolysaccharides, les transporteurs lipidiques
semblent jouer un rôle important. Ce sont des esters phosphates et des alcools isoprénoïdes
à longues chaînes, identiques à ceux décrits dans la biosynthèse des lipopolysaccharides, de
l’antigène O et du peptidoglycane (Sutherland 1990). Le rôle des transporteurs lipidiques
dans la synthèse des EPS serait de servir d'ancrage et de faciliter la formation précise et
ordonnée de la chaîne glucidique et le transport à travers la membrane cellulaire. Les sous-
unités répétitives sont assemblées sur le côté interne de la membrane et ensuite chaque
sous-unité est transféré au travers la membrane. Une fois à l'extérieur de la cellule,
plusieurs centaines, voir milliers, d'unités répétitives sont liés ensemble par une
polymérase. Certains polysaccharides sont polymérisés sur le côté interne de la membrane
cytoplasmique suivi de l'exportation du polymère. Certaines protéines, liés à des lipides,
pourraient jouer un rôle comme flippase-exportateur et polymérase de l'unité répétitive (De
Vuyst et al. 2001). Après l'excrétion, le polymère est soit libéré ou reste attaché à la surface
de la cellule formant la capsule. Le mécanisme de la polymérisation, de la détermination de
la longueur de chaîne, et de l'exportation n'est pas encore clair.
15
Fig. 1.3 Schéma des voies métaboliques impliquées dans le catabolisme du
lactose/galactose et la biosynthèse des EPS par Lactococcus lactis Gal+ (via les systèmes
phosphoénolpyruvate PEP et phospho-transférase PTS) et par Lactobacillus delbrueckii
ssp. bulgaricus et Streptococcus thermophilus Gal- (via l'antiport lactose/galactose) (De
Vuyst et al. 2001).
Les numéros se rapportent aux enzymes impliquées: (1) phospho-β-galactosidase, (2) β-galactosidase, (3) glucokinase, (4) phosphoglucomutase, (5) UDP-glucose pyrophosphorylase, (6) UDP-galactose 4 epimérase, (7) dTDP-glucose pyrophosphorylase, (8) deshydratase, (9) epimérase réductase, (10) phosphoglucose isomérase, (11) 6-phosphofructokinase, (12) fructose-1,6-bisphosphatase, (13) fructose-1,6-di-phosphate aldolase, (14) galactose 6-phosphate isomérase, (15) tagatose 6-phosphate kinase, (16) tagatose-1,6-di-phosphate aldolase, (17) galactokinase, (18) galactose-1-phosphate uridylyltransférase, (19) glutamine-fructose-6-phosphate transaminase, (20) glucosamine-phosphate acétyltransférase, (21) acétylglucosaminephosphate mutase, (22) UDP-glucosamine pyrophosphorylase, (23) UDP-N-acétylglucosamine 4-epimérase.
16
Les alcools isoprénoïdes ne sont pas seulement impliqués dans la production des
lipopolysaccharides, mais aussi dans celle des peptidoglycanes et acides téichoïques.
Comme la disponibilité de l’alcool isoprénoïde est essentielle pour la production des EPS,
la compétition pour cette substance a un effet direct sur la production. Si les bactéries ont
une croissance lente, leur besoin en phosphate d’isoprénoïde pour la formation des
polymères de la paroi est réduit et la production d’EPS dispose d'une plus grande quantité
de ces molécules. Pour cette raison, une meilleure production d’EPS dans des conditions
moins propices à la croissance des bactéries a été souvent observée, surtout pour les LAB
mésophiles (Cerning 1990; De Vuyst et Degeest 1999b) (voir aussi chapitre 1.2.5.5).
Fig. 1.4 Modèle de la biosynthèse d'EPS par Lactococcus lactis ssp. lactis NIZO B40 (Van
Kranenburg et al. 1998)
Après la formation des unités répétitives, celles-ci sont transportées au travers de la
membrane, probablement à l'aide d'une flippase, puis polymérisées et excrétées dans le
milieu environnant (Van Kranenburg et al. 1997).
17
Depuis une décennie, il y a eu plusieurs études sur les mécanismes de la biosynthèse des
EPS et les voies métaboliques sont maintenant relativement bien connues. Ceci permet de
mieux comprendre l'influence des conditions de culture et du milieu de culture sur la nature
et la composition des EPS (voir chapitre 1.2.5). De plus, une connaissance approfondie des
voies métaboliques permet d'identifier les enzymes clés de la production d'EPS et ainsi, par
le génie génétique, de moduler cette production et de créer des souches hyperproductrices
d'EPS ayant une structure définie (Ramos et al. 2001).
1.2.4 Génétique de la production des hétéropolysaccharides
Le premier travail portant sur les gènes structuraux impliqués dans la production des EPS
par les LAB a porté sur les gènes chez S. thermophilus Sfi6 (Stingele et al. 1996). Les
auteurs ont trouvé un seul locus chromosomique responsable pour la production d'EPS. Par
la suite, Van Kranenburg et al. (1997) ont identifié les gènes responsables de la production
d'EPS chez L. lactis NIZO B40 (Van Kranenburg et al. 1997) et ont montré que ces gènes
sont de nature plasmidique. Depuis, plusieurs recherches sur la génétique de la biosynthèse
d'EPS par les LAB ont été réalisées et les gènes impliqués ont été identifiés (pour une revue
récente voir Jolly et Stingele 2001). Dans tous les cas, ces gènes sont organisés dans un
locus montrant une bonne conservation en ce qui concerne leur organisation (Boels et al.
2001). La séquence des fonctions de tout ces opérons semble être comme suit: régulation,
détermination de la longueur de la chaîne, biosynthèse de l'unité répétitive, polymérisation
et exportation (Jolly et Stingele 2001).
Les deux opérons eps des LAB les mieux caractérisés sont probablement ceux de L. lactis
NIZO B40 et de S. thermophilus Sfi6. L. lactis NIZO B40 héberge le plasmide pNZ4000 de
42,180 pb qui contient l'opéron eps de 12 kb (voir Fig. 1.5) (van Kranenburg et al. 2000).
Par la comparaison des séquences, les fonctions de la plupart des gènes ont pu être
trouvées. Les produits des gènes epsDEFGH et epsJ sont supposés agir comme
glycosyltransférases avec comme premier enzyme le EpsD qui commence avec la
construction de la chaîne glucidique de l'unité répétitive en attachant une molécule glucose
de l'UDP-glucose à un transporteur lipidique (Van Kranenburg et al. 1997). Ensuite, les
autres glycosyltransférases EpsE, EpsF, EpsG continuent à construire l'épine dorsale de
18
l'unité répétitive. EpsH et EpsJ sont supposés être impliqués dans l'attachement des
molécules de ramification, le rhamnose et le galactose-phosphate. EpsI et EpsK sont
homologues à des protéines de polymérisation et d'exportation impliquées dans la
production des lipopolysaccharides chez les bactéries Gram-négatives.
Chez S. thermophilus Sfi6, un locus chromosomique d'une taille de 14.52 kb regroupe les
13 gènes epsA à epsM dont les produits sont impliqués dans la production de l'EPS
(Stingele et al. 1996). La Fig. 1.5 montre l'organisation de ce locus. L'expression des gènes
epsE, epsF, epsG et epsI dans Escherichia coli et des réactions des glycosyl transférases in
vitro a permis d'identifier les produits EpsE comme étant une β-galactose transférase, EpsG
une α-1,3-N-acétylgalactosamine transférase et EpsI une β-1,3-glucose transférase. EpsF
serait alors un α-1,6-galactose transférase, car epsF est le seul gène codant pour une
glycosyltransférase qui n'a pas été assigné. Les gènes epsC et epsD sont putativement
impliqués dans la polymérisation des unités tandis que epsM serait responsable de
l'exportation. Finalement, epsJ serait impliqué dans la polymérisation des unités répétitives.
Ces dernières années, plusieurs travaux sur la biosynthèse des EPS par les LAB ont été
conduits. Pour certaines souches, les séquences de gènes codant pour la production d'EPS,
la structure de l'EPS correspondant et les voies métaboliques des sucres sont connues.
Cependant, il y a encore une manque de donnés sur le rapport entre les séquences de gènes
et la production d'EPS. Il reste à éclaircir s'il y a des éléments contrôlant l'expression des
gènes, où si les gènes sont toujours actifs, et le niveau de contrôle se trouve plutôt avec
l'activité des enzymes impliquées. Néanmoins, il a déjà été possible de contrôler la
production d'EPS non seulement par les conditions de fermentation mais aussi en
appliquant des techniques génétiques. Les premiers résultats utilisant l'expression
hétérologue des gènes eps de S. thermophilus Sfi6 dans la souche L. lactis MG1363 EPS-
montrent que cette technique peut résulter dans la production d'EPS par la souche réceptrice
(Stingele et al. 1996). Toutefois, seulement de faibles quantités d'EPS ont été produites
dans l'hôte hétérologue. L'EPS produit avait une masse moléculaire semblable mais une
structure différente de celle de la souche originale. Même si une meilleure connaissance des
mécanismes impliqués est encore nécessaire, ces résultats sont très prometteurs pour des
travaux futurs. La sur-expression des gènes eps peut résulter dans des productivités
19
augmentées et les EPS produits peuvent avoir des structures et des propriétés modifiées et
ils pourraient être utilisés comme nouveaux agents épaississants. Cependant, les LAB
génétiquement modifiées et leur produits doivent être approuvés légalement et être acceptés
par les producteurs et consommateurs.
Fig. 1.5 Organisation des gènes codant pour la production d'EPS chez Lactococcus lactis
NIZO B40 (plasmidique) et chez Streptococcus thermophilus Sfi6 (adapté de De Vuyst et
al., 2001).
1.2.5 Production des hétéropolysaccharides par les bactéries lactiques
Les propriétés des EPS des LAB peuvent différer considérablement d'une souche à l'autre.
Leur biosynthèse et sécrétion peut avoir lieu durant des phases de croissance différentes. En
outre, les conditions de croissance comme la composition du milieu de culture, la
température, le pH, la tension d'oxygène et la vitesse d'agitation peuvent influencer la
quantité mais aussi la composition et la taille de l'EPS. Cependant, des résultats
contradictoires ont été rapportés concernant l'influence de ces paramètres sur la production
des EPS.
20
1.2.5.1 Milieux utilisés pour la production d'EPS
Au début des recherches sur la production des EPS par les LAB, aucune production n'a été
observée dans des milieux semi-définis comme le MRS. Ainsi, plusieurs travaux ont été
réalisés dans le lait (Cerning et al. 1986; 1988; Cerning et al. 1990; 1992; De Vuyst et al.
1998; Garcia-Garibay et Marshall 1991) ou dans un milieu à base du lactosérum (Gassem et
al. 1997a; Macedo et al. 2002a; Macedo et al. 2002b). Seulement récemment des milieux
semi-synthétiques et synthétiques ont été utilisés (Cerning et al. 1994; Dupont et al. 2000;
Grobben et al. 2000; Grobben et al. 1995; Grobben et al. 1996; Grobben et al. 1997;
Kimmel et Roberts 1998; Petry et al. 2000; Pham et al. 2000; Torino et al. 2000; van den
Berg et al. 1995). En effet, un milieu chimiquement défini est plus approprié pour l'étude
de la biosynthèse des EPS par les LAB et des voies métaboliques impliquées. Dans ces
milieux il n'y a pas de composants qui interférent avec la quantification et avec l'analyse
des EPS. Pourtant, les composants des milieux complexes, comme le peptone ou l'extrait de
bœuf ou de levure, permettent une bonne croissance des LAB et souvent même une bonne
production d'EPS, mais ils contiennent d'autres polymères pouvant interférer avec le dosage
et l'analyse des EPS (Kimmel et Roberts 1998; Torino et al. 2000).
1.2.5.2 Rendement de la production d'EPS
La production d'EPS par les souches productrices varie énormément et dépend des
conditions de culture des bactéries. Une comparaison des données de la littérature des
rendements en EPS par les LAB doit être faite avec réserve car des techniques de
quantification et des milieux de culture différents ont été utilisés. Ceci peut avoir une forte
influence sur les résultats (voir aussi chapitre 1.2.6.1). Une vue d'ensemble sur les
productions d'EPS les plus importantes est donnée dans le Tab. 1.1. En général, des
concentrations d'EPS de 50 à 600 mg/l dans des conditions optimales de production ont été
obtenues (De Vuyst et Degeest 1999b; Ricciardi et Clementi 2000). Par contre, des
productions maximales de 1.14 g/l par S. thermophilus LY03 (Degeest et de Vuyst 1999),
de 1.37 g/l par Lb. sakei 0-1 (van den Berg et al. 1995) et de 2.77 g/l par Lb. rhamnosus
RW-9595M (Macedo et al. 2002b) ont été rapportées. Un effet synergique entre les souches
thermophiles S. thermophilus et Lb. delbrueckii ssp. bulgaricus a été observé dans deux
21
études différentes (Tab. 1.1). Une souche productrice d'EPS de S. thermophilus (CNRZ
1066) en combinaison avec une souche non-productrice de Lb. delbrueckii ssp. bulgaricus
(CNRZ 398) a produit une quantité d'EPS (800 mg/l) beaucoup plus élevée que la souche
productrice seule (Cerning et al. 1990). De plus, la production de la souche Lb. delbrueckii
ssp. bulgaricus CNRZ 1187 a été plus élevée en culture mixte avec une souche non-
productrice de S. thermophilus qu'en culture pure (Bouzar et al. 1996; 1997).
22
Tab.
1.1
Pro
duct
ion
d'EP
S pa
r les
LA
B.
Souc
he
Mili
eu d
e cu
lture
T
ype
de
cultu
re
CE
PS
(mg/
l) R
éfér
ence
Lb. d
elbr
ueck
ii ss
p. b
ulga
ricu
s CN
RZ
737
737
S. th
erm
ophi
lus C
NR
Z 10
66
337
S. th
erm
ophi
lus C
NR
Z 10
66 +
Lb
. del
brue
ckii
ssp.
bul
gari
cus C
NR
Z 39
8
Lait
écré
mé
B
800
(Cer
ning
et a
l. 19
90)
S. th
erm
ophi
lus
M17
+ la
c B
, FB
; pH
25
00-3
000
Petit
et a
l., 1
991
S. th
erm
ophi
lus L
Y03
M
RS
B; p
H
1142
Deg
eest
et D
e V
uyst
, 199
9 S.
ther
mop
hilu
s SD
M
B; p
H
546
De
Vuy
st e
t al.,
199
8 Lb
. del
brue
ckii
ssp.
bul
gari
cus C
NR
Z 11
87
Lait
écém
é B
13
0(B
ouza
r et a
l. 19
96)
Lb. d
elbr
ueck
ii ss
p. b
ulga
ricu
s CN
RZ
1187
+ S
. the
rmop
hilu
s EPS
- La
it éc
rém
é B
24
0(B
ouza
r et a
l. 19
97)
CD
M +
glu
B
; pH
80
Gro
bben
et a
l., 1
995
CD
M
+ gl
u +
fruc
C
; pH
25
-125
Gro
bben
et a
l., 1
996
Lb. d
elbr
ueck
ii ss
p. b
ulga
ricu
s NC
FB 2
772
mC
DM
+ g
lu
B; p
H
250
Gro
bben
et a
l., 1
997
Lb. d
elbr
ueck
ii ss
p. b
ulga
ricu
s RR
PL
S C
; pH
21
30G
asse
m e
t al.,
199
7 Lb
. sak
e 0-
1 SD
M
B; p
H
1375
Van
den
Ber
g et
al.,
199
5
Lb. c
asei
CR
L87
CD
M
+ m
inér
aux
B; p
H
488
Moz
zi e
t al.,
199
6
Lb. r
ham
nosu
s 85
Lb. r
ham
nosu
s R
601
Lb. r
ham
nosu
s RW
-959
5M
BM
M +
lac
B; p
H
1275
Dup
ont e
t al.,
2000
Lb. r
ham
nosu
s RW
-959
5M
PLS
+ EL
+
BM
M c
omp
B; p
H
2775
(Mac
edo
et a
l. 20
02b)
L. la
ctis
ssp.
cre
mor
is S
BT0
495
LS
B; p
H
500
Nak
ajim
a et
al.,
199
0 C
DM
: mili
eu c
him
ique
men
t déf
ini.
SDM
: mili
eu se
mi-d
éfin
i. m
CD
M: m
ilieu
chi
miq
uem
ent d
éfin
i mod
ifié.
PLS
: per
méa
t de
lact
osér
um.
LS: l
acto
séru
m. E
L: e
xtra
it de
levu
re. B
MM
com
p: v
itam
ines
, sel
s et a
cide
s am
inés
du
mili
eu se
mi-d
éfin
i BM
M.
B: f
erm
enta
tion
en b
atch
. FB
: fer
men
tatio
n en
fed-
batc
h. C
: fer
men
tatio
n en
con
tinu.
pH
: ave
c co
ntrô
le d
e pH
23
1.2.5.3 Effet du milieu de culture sur la production
1.2.5.3.1 Source d'azote
Plusieurs des premières recherches sur la production d'EPS par les LAB ont été conduites
avec un milieu à base du lait. Il a été observé que l'addition des caséines hydrolysées au lait
a augmenté la croissance et la production d'EPS d'une culture de Lb. delbrueckii ssp.
bulgaricus (Cerning et al. 1990; Garcia-Garibay et Marshall 1991). Toutefois, dans une
étude de Cerning et al. (1986), la caséine a stimulé la production d'EPS par Lb. delbrueckii
ssp. bulgaricus mais pas sa croissance. Néanmoins, une souche de S. thermophilus peut
produire la même quantité d'EPS dans le lait ou le lait ultrafiltré (Cerning 1990). La
stimulation de la production d'EPS par la caséine hydrolysée reste controversée. D'une part
son addition à une culture de Lb. delbrueckii ssp. bulgaricus dans un milieu défini MRS
n'augmente pas la production spécifique (Garcia-Garibay et Marshall 1991), mais c'est le
contraire qui se produit pour un milieu semi-défini à base de lactosérum (Kimmel et al.
1998).
Pour certaines bactéries Gram-négatif comme des souches de Xanthomonas, Pseudomonas
et Rhizobium, une limitation de l'azote résulte en une production accrue d'EPS (Sutherland
1990). Pour les bactéries lactiques, cela ne semble pas être le cas. Il semble plutôt qu'un
équilibre optimal entre la source de carbone et d'azote soit nécessaire pour obtenir des
productions élevées d'EPS (De Vuyst et Degeest 1999b). La souche L. lactis ssp. cremoris
LC 330 produit deux EPS différents (Marshall et al. 1995), un EPS neutre avec une haute
masse moléculaire et un phosphopolysaccharide chargé, d'une masse moléculaire plus
petite. Les auteurs ont montré qu'une limitation par l'azote stimule la production de l'EPS
neutre mais pas celle de l'EPS chargé. Une étude sur l'effet de la concentration de
bactocasitone entre 10 et 40 g/l dans un milieu semi-défini pour des fermentations de Lb.
delbrueckii ssp. bulgaricus RR a montré qu'une concentration de 30 g/l est optimale pour la
production d'EPS (354 mg/l) (Kimmel et al. 1998).
Une étude sur l'effet de différentes sources d'azote sur la croissance de Lb. rhamnosus
RW-9595M dans un milieu à base de perméat de lactosérum a identifié un isolat de
protéine de lactosérum, un concentré de protéine de lactosérum et un extrait de levure
24
comme étant les meilleures sources d'azote (Macedo 2001). Aucune différence significative
entre ces trois milieux a été observée pour la biomasse maximale lors des fermentations,
tandis que la production d'EPS a été maximale avec le concentré de protéine de lactosérum.
Dans un travail ultérieur sur l'effet d'une supplémentation d'un milieu à base de perméat de
lactosérum et de l'extrait de levure avec des groupes de nutriments utilisés dans la
formulation du BMM, une influence significative du groupe des acides aminés sur la
production d'EPS par Lb. rhamnosus RW-9595M a été observée (Macedo et al. 2002b).
1.2.5.3.2 Source de carbone
La source de carbone a une influence majeure sur la biosynthèse des EPS par les LAB. En
plus du type de sucre (glucose, galactose, lactose, mannose, fructose etc.) et du rapport
entre eux, la concentration des sucres peut avoir un effet stimulant sur la production
(Cerning et al. 1992; Cerning et al. 1994; Gamar et al. 1997). La production d'EPS par
Lb. delbrueckii ssp. bulgaricus a été plus grande dans un milieu avec du glucose ou du
lactose que dans un milieu avec du fructose, tandis que la supplémentation en mannose a
résulté en une croissance et une production d'EPS faible (Grobben et al. 1995; Grobben et
al. 1996). Gancel et Novel (1994) ont comparé le rendement en EPS de S. salivarius ssp.
thermophilus. Le rendement avec le milieu contenant du glucose et du fructose a été plus
élevé qu’avec le lactose ou le saccharose, tandis que la prolifération des bactéries a été
moins rapide. Cerning et al. (1994) ont étudié la production d’EPS par Lb. casei CG11 en
variant la source de carbone (galactose, glucose, lactose, saccharose, maltose, mélibiose).
Ils ont trouvé qu’avec le lactose et le galactose, la production d’EPS a été la plus faible,
alors que le glucose a été de loin la source la plus efficace. Pour Lb. rhamnosus C83, le
mannose ou une combinaison de glucose et de fructose ont favorisé la production d'EPS
(Gamar et al. 1997). Une combinaison de glucose et de lactose dans un milieu de culture a
augmenté la production d'EPS par S. thermophilus LY03 et S. thermophilus Sfi20, comparé
avec un milieu de culture avec le glucose ou le lactose seul, même si la concentration totale
des sucres était la même (7.5%) (Degeest et de Vuyst 2000; Degeest et al. 2001b).
25
1.2.5.3.3 Minéraux et vitamines
Les minéraux et les vitamines ont aussi une forte influence sur la croissance des LAB et
leur production d'EPS. Par exemple, la production d'EPS par Lb. casei CRL 7 a doublé
après ajout de Mn2+ dans un milieu défini (1995a; Mozzi et al. 1995b). Grobben et al.
(1998) ont examiné les besoins nutritionnels de Lb. delbrueckii ssp. bulgaricus NCFB 2772
en utilisant un milieu défini. Ils ont trouvé une augmentation de la production spécifique
d'EPS de 130 à 250 mg/l après omission de plusieurs vitamines non-essentielles du milieu
défini. Enfin, Macedo et al. (2002b) n'ont pas trouvé un effet significatif du groupe des
vitamines, utilisées dans la formulation du BMM, sur la production d'EPS par
Lb. rhamnosus RW-9595M dans un milieu à base de perméat de lactosérum et d'extrait de
levure. Toutefois, l'adition du groupe des minéraux a eu une influence majeure et a
augmenté considérablement la production d'EPS. La production maximale en EPS dans
cette étude de 2775 mg/l a été atteint dans un milieu perméat de lactosérum supplémenté
avec d'extrait de levure, des minéraux, des sels et des acides aminés.
1.2.5.4 Effet du milieu sur la composition de l'EPS
D'après Sutherland (1972), la composition du milieu n'a pas d'effet sur la composition de
l'EPS produit. Cependant, un changement majeur de la composition en monosaccharides
des EPS produits par les LAB selon la composition du milieu de culture a depuis souvent
été observé. L'addition de glucose et de saccharose au milieu lait ou lait ultrafiltré n'a pas
seulement stimulé la production d'EPS par Lb. casei mais aussi changé sa composition, le
glucose devenant le monosaccharide dominant (Cerning et al. 1992). Contrairement à l'EPS
produit par cette souche sur le milieu BMM (Cerning et al. 1994), le rhamnose ne se
retrouvait plus dans la composition de l'EPS. Les auteurs ont conclu que cette souche était
capable de produire plus qu’un seul type d’EPS. En outre, ils ont trouvé que la dégradation
des EPS par la glycohydrolase a été arrêtée après avoir supplémenté le milieu de
fermentation avec du glucose. On peut en conclure que, soit l’activité de l’enzyme a été
inhibée en présence de glucose, soit le changement de composition des monomères de
l’EPS a rendu l’enzyme, fortement spécialisé, incapable de dégrader le polymère. Grobben
et al. (1996) ont montré que la quantité et la composition de l'EPS
26
(galactose : glucose : rhamnose; 6.8 : 1.0 : 0.7) produit par Lb. delbrueckii ssp. bulgaricus
NCFB 2772 dans des cultures en continu ne change pas si la culture croît sur du lactose au
lieu de glucose. Cependant, avec du fructose comme source de carbone, la production a été
inférieure et le rhamnose a été absent de la composition de l'EPS (galactose : glucose;
2.5 : 1.0). Les auteurs ont aussi conclu que la souche produit plus qu'un polysaccharide.
Dans une étude ultérieure (Grobben et al. 1997), deux EPS avec des masses moléculaires
différentes ont été caractérisés. La production d'un EPS d'une masse moléculaire élevée,
ayant une composition en galactose, glucose et rhamnose dans un rapport de 5.0 : 1.0 : 1.0,
a été dépendante de la source de carbone, tandis que l'EPS d'une masse moléculaire plus
petite, ayant une composition en galactose, glucose et rhamnose dans un rapport de
11.0 : 1.0 : 0.4, a été produit plus constamment, indépendamment de la source de carbone.
1.2.5.5 Cinétique de la production des EPS par les bactéries lactiques
Il semble que les LAB mésophiles ont une production maximale d'EPS dans des conditions
de croissance sous-optimales (Cerning et al. 1992; Gamar et al. 1997; Gancel et Novel
1994; Gassem et al. 1997a; Kojic et al. 1992; Looijesteijn et al. 1999; Marshall et al. 1995;
Mozzi et al. 1995a; van den Berg et al. 1995), tandis que la production d'EPS des LAB
thermophiles semble être associée à la croissance (De Vuyst et al. 1998; Garcia-Garibay et
Marshall 1991; Grobben et al. 1995; Mozzi et al. 1995a). Si la production d'EPS est
associée à la croissance, la biosynthèse de l'EPS commence directement avec la croissance
bactérienne et montre la cinétique d'un métabolite primaire. Par exemple, une culture de
Lb. rhamnosus C83 dans un milieu défini sans contrôle de pH a montré une production
simultanée d'EPS, de lactate et de la biomasse (Gamar et al. 1997). Les auteurs ont conclu à
une production d'EPS associée à la croissance. Par contre, une culture de Lb. rhamnosus R
dans le milieu BMM et avec contrôle de pH a commencé à produire l'EPS seulement à la
fin de la phase exponentielle de croissance (Pham et al. 2000). De plus, la production d'EPS
a continué pendant la phase stationnaire de croissance dans le cas des cultures dans le
glucose, tandis que la production d'EPS a cessé dans le cas d'une culture dans un milieu
additionné de lactose. Les auteurs ont supposé que l'EPS produit par cette souche peut être
considéré plutôt comme un produit mineur détourné de la glycolyse que comme un
métabolite secondaire. De plus, la souche L. lactis ssp. cremoris NIZO B40 a produit la
27
majorité de l'EPS pendant la phase exponentielle de croissance, lorsque la souche croissait
dans un milieu avec le glucose comme source de carbone, tandis qu'avec le fructose, la
souche produisait environ 60% de l'EPS dans la phase stationnaire de croissance. Dans une
étude sur la production d'EPS par Lb. rhamnosus RW-9595M dans un milieu à base de
perméat de lactosérum additionné de yeast nitrogen base (YNB) comme source d'azote, la
température de la culture a été variée entre 22 et 42°C (Macedo et al. 2002a). Les auteurs
ont montré que la production d'EPS n'était pas liée à la croissance cellulaire pour des
températures élevées, alors que c'était le contraire à des températures sub-optimales.
Pour les LAB mésophiles, des conditions de culture comme la température, le pH ou la
composition du milieu peuvent permettre de découpler la croissance cellulaire de la
production d'EPS (Looijesteijn et Hugenholtz 1999). La production d'EPS peut être
augmentée en appliquant les conditions environnementales stimulant la biosynthèse d'EPS
une fois qu'assez de biomasse est formée (Degeest et al. 2001a). L'immobilisation cellulaire
pourrait être un moyen efficace de découpler la croissance cellulaire de la production d'EPS
et de garder une biomasse élevée dans un système de fermentation, tout en appliquant des
conditions de fermentation propices à la production d'EPS (voir chapitre 1.3).
1.2.5.6 Effets des conditions de culture
Lors des fermentations, les conditions optimales de température, pH, tension d'oxygène,
vitesse d'agitation et temps d'incubation résultent en un rendement en EPS amélioré (De
Vuyst et Degeest 1999b; Degeest et al. 2001a; Ricciardi et Clementi 2000). Cependant,
plusieurs études montrent que des températures sub-optimales influencent positivement la
production d'EPS par les LAB mésophiles et thermophiles (Cerning 1990; Cerning et al.
1992; Gamar et al. 1997; Gancel et Novel 1994; Gassem et al. 1997a; Kojic et al. 1992;
Kontusaari and Forsen 1988; Looijesteijn et Hugenholtz 1999; Marshall et al. 1995; Mozzi
et al. 1996b; van den Berg et al. 1995). Encore une fois, ces observations ont été expliquées
par la disponibilité plus élevée du transporteur lipidique chez des bactéries en croissance
lente (voir chapitre 1.2.3). Par exemple, un changement de la température de 37 à 25°C au
début de la phase exponentielle de croissance a amélioré significativement la production
d'EPS chez Lb. rhamnosus C83 (Gamar-Nourani et al. 1998). Garcia-Garibay et Marshall
28
(1991) ont trouvé une production spécifique d’EPS deux fois plus élevée pour une
température (48°C) supérieure à la température optimale de la croissance de la souche Lb.
delbrueckii ssp. bulgaricus (37 à 42°C). Cependant, une incubation à des températures sub-
optimales n'a pas changé le rendement de la production des EPS avec des bactéries
lactiques thermophiles (Sebastiani et Zelger 1998). Dupont et al. (2000) et Macedo et al.
(2002a) ont varié la température des cultures de Lb. rhamnosus RW-9595M (32 et 37°C et
dans l'intervalle 22-42°C, respectivement) dans des milieux différents. Les deux études
n'ont pas trouvé un effet significatif de la température sur la production d'EPS.
Il a été montré qu'un contrôle du pH de la culture augmente la production d'EPS comparé à
des conditions acidifiantes (De Vuyst et al. 1998; Gassem et al. 1997a; Grobben et al.
1998; Grobben et al. 1995; Mozzi et al. 1996b). Souvent, le pH optimal pour la production
d'EPS est proche de celui pour la croissance (Gamar-Nourani et al. 1998; Grobben et al.
1998; Mozzi et al. 1994; Mozzi et al. 1996b; Petry et al. 2000). Un ajustement périodique
du pH à une valeur de 6.2 lors des fermentation en batch avec Lb. delbrueckii ssp.
bulgaricus a augmenté la production des EPS, mesurée par la viscosité du milieu (Gassem
et al. 1997a). Lors d'une fermentation en continu (Gassem et al. 1997b), ce résultat a été
confirmé avec un pH de 6.5 favorisant la production d’EPS (comparé à un pH de 5.2 et de
5.8). Mozzi et al. (1996b) ont trouvé une production d’EPS considérablement plus élevée
pour Lb. casei CRL 87 avec un pH contrôlé, comparée à une culture sans contrôle du pH.
Le pH optimal pour la production d'EPS (488 mg/l) a été de 6.0 tandis que le pH optimal
pour la production spécifique (3.9 · 10-5 g EPS/g poids sec des cellules) a été de 4.0. De
plus, pour des cultures de Lb. sake 0-1, il a été observé qu'un pH plus bas (5.8) favorise la
production d'EPS, tandis qu'un pH plus élevé stimule plutôt la croissance de la souche (van
den Berg et al. 1995).
L'aération du milieu pendant la culture n'est pas nécessaire pour la production d'EPS par les
LAB. Au contraire, il semble qu'une basse tension en oxygène stimule la production (De
Vuyst et al. 1998; Looijesteijn et Hugenholtz 1999). Gamar-Nourani et al. (1998) ont
identifié une concentration d'O2 de 10% comme étant optimale pour la production d'EPS
par Lb. rhamnosus C83. Pham et al. (2000) ont étudié l'effet de l'oxygène sur la production
d'EPS par Lb. rhamnosus R. Des concentrations en oxygène basses (jusqu'à 20%) ont
29
augmenté la croissance et la production d'EPS. Cependant, la production spécifique a été
plus élevée pour des conditions anaérobe et aérobe. Les auteurs ont conclu que des
conditions de stress ont induit la production d'EPS.
Somme toute, il est à conclure que les effets des conditions de culture sur la production
d'EPS sont spécifiques pour chaque cas étudié. Les conditions de culture optimales sont à
déterminer pour chaque souche.
1.2.6 Méthodes d'analyse des EPS
1.2.6.1 Quantification
Traditionnellement, la mesure de la viscosité du milieu fermenté a été utilisée pour estimer
la production d'EPS d'une souche dans un milieu liquide (Cerning et al. 1986; Cerning et
al. 1988). Cependant, cette valeur n'est pas nécessairement corrélée avec la quantité d'EPS
produite (Sebastiani et Zelger 1998) (voir aussi chapitre 1.2.2.1) et est fonction des
interactions des EPS avec d'autres constituants du milieu. Ces interactions sont de nouveau
fonction de plusieurs facteurs comme le pH, la température et la force ionique du milieu.
Pour estimer la quantité d'EPS dans un milieu fermenté, il faudrait alors utiliser une
méthode de dosage spécifique. Cependant, une telle méthode n'existe pas. Différents
composants du milieu interfèrent avec la plupart des méthodes de dosage. Dans la plupart
des cas, une étape de purification avant le dosage est alors indispensable. L'isolement et la
purification de l'EPS produit dans un milieu complexe tel que le lait ou le lactosérum est
difficile à cause de la viscosité élevée du milieu fermenté, des faibles quantités d'EPS et de
la contamination par les protéines du lait. La première étape de purification est souvent une
centrifugation, afin de séparer les cellules du milieu. Cependant, la viscosité élevée
empêche souvent une sédimentation des cellules et rend la séparation plus difficile (Cerning
1990). L'addition d'un solvant organique au surnageant résulte en une précipitation de
toutes les macromolécules, incluant les EPS de la solution. La précipitation avec l’éthanol
s’est établie comme la méthode standard d’extraction des EPS. Il est aussi possible
d’utiliser d’autres solvants polaires de faible poids moléculaire tels que le méthanol,
l'acétone et le propane-2-ol, mais leur utilisation n’est pas compatible avec l’usage dans
30
l’industrie agro-alimentaire. L'ajout de sels peut aider à la précipitation d'un EPS chargé
(De Vuyst et Degeest 1999b). Cette étape permet d'augmenter la concentration en EPS et de
diluer les molécules de petite taille, notamment les mono- et disaccharides interférant avec
le dosage d'EPS. Une élimination complète de ces molécules est souvent obtenue par une
dialyse (Cerning 1994; Cerning et al. 1992; De Vuyst et Degeest 1999b; Grobben et al.
1995; Marshall et al. 1995). Surtout si un milieu de culture complexe comme le lait est
utilisé, l'EPS partiellement purifié est souvent encore contaminé par la partie protéique du
milieu et une précipitation avec l'acide trichloroacétique (TCA) est nécessaire (Macura et
Townsley 1984). Comme alternative, une hydrolyse des protéines avec des enzymes
protéolytiques est une bonne option pour éliminer les protéines contaminantes (Bouzar et
al. 1996; Bouzar et al. 1997; Yang et al. 1999). Gancel et Novel (1994) ont, par exemple,
ajouté la pronase pour hydrolyser les polypeptides. Un traitement avec des enzymes tels
que la désoxyribonucléase, la trypsine, la pronase et la protéinase K a aussi été
recommandé par Cerning (1990). Une fois l'EPS purifié, il est souvent concentré par
lyophilisation.
En raison de la longue durée et d'une faible exactitude des méthodes de purification
habituelles, plusieurs méthodes alternatives ont été proposées. Par exemple, Nakajima et al.
(1990) ont utilisé l'ultrafiltration pour la séparation et la récupération d'un
phosphopolysaccharide d'une souche de L. lactis ssp. cremoris. Toba et al. (1992) ont
présenté une méthode de purification partielle et de dosage d'un EPS par une méthode
d'ultrafiltration à petite échelle.
Le dosage des EPS (partiellement) purifiés peut se faire par simple gravimétrie (De Vuyst
et al. 1998) ou par des méthodes colorimétriques. Un dosage gravimétrique nécessite
cependant une purification complète de la poudre d'EPS, tandis que les méthodes
colorimétriques sont plus spécifiques. Le dosage des sucres totaux par la méthode phénol-
acide sulfurique (Dubois et al. 1956) est très fréquemment utilisée. Cette méthode a
l'avantage d'être très sensible et de détecter de façon fiable des sucres dans une solution
avec des concentrations aussi faibles que 10 mg/l, mais elle n'est pas spécifique pour les
EPS et détecte tous les saccharides ainsi que leurs dérivés méthyle-éthers, d'où l'importance
d'une bonne purification de l'EPS. Un autre désavantage de la méthode résulte d'une
31
différence de la réponse colorimétrique en fonction du sucre analysé. Cependant, la
composition exacte de l'EPS en monomères saccharidiques n'est pas toujours connue. C'est
pourquoi le glucose est souvent utilisé pour faire la courbe étalon. L'erreur résultant de la
réponse différente des monomères comme le rhamnose est acceptée et les résultats sont
exprimés en équivalent glucose.
En résumé, plusieurs méthodes différentes de dosage des EPS sont utilisées dans la
littérature, avec des résultats quelquefois questionnables (De Vuyst et Degeest 1999b). Les
diverses équipes de recherche utilisent souvent des protocoles adaptés à la souche étudiée et
au milieu de culture utilisé, avec des rendements en EPS différents. L'incohérence dans les
résultats de quantification d'EPS rend une comparaison de la production par diverses
souches très difficile. De plus, les méthodes nécessitent souvent une étape de purification
partielle de l'EPS laborieuse et de longue durée (10 jours) qui requiert un volume important
de milieu fermenté (100 ml). Un tel volume d'échantillonnage limite fortement la fréquence
des prises d'échantillons et le nombre de répétitions de la mesure par échantillon. Il est alors
primordial de développer une méthode rapide, exacte et reproductible de dosage d'EPS qui
nécessite seulement un petit volume d'échantillon. Dans ce but, nous avons testé dans le
Chapitre 2 une nouvelle méthode de purification partielle d'EPS avec des cellules
d'ultrafiltration agitées.
Récemment, dans notre équipe de travail, une méthode de quantification de l'EPS produit
par Lb. rhamnosus RW-9595M dans le milieu SWP par spectroscopie en proche infrarouge
(NIRS) a été mise au point (Macedo et al. 2002c). Cette méthode a permis de doser
simultanément l'EPS, l'acide lactique et le lactose directement dans le milieu de
fermentation, sans aucun traitement préalable du milieu. Le spectre obtenu par NIRS a été
calibré avec des mesures de la concentration d'EPS, prises avec la nouvelle méthode
d'ultrafiltration, mentionnée auparavant et développée dans le Chapitre 2, et un coefficient
de corrélation de 91% a été calculé. Cette étude a montré que la méthode NIRS peut être
utilisée pour prédire simultanément, en moins de 5 min, les concentrations de plusieurs
substances, entre autre d'EPS, pendant une fermentation avec des bactéries lactiques.
Cependant, la mesure a été affecté par des nombreuses paramètres du milieu ce qui a limité
l'exactitude de la calibration de la méthode.
32
1.2.6.2 Caractérisation physico-chimique
Afin d'élucider la composition et la structure de la molécule d'EPS, un très haut degré de
pureté est requis et plusieurs techniques de purification ont été développées à cet effet ces
dernières années. Tuinier et al. (1999b) ont mis au point un protocole de purification de
l'EPS de L. lactis ssp. cremoris NIZO B40 impliquant plusieurs étapes de filtration avec des
membranes ayant différents seuils de coupure et ont examiné les propriétés physiques de
l'EPS purifié.
Pour analyser chimiquement les monomères, on est obligé d’hydrolyser le polysaccharide
en utilisant un acide concentré et des températures élevées. Parce que les monosaccharides
n’ont pas tous la même résistance aux conditions d’hydrolyse, il faut contrôler les
conditions avec précision jusqu’à la conversion totale de l'EPS. On peut ensuite déterminer
la composition des EPS en utilisant différentes méthodes. L’identification des monomères
peut être réalisée par des méthodes enzymatiques, spectrophotométriques, par la
chromatographie liquide haute performance (HPLC), la chromatographie en phase gazeuse
(GLC) ou avec la spectrométrie de masse.
En raison du grand nombre de liaisons et de configurations possibles dans la formation des
EPS, il peut y avoir un grand nombre de structures et de propriétés résultantes. Chaque
hexose peut être lié en α ou β, dans la forme pyranose ou furanose et lié à la 2ième, 3ième,
4ième ou 6ième position. Le poids moléculaire peut être déterminé par des méthodes
chromatographiques. La méthode HPLC couplée avec la technique de perméation de gel est
couramment utilisée (Tuinier et al. 1999b; Van Calsteren et al. 2002), mais aussi les
techniques d'électrophorèse, et de chromatographie en phase gazeuse (GLC) (Knoshaug et
al. 2000; Lemoine et al. 1997; Looijesteijn et Hugenholtz 1999; Low et al. 1998; Van
Calsteren et al. 2002; Van Casteren et al. 1998). Pour l'identification des monomères de
l'EPS, la méthode classique est la méthylation suivie de l’hydrolyse, de l’identification et de
la quantification, par GLC, des sucres partiellement méthylés (Sutherland 1990). Cette
procédure donne des informations sur la taille et la structure des monomères.
Récemment, la technique de la résonance magnétique nucléaire (RMN) a permis de faire
des progrès considérables dans l'élucidation de la structure des EPS. En combinaison avec
33
l'analyse chimique, il est possible d'identifier par les spectres 1H-, 13C-et 31P-RMN les
substances présentes et leurs liaisons chimiques et ainsi la structure primaire de l'EPS. Avec
une biomasse assez importante dans le RMN, il est même possible d'obtenir sans détruire
l'échantillon des informations in vivo sur la formation des EPS. De cette façon, Hugenholz
et al. (2000) ont pu suivre l'évolution des intermédiaires clés de la formation d'EPS par une
souche EPS+ de Lactococcus lactis et les comparer avec une souche isogénique non-
productrice.
Van Calsteren et al. (2002) ont isolé et purifié les EPS de Lb. rhamnosus RW-9595M et de
Lb. rhamnosus R et les ont analysés par 1H- et 13C-RMN. Les spectres obtenus, et
conséquemment les EPS des deux souches, ont été identiques. Par la suite, les auteurs ont
déterminé la masse moléculaire de l'EPS par chromatographie de perméation sur gel et ont
élucidé la structure primaire de l'EPS par des méthodes chimiques et spectroscopiques afin
de confirmer les résultats obtenus par la RMN. Sur la base de ces analyses, l'unité répétitive
de l'EPS a été déterminée comme étant un heptasaccharide avec un pyruvate, deux D-
glucose, un D-galactose, et quatre L-rhamnose (Fig. 1.2).
1.2.6.3 Production à grande échelle et traitement en aval
La production d'EPS par les LAB étant limitée, il y a très peu d'études portant sur la
production à plus grande échelle. Ces EPS n'étant pas (encore) rentables comme ingrédient
pour l'industrie agro-alimentaire, la plupart des études se sont concentrées sur la production
d'EPS in situ dans les aliments fermentés. Kimmel et al. (1998) ont optimisé la production
d'EPS de Lb. delbrueckii ssp. bugaricus RR et ont réalisé une culture à pH contrôlé avec un
volume de 100 l dans un milieu semi-défini. Les auteurs ont concentré les EPS du milieu
fermenté avec une ultrafiltration et éliminé les matériaux ayant un faible poids moléculaire
par une dialyse avant la précipitation avec l’éthanol. Malgré cela, la poudre d'EPS contenait
1.4% de protéines et, en plus, les auteurs ont supposé une perte importante d'EPS lors de la
précipitation avec l'éthanol. Une récupération de seulement 30 g d'EPS purifié a été
mesurée suite au traitement des 100 l fermentés. Afin de diminuer la perte du produit
pendant le procédé, les auteurs recommandent la récupération du polymère par des
techniques de filtration. Un tel processus de traitement en aval du milieu fermenté pour la
34
récupération des EPS produits par les LAB pourrait s'inspirer des techniques utilisées dans
la fabrication du xanthane. L'ultrafiltration est utilisée pour la concentration du xanthane
dans le milieu fermenté (de 2.5 à 15% p/v), avant l'étape de précipitation par l'éthanol. Ceci
permet de réduire le volume d'alcool et ainsi la quantité d'énergie utilisée pour la
récupération de l'éthanol d'environ 80% (Lo et al. 1997). Des techniques de filtration ont
aussi été utilisées avec succès pour la récupération d'EPS produit par Sinorhizobium
meliloti M5N1 CS (Harscoat et al. 1999).
1.2.7 Utilisation et applications des hétéropolysaccharides
En examinant les procédés de production des yoghourts, on remarque que la production a
beaucoup changé ses dernières dizaines d'années. Sa rentabilité a augmenté avec la mise en
marché des procédés semi-continu. C’est ainsi que la production traditionnelle avec une
fermentation dans le pot n’occupe plus une part importante du marché actuel (Cerning
1990). Les nouveaux produits comme les yoghourts avec des fruits, les yoghourts
aromatisés ou les yoghourts buvables sont presque tous produits à grande échelle, donc
agités et transportés avant leur soutirage. Puisque le yoghourt perd en partie sa texture
pendant ces traitements mécaniques, on est obligé d’en augmenter la viscosité. La plupart
des producteurs utilisent à cette fin des méthodes comme l'augmentation des solides totaux
du lait standardisé, le traitement à la chaleur avant inoculation ou l'addition de
stabilisateurs. Ceci implique une augmentation des coûts considérable ce qui rend la
production des hétéropolysaccharides in situ par les LAB très intéressante (Bouzar et al.
1997; Marshall et Rawson 1999; Rawson et Marshall 1997).
L’utilisation d’EPS dans l’industrie laitière est basée principalement sur les aptitudes
épaississante, gélifiante, stabilisante et émulsifiante de ces composés. Ils jouent donc un
rôle important dans la formation de la texture des aliments. Les bactéries lactiques
mésophiles et thermophiles sont employées pour améliorer le comportement rhéologique
des laits fermentés et des yoghourts. Ces souches offrent la possibilité d’augmenter la
viscosité du yoghourt et de diminuer la susceptibilité à la synérèse ce qui est
particulièrement intéressant pour les pays interdisant l’addition des gélifiants ou
épaississants aux laits fermentés. En outre, ceci permet de diminuer la teneur en solides
35
totaux du lait standardisé pour la fabrication de yoghourt, tout en conservant des propriétés
rhéologiques et organoleptiques comparables aux yoghourts témoins produits avec des
cultures non épaississantes et enrichis en solides du lait. De plus, en employant les EPS des
LAB comme bioingrédients fonctionnels dans les produits laitiers pour remplacer des
agents polysaccharidiques d’autres origines (carraghénanes, alginates, xanthanes), on peut
produire des produits plus naturels et ainsi répondre à une demande des consommateurs
pour des produits sans additifs.
En employant des bactéries lactiques épaississantes productrices d’EPS, il est possible de
produire des fromages allégés. Par exemple, l'utilisation d'une souche de S. thermophilus
productrice d'EPS et de Lb. bulgaricus a permis de produire un fromage mozzarella allégé
avec des propriétés améliorées de fusion et de rétention de l’humidité (Low et al. 1998;
Perry et al. 1998; Perry et al. 1997). Une autre application possible des LAB productrices
d'EPS est leur utilisation dans le levain. Les EPS aident à ramollir le gluten et ainsi à
améliorer la texture du levain et à augmenter le volume spécifique du produit boulanger
(De Vuyst et al. 2001).
Appartenant à la classe des fibres alimentaires, les EPS peuvent servir de substituts à basse
teneur en calories pour remplacer le gras. C’est ainsi qu’on peut produire des aliments avec
moins de gras et de solides totaux, mais avec des propriétés organoleptiques comparables
aux produits traditionnels. De cette façon, les EPS pourraient contribuer à offrir une source
d’aliments plus sains aux consommateurs.
1.3 Technologie des cellules immobilisées
La technologie des cellules immobilisées (ICT) n’est pas récente. C'est un procédé
traditionnel utilisé, par exemple, dans la production du vinaigre par des bactéries acétiques
immobilisées sur des copeaux de bois (Ramakrishna et Prakasham 1999) ou dans la
production du Kéfir avec des levures coimmobilisées avec des bactéries lactiques
(Champagne et al. 1994). L'immobilisation permet de retenir les cellules microbiennes dans
un système de fermentation et d'obtenir des hautes densités de biomasse. Cette technique
comporte de nombreux avantages, mais aussi des inconvénients, comparé à des procédés
utilisant des cellules libres (Tab. 1.2). Les avantages majeurs sont, sans doute, une
36
productivité augmentée de la fermentation et une rétention des cellules, même à de hauts
taux de dilution (Champagne et al. 1994). D'autres avantages sont une réutilisation possible
des cellules, une protection contre des forces de cisaillement et une stabilité biologique
élevée, lors de fermentations en continu (Lamboley et al. 1999). De plus, il est possible que
les systèmes avec des cellules immobilisées soient moins susceptibles aux attaques des
bactériophages (Champagne et al. 1994) et à la contamination microbienne (Navrátil et
Sturdíc 1999).
La haute densité cellulaire et un micro-environnement différent des conditions dans le
milieu de culture résultent souvent en un changement morphologique et physiologique de la
culture (voir chapitre 1.3.4). Ceci peut représenter un avantage, par exemple en augmentant
la tolérance de la souche envers des substances inhibitrices ou en découplant la croissance
bactérienne de la production de métabolites (Norton et al. 1994a), ou un désavantage car le
métabolisme pourrait être modifié de façon non voulue.
37
Tab. 1.2 Avantages et désavantages de la technologie des cellules immobilisées.
AVANTAGES • Productivité augmentée à cause d’une
densité de biomasse plus élevée • Lavage de la biomasse du réacteur
empêché pendant la fermentation continue, même avec un taux de dilution élevé
• Stabilité biologique et physique des cellules plus élevée en raison de la protection par le support
• Découplage de la croissance et de la production de métabolites
• Coût réduit pour le traitement en aval du milieu
• Rendements plus élevés pour la production de métabolites secondaires
• Rétention élevée des plasmides chez les cellules qui en possèdent
• Protection contre certains effets inhibiteurs dans le milieu
• Susceptibilité diminuée contre l'attaque des phages et des contaminants
• Métabolisme peut être modifié par l’immobilisation
DÉSAVANTAGES • Cellules peuvent se séparer du support
et ainsi contaminer le produit • Stabilité mécanique et chimique de
certains supports peut être insuffisante (cisaillement, dissolution, décompo-sition par le produit)
• Prolifération cellulaire peut détruire la matrice du support et les cellules se libèrent par la suite
• Limitations de diffusion peuvent restreindre la bioconversion
• ICT peut être trop chère pour une utilisation à grande échelle
• Métabolisme peut être modifié par l’immobilisation
• Nécessite d'ajouter une étape de production des cultures immobilisées au procédé
• Nécessite d'entreposer les cellules ou de prévenir leur mortalité lors des périodes d'arrêt de production
• Complexité de l'assainissement du bioréacteur si des contaminations se produisent
1.3.1 Techniques et procédures d'immobilisation
En raison des avantages importants de l'ICT, comparé avec des cultures utilisant des
cellules planctoniques, plusieurs techniques d'immobilisation ont été développées. Toutes
ces techniques imitent ce qui se passe dans la nature, où les cellules des microorganismes
croissent presque toujours dans un biofilm, associées entre elles et avec des surfaces
(Dunne 2002). Afin d'immobiliser des cellules, on peut les attacher à des surfaces, les
inclure dans des matrices poreuses, les retenir derrière des barrières ou les faire floculer
(Fig. 1.6). Nous avons concentré notre travail sur les systèmes dans lesquels les cellules
sont immobilisées par adhésion ou inclusion. Les systèmes où les cellules sont
immobilisées derrière une barrière (ex. réacteurs avec membrane) et ceux où la barrière est
formée autour des cellules (ex. microcapsules) présentent souvent des problèmes de
38
transfert de matière et d'encrassement des membranes (Gonçalves et al. 1992) et ne
semblent pas être adéquats pour l'immobilisation des cellules productrices d’EPS.
Adsorptionnaturelle
Adsorptioninduite
artificiellement
Attachées à la surface
Inclusiondans gel
Supportpréformé
Inclusion dansdes matrices poreuses
Immobilisationderrière une barrière
Aggrégationnaturelle
Aggrégationinduite
artificiellement
Floculation
Cellules immobilisées vivantes
Fig. 1.6 Classification des systèmes d’immobilisation selon quatre classes (adapté de
Willaert et Baron 1996).
L’immobilisation des cellules peut être réalisée par adhésion à la surface de différents
supports. Dans cette étude, ce procédé a été choisi en raison du caractère mucoïde de la
souche de travail, Lb. rhamnosus RW-9595M. La production par les cellules de
polysaccharides capsulaires et d'EPS libre contribue à l'adsorption au support et à sa
colonisation subséquente (Dunne 2002). Les forces participant à l'adhésion d'une cellule au
support sont la force de Van der Waals, les liaisons ioniques, les ponts hydrogènes et les
interactions covalentes. Pour comprendre les mécanismes de l’adsorption microbienne, la
structure de la paroi cellulaire doit être connue. La distribution des groupes carboxyliques
et aminés dans les composantes de la paroi déterminent la charge de la cellule. En général,
la plupart des microorganismes sont chargés négativement. Également, un grand nombre
d'EPS et ainsi de capsules portent une charge légèrement négative. Pour cette raison, il est
préférable d’utiliser des supports chargés positivement.
Un autre moyen d’immobilisation est l’inclusion des cellules dans une matrice poreuse qui
peut être soit un gel, soit un support préformé. Dans le premier cas, la matrice poreuse est
formée in situ autour de la cellule. Avec cette technique, les cellules sont incluses dans un
polymère. Ensemble, ils forment le biocatalyseur avec lequel la fermentation est exécutée.
Ce biocatalyseur est souvent obtenu par dispersion d'une solution de polysaccharides et/ou
de protéines contenant les cellules et ensuite par solidification de cette solution. La
dispersion peut être réalisée par extrusion ou par émulsification. Une bonne vue d’ensemble
39
de ces procédés est donnée par Groboillot et al.(1994), Champagne et al. (1994) et de
Prenosil et al. (1995).
Dans le cas d’un support poreux préformé, on ajoute la matrice d'immobilisation au début
d’une fermentation. On laisse diffuser les cellules dans les espaces libres du support où
elles commencent à proliférer. Puisque la croissance des colonies est rapidement limitée par
le support et les colonies voisines, elles sont alors retenues dans le biocatalyseur (Karel et
al. 1985). Afin d'obtenir des biomasses immobilisées élevées, les surfaces intérieures ainsi
qu'extérieures doivent être accessibles pour les cellules et les supports avec une porosité
élevée sont les plus appropriés. Au début, les forces d'adhésion décrites précédemment,
déterminent la vitesse de la colonisation du support. Quand les premières cellules sont
adhérées et les colonies se sont formées, le diamètre des pores du support devient
important. Il existe une grandeur idéale de pores qui est déterminée par un équilibre entre
deux effets: les pores doivent être assez grands pour permettre la pénétration et la
croissance des cellules à l’intérieur de la matrice, mais ils doivent être assez petits pour
empêcher la perte des cellules en croissance (Prenosil et al. 1995). Messing et al. (1979a;
1979b) ont déterminés la grandeur optimale des pores pour plusieurs microorganismes. Ils
ont trouvé un rapport optimal pour les bactéries de 4 à 5 entre la taille du pore et celle de la
cellule. L'utilisation des supports avec des pores plus grands que 100 µm représente une
forme d'immobilisation se situant entre la floculation et l'inclusion (Karel et al. 1985).
La matrice préformée protège les cellules contre les forces de cisaillement à l’extérieur du
biocatalyseur tout en permettant une bonne diffusion des nutriments et des produits
métaboliques (De Backer 1996). Ce procédé d'immobilisation n’est pas nuisible pour la
prolifération des cellules, comme ça peut être le cas pour certaines techniques d’inclusion
dans des billes de polymères formées in situ. Cependant, les densités de cellules sont en
général moins élevées qu’avec l’inclusion in situ (Klein et Vorlop 1985). En raison de la
forte résistance du support à la compression, cette méthode d’immobilisation est adéquate
pour l’utilisation dans des réacteurs comme le réacteur agité ou le réacteur de type lit fixe.
Les supports solides sont en général physiquement et chimiquement résistants envers
l'usure par la croissance des microorganismes, ils sont souvent stérilisable par la vapeur et
réutilisable. La simplicité du procédé et le faible coût rendent l'immobilisation par
40
adsorption sur des supports solides poreux très intéressante pour l’application industrielle.
Dans ce travail, la souche Lb. rhamnosus RW-9595M a été immobilisée par adsorption sur
des supports poreux solides, car son caractère mucoïde favorise fortement son adhésion aux
surfaces.
1.3.2 Choix du support
Pour l'utilisation de l'ICT dans l'industrie agroalimentaire, il existe des exigences
concernant la nature du support. Premièrement, il ne doit pas être toxique, ni pour l’homme
ni pour les bactéries, et son utilisation dans le domaine alimentaire doit être permis. En
outre, il doit montrer des propriétés physiques et chimiques favorisant l’immobilisation. Un
support préformé est caractérisé par sa densité, sa taille et sa forme, sa résistance à la
friction, sa capacité de rétention des cellules (diamètre des pores et porosité) et sa charge de
surface. De plus, il doit être stérilisable.
Le Tab. 1.3 donne une vue d'ensemble sur les matériaux de supports poreux solides
rapportés en littérature. Par exemple, Senthuran et al. (1997) ont choisi des billes de verre
(foam-glass-particles, Pora-bact A®) pour immobiliser Lb. casei. Ils ont comparé ce
matériel avec les mêmes billes prétraitées avec du polyéthylèneimine et ont constaté, d’une
part, un rallongement de la phase de latence et, d’autre part, une rétention des cellules
améliorée. Gonçalves et al. (1992) ont comparé des supports inertes en verre et en
céramique en utilisant un réacteur en régime turbulent en continu avec recyclage. Les
supports se sont distingués quant à la densité, au diamètre des particules, et des pores et à la
porosité. Les auteurs ont observé un meilleur attachement en conduisant des fermentations
en continu, comparé avec un procédé en batch et ont identifié un support en verre
aggloméré (Sikug) et un support en céramique (Bi86) comme étant les supports avec la
capacité de rétention de biomasse la plus élevée.
41
Tab. 1.3 Immobilisation par inclusion dans des supports solides poreux.
Matériel du support Microorganisme Référence cellulose Saccharomyces cerevisiae (Szajani et al. 1996) cubes d'éponge Aureobasidium pullulans (West et Strohfus 1996)
(Ho et al. 1997) plastique composite (50% polypropylène) Lactobacillus casei (Velazquez et al. 2001)
Leuconostoc mesenteroides (El-Sayed et al. 1990) Xanthomonas campestis (Robinson et Wang 1987) Celite Aureobasidium pullulan (Mulchandani et Luong 1989)
chitosane calcium pectate Lactobacillus casei (Kosseva et al. 1998)
"type-Z" Celite R635 Flexirings
Pseudomonas aeruginosa (Durham et al. 1994)
fibre de verre et polyester céramique mouse de polyuréthane
Aureobasidium pullulan (Mulchandani et Luong 1989)
aluminium bactéries lactiques (Iwasaki et al. 1992) polypropylène traité avec chitosane Lactobacillus plantarum (Krishnan et al. 2001)
Lactobacillus casei (Senthuran et al. 1997) verre Lactobacillus rhamnosus (Gonçalves et al. 1992)
céramique Lactobacillus rhamnosus (Gonçalves et al. 1992) Leuconostoc mesenteroides (El-Sayed et al. 1990) acier inoxydable Trichoderma viride (Webb et al. 1986)
caoutchouc de silicone Saccharomyces cerevisiae (Knights 1996)
Il y a peu de travaux dans la littérature sur la production d'EPS avec des cellules
immobilisées, la plupart portant sur la production des homopolysaccharides (impliquant des
enzymes extracellulaires). Par exemple, le pullulane a été produit par la moissisure
Aureobasidium pullulans immobilisée par inclusion dans des cubes d'agar ou de calcium
alginate (West et Strohfus 1998; West and Strohfus 2001), dans des billes de gel d'agarose
et de carraghénane (West 2000) et dans des cubes d'éponge (West et Strohfus 1996). Lors
de deux fermentations en batch successives, les auteurs ont trouvé des productions d'EPS
plus élevées pour les cultures immobilisées qu'avec des cellules libres. El-Sayed et al.
(1990) ont comparé la production de dextrane et de dextranesucrase par Ln. mesenteroides
immobilisée dans trois types de supports Celite de différents diamètres et tailles de pores et
42
dans des billes de gel d'alginate de calcium. Les auteurs ont trouvé la production de
dextranesucrase la plus élevée avec le support Celite R648, qui était 64% supérieure à celle
des cultures avec des cellules libres. Robinson et Wang (1987) ont aussi utilisé le support
Celite pour immobiliser la bactérie Xanthomonas campestris pour la production de
xanthane dans un réacteur de 16 l. Les auteurs ont observé une forte rétention du
biopolymère dans la matrice d'immobilisation qui a atteint une concentration de 50 g/l.
Le support solide poreux ImmobaSil® utilisé dans cette thèse pour l'immobilisation de
Lb. rhamnosus RW-9595M est fait en caoutchouc de silicone. Il est disponible dans une
forme d'anneau appelé Raschig Ring et offre une taille de pores uniforme de 50 à 150 µm et
une fraction vide d'environ 40%.
1.3.3 Analyse des cellules immobilisées
Afin d'élucider les effets de l'immobilisation sur les cellules, des techniques d'analyse du
système à cellules immobilisées, idéalement non-destructives, sont nécessaires. Il y a
maintenant plusieurs techniques biophysiques disponibles et l'instrumentation pour diverses
techniques spectroscopiques s'améliore constamment. Les mesures d'intérêt dans l'examen
des systèmes avec cellules immobilisées sont, par exemple, la concentration des cellules
immobilisées et les cinétiques de croissance, de consommation de substrat et de formation
de produits. Une caractérisation morphologique et physiologique des cellules immobilisées,
de même que de leur environnement direct, est aussi d'un grand intérêt. Les méthodes
comme la microscopie optique et électronique, le marquage avec des radioisotopes et
l'autoradiographie, la microfluorimétrie, la spectroscopie infrarouge et la résonance
magnétique nucléaire (RMN) peuvent être utilisées pour étudier des cellules immobilisées
(Clark 1989).
La RMN est un outil très puissant pour suivre les processus métaboliques des cellules
immobilisées. Cette méthode est non-destructive et a été utilisée, par exemple, pour
comparer le métabolisme de levures (Lohmeier-Vogel et al. 1995; 1996; Taipa et al. 1989)
et de propionibactéries (Santos et al. 1989) libres et immobilisées. La 31P-RMN permet de
mesurer le pH intracellulaire, les sucres phosphatés, l'ADP et l'ATP tandis que la 13C-RMN
peut donner des informations sur le métabolisme des sucres (Lohmeier-Vogel et al. 1989).
43
Avec la RMN il est aussi possible de mesurer la quantité des cellules immobilisées (Clark
1989), mais l'application de cette méthode est très limitée à cause de son coût élevé, des
interférences avec le support et le milieu, un équipement sophistiqué et dispendieux et une
mise au point de méthode très longue.
La quantité de biomasse est un paramètre très important pour l'analyse et le contrôle d'un
système de fermentation. Cependant, la quantification précise de la biomasse immobilisée
peut être très difficile, surtout si elle est immobilisée sur des supports solides et poreux
(Wang 1988). Si les cellules sont incluses dans des billes de gel, la matrice du support est
communément détruite ou dissoute et les cellules vivantes sont ensuite comptées. Pour des
supports solides, cette méthode ne peut pas être utilisée car la destruction du support
résulterait en un stress mécanique trop grand pour les cellules et, conséquemment, en un
taux de mortalité des cellules élevé. Un autre moyen de quantifier la biomasse immobilisée
est la mesure de la différence de poids du support avant et après colonisation. Cette
technique est très souvent utilisée pour des supports solides (Gonçalves et al. 1992;
Senthuran et al. 1997), mais elle a le désavantage de doser également les substances
accumulées dans la matrice du support pendant la fermentation, comme, par exemple, les
EPS. De plus, cette méthode donne seulement une information sur la biomasse totale, sans
tenir compte de sa viabilité, et dose alors aussi la biomasse morte. Comme l'immobilisation
cellulaire résulte souvent en un changement majeur de la taille des cellules immobilisées
(voir chapitre 1.3.4), avec des cellules immobilisées généralement plus petites que leur
contre-parties planctoniques, la valeur de biomasse des cellules immobilisées ne peut pas
estimer précisément le nombre de cellules vivantes, en utilisant une courbe de calibration
déterminée avec des cultures planctoniques.
La spectroscopie diélectrique et la résonance magnétique nucléaire sont deux méthodes
non-destructives pouvant servir à doser des cellules microbiennes immobilisées, déjà
mentionnées et discutées auparavant. Ces méthodes permettent de suivre la biomasse en
ligne. La spectroscopie diélectrique se base sur la mesure de la capacitance qui est une
fonction de la concentration des cellules microbiennes dans un champs électrique. Elle est
surtout appliquée dans la fabrication de la bière pour le contrôle de biomasse de la levure
(Austin et al. 1994). Un avantage de cette méthode est qu’elle n’est pas influencée par la
44
présence de solides dans le champs électrique, ce qui la rend particulièrement intéressante
pour des systèmes avec des cellules immobilisées. Cependant, il y a des difficultés à utiliser
cette méthode pour la mesure de la concentration en bactéries, car sa sensibilité est
directement proportionnelle à la grandeur (le volume) des cellules. Mishima et al. (1991)
ont ainsi mesuré, entre autres, la concentration de Saccharomyces cerevisiae, incluse dans
des billes de calcium alginate, et de cellules libres de Escherichia coli.
Un autre moyen de quantifier les cellules immobilisées est le dosage d'un de leurs
composants. Ce composant doit être spécifique pour des microorganismes et ne pas se
trouver dans le support non-colonisé, comme les protéines (Moreira et al. 1978; Robinson
et Wang 1987), l'adénosine triphosphate (ATP) (Gikas et Livingston 1993; 1998) et l'acide
désoxyribonucléique (ADN) (Buchtmann et al. 1997; Raebel et Schlierf 1980; Wang 1988;
Wang et Wang 1989). Si la quantité d'un composant par unité de biomasse ou par cellule
est connue, le contenu de ce composant dans un support peut être mesuré et corrélé avec le
contenu en cellules immobilisées. Cette approche a été testée pour les protéines, l'ATP et
l'ADN et les résultats sont discutés au Chapitre 3.
1.3.4 Effets physiologiques et morphologiques de l'immobilisation
L'immobilisation cellulaire résulte pour les bactéries immobilisées en des conditions
environnantes différentes de celles des cellules planctoniques. Une limitation du transfert
de masse crée un micro-environnement autour des cellules affectant la diffusion de
nutriments vers la cellule mais aussi l'élimination des produits comme l'acide lactique
(Champagne et al. 1994). Les propriétés du support, les conditions hydrodynamiques dans
le fermenteur, mais aussi la production et l’excrétion de substances extracellulaires, en
particulier des EPS, sont des facteurs qui affectent la résistance à la diffusion (Karel et al.
1985). L'accumulation des produits métaboliques peut diminuer le taux de croissance et
changer la physiologie et la morphologie des bactéries lactiques immobilisées (Cachon et
al. 1998; Champagne et al. 1994; Krishnan et al. 2001).
Karel et al. (1985) ont déjà constaté que la voie métabolique des cellules attachées à des
surfaces peut être différente de celle des cellules libres. Des travaux plus récents ont
démontré l'existence de mécanismes de reconnaissance de surface pour les bactéries
45
(Prigent-Combaret et al. 1999; Wen et Burne 2002) et des changements physiologiques dus
à la présence de surfaces (O'Toole et al. 2000a; 2000b; Parsek et Greenberg 2000; Rashid
et al. 2000). Entre-temps, plusieurs travaux ont rapporté de tels changements lors des
fermentations avec des cellules immobilisées, notamment une tolérance accrue envers
l'inhibition par le produit (Fortin et Vuillemard 1989; Krisch et Szajani 1997; Teixeira de
Mattos et al. 1994) ou même envers d'autres facteurs de stress environnementaux (Doleyres
et al. 2002a; Jouenne et al. 1994; Keweloh et al. 1989; Keweloh et al. 1990; Trauth et al.
2001).
1.4 Problématique
Depuis une dizaine d’années, le consommateur a développé son intérêt pour des aliments
naturels, sans additifs et de haute qualité. À cause d’une prise de conscience pour une
alimentation équilibrée, des produits avec un taux de matière grasse moins élevé sont
préférés. De plus en plus, des produits avec une allégation santé et des denrées
fonctionnelles percent sur le marché. Ces dernières années, l’industrie laitière a commencé
à utiliser des bactéries lactiques produisant des exopolysaccharides parce qu’elles
améliorent les caractéristiques rhéologiques des laits fermentés, ce qui permet d'éviter
l’utilisation des additifs épaississants, de réduire la matière grasse dans les produits et
même la teneur en solides du lait pour une même fermeté ou viscosité du produit.
La faible production des exopolysaccharides par les bactéries lactiques et l’instabilité du
phénotype mucoïde est un problème reconnu et la raison pour laquelle, jusqu'à maintenant,
ces EPS sont exclusivement produit in situ dans des produits comme le yogourt ou les laits
fermentés. L’incorporation d'un agent fonctionnel issu des bactéries lactiques permettrait de
standardiser le produit, mais l'exploitation d’une fermentation pour produire des
exopolysaccharides comme bioingrédients fonctionnels sera fortement dépendante du
rendement du procédé. L’immobilisation de la souche est un moyen efficace d'augmenter la
productivité et de stabiliser biologiquement des fermentations en continu. Parce que les
propriétés mucoïdes des souches productrices d'EPS favoriseraient fortement
l’immobilisation par adhésion dans des supports poreux, c'est cette dernière qui est étudiée
dans cette thèse.
46
Le nouveau bioingrédient fonctionnel devra faire face à la concurrence de polysaccharides
d'autres origines comme le xanthane et la gomme de caroube. Afin de rendre les EPS des
bactéries lactiques concurrentiels, il est important de trouver les conditions optimales
(température, pH, taux de dilution) des fermentations en continu avec des cellules
immobilisées pour la production d'EPS. Pour l'optimisation des fermentations, plusieurs
échantillons doivent être pris et la quantité d'EPS doit être déterminée. Cependant, les
méthodes existantes pour l’isolement et la purification des EPS sont de longue durée, et
nécessitent un volume important d'échantillon. Ceci rend la détermination de la quantité et
de la qualité des EPS laborieuse et difficile. Le développement d'une nouvelle méthode
fiable, simple et nécessitant un faible volume d'échantillon pour le dosage des EPS est alors
nécessaire.
Le substrat de la fermentation choisi est à base de perméat de lactosérum, un sous-produit
de l’industrie laitière, contenant la quasi totalité du lactose du lait. Si le perméat de
lactosérum n'est pas traité, il présente une source importante de pollution de l'industrie
fromagère. Il est disponible en grande quantité et de valorisation limitée mais est une
excellente source de carbone et de minéraux pour des fermentations avec des bactéries
lactiques.
La souche Lactobacillus rhamnosus RW-9595M a été choisie comme souche de travail à
cause de ses propriétés technologiques (viscosité, arômes), nutritionnelles (fibre
alimentaire, probiotique) et éventuellement nutraceutiques associées à une forte synthèse
d'EPS. Cette souche a démontré une forte production d'EPS de 2775 mg/l dans un milieu à
base de perméat de lactosérum (Macedo et al. 2002b).
1.5 Hypothèse et objectifs de travail
Jusqu'à maintenant, aucune étude à été réalisée sur la production d'un hétéropolysaccharide
par des bactéries lactiques immobilisées. L'hypothèse que l'immobilisation cellulaire
permettra d'augmenter la productivité en EPS lors des fermentations en batch et en continu
conduit directement à la formulation de l'objectif général de ce travail.
47
1.5.1 Objectif général
L’objectif général de ce travail est de développer et d’optimiser une technologie de
production d'exopolysaccharides, basée sur la fermentation avec des cellules immobilisées,
d’un milieu à base de perméat de lactosérum (PLS).
1.5.2 Objectifs spécifiques
Les objectifs spécifiques sont :
• Développer une méthode précise et rapide de mesure des EPS produits dans le
milieu de fermentation.
• Évaluer l’aptitude de plusieurs supports, compatibles avec une utilisation
alimentaire, pour l’immobilisation par adhésion de Lactobacillus rhamnosus
RW-9595M.
• Développer une méthode précise de dosage des cellules immobilisées dans des
supports solides poreux.
• Exécuter et caractériser des fermentations avec des cellules planctoniques en batch
et en continu pour la production de biomasse, de produits métaboliques et d'EPS
dans le PLS.
• Exécuter et caractériser des fermentations en batch répété et en continu avec des
cellules immobilisées dans le PLS et comparer la production d'EPS avec les
fermentations avec des cellules planctoniques. Lors des fermentations en continu,
nous avons étudié particulièrement l’effet du taux de dilution, de la température et
de la concentration en extrait de levure en rapport avec la cinétique des
fermentations et la productivité en EPS.
Chapitre 2
New method for exopolysaccharide determination in
culture broth using stirred ultrafiltration cells
Dirk Bergmaier1, Christophe Lacroix1, Maria Guadalupe Macedo1 and Claude P.
Champagne2
1 STELA Dairy Research Centre, Pavillon Paul Comtois, Université Laval, Québec, PQ,
Canada, G1K 7P4
2 Food Research and Development Centre, Agriculture and AgriFood Canada, St-
Hyacinthe, PQ, Canada, J2S 8E3
Part of these results were published in Applied Microbiology and Biotechnology 2001, 57
(3), 401-406.
49
2.1 Résumé
Une nouvelle méthode pour éliminer les sucres simples du milieu de culture avant la
quantification des exopolysaccharides (EPS), a été développée et validée pour une souche
productrice d'EPS, Lactobacillus rhamnosus RW-9595M. Cette méthode emploie
l'ultrafiltration (UF) dans des cellules agitées, suivie de la détection des polysaccharides
dans le rétentat par la méthode phénol-acide sulfurique. La méthode UF a été comparée à
une méthode conventionnelle basée sur l'extraction à l'éthanol, la dialyse, la séparation des
protéines par précipitation avec le TCA et la lyophilisation. Des fermentations en batch
avec pH contrôlé dans des milieux divers (le milieu minimum basique (BMM), le perméat
de lactosérum (WP), et le perméat de lactosérum supplémenté avec l'extrait de levure, les
minéraux et le Tween-80 (SWP) ont été conduites et la production d'EPS a été déterminée
par la nouvelle méthode UF et par une méthode conventionnelle. La récupération d'EPS par
la nouvelle méthode a été entre 83 et 104% pour une concentration d'EPS entre 40 et 1500
mg/l supplémenté à une solution de 0.1 M NaCl ou un milieu de culture. La méthode d'UF
était rapide (8 h), précise et simple, et a requis seulement un petit volume d'échantillon (1 à
5 ml). Une production maximale d'EPS très élevée a été mesurée dans le SWP par les
méthodes UF et conventionnelle (1718 et 1755 mg/l).
2.2 Abstract
A new method to remove simple carbohydrates from culture broth prior to the
quantification of exopolysaccharides (EPS) was developed and validated for the EPS-
producing strain Lb. rhamnosus RW-9595M. This method uses ultrafiltration (UF) in
stirred cells followed by polysaccharide detection in the retentate by the phenol-sulfuric
acid method. The UF method was compared to a conventional method based on ethanol
extraction, dialysis, protein removal by TCA and freeze-drying. EPS production during pH-
controlled batch fermentations in basal minimum medium (BMM), whey permeate (WP),
and whey permeate supplemented with yeast extract, minerals and Tween-80 (SWP) was
determined by the new UF and conventional methods. EPS recovery by the new method
ranged from 83 to 104% for EPS added in the concentration range from 40 to 1500 mg/l in
0.1 M NaCl solution or culture medium. The UF method was rapid (8 h), accurate and
50
simple, and required only a small sample volume (1 to 5 ml). A very high maximum EPS
production was measured in SWP by both the UF and conventional methods (1718 and
1755 mg/l).
2.3 Introduction
During the last decade, exopolysaccharides (EPS) produced by lactic acid bacteria (LAB)
have attracted attention as potential thickening, gelling, stabilizing and emulsifying agents
in fermented dairy products (Cerning et al. 1994). Concentrations of EPS produced by LAB
cultures are generally very low. Production in liquid media is often monitored by viscosity
measurements, which are not necessarily proportional to EPS yields (Cerning et al. 1986;
Sebastiani and Zelger 1998). Very little has been reported on quantification of LAB-
produced EPS and routine quantification methods may be questionable (De Vuyst and
Degeest 1999b). These methods usually involve numerous purification steps such as
polysaccharide-precipitation with ethanol, elimination of contaminating carbohydrates by
dialysis, precipitation of proteins with trichloroacetic acid and freeze-drying prior to total
carbohydrate detection by the phenol-sulfuric acid test (Cerning et al. 1994; Gassem et al.
1997b; Sebastiani and Zelger 1998). These methods are very laborious, time-consuming
and require large sample volumes, which limits the number of samples which can be
analyzed during fermentation.
Nakajima et al. (1990) used ultrafiltration for the recovery of a phosphopolysaccharide
from a slime-forming Lactococcus lactis strain while Toba et al. (1992) first introduced a
method for EPS quantification based on ultrafiltration in a disposable unit. The latter study
did not include a demonstration of complete separation of polysaccharide from interfering
carbohydrates such as lactose and the method was not compared with a conventional
method based on extraction and purification.
The aim of this study was therefore to develop a rapid and accurate method, based on
ultrafiltration in stirred cells, for the determination of EPS produced by Lactobacillus
rhamnosus RW-9595M in culture supernatant and to compare this method with a
conventional method based on EPS extraction and purification (Cerning et al. 1994).
51
2.4 Materials and methods
2.4.1 Microorganism
Lb. rhamnosus RW-9595M, obtained from the Lactic Acid Bacteria Research Network
(RBL Network) culture collection (Dairy Research Centre STELA, Université Laval,
Québec, PQ, Canada) was isolated from reference culture Lb. rhamnosus ATCC 9595 and
shown to produce very high EPS concentrations in defined BMM medium (Dupont et al.
2000). The strain was subcultured aerobically in supplemented whey permeate for 36 h at
37°C. The stock culture was kept frozen in 6% (v/v) rehydrated skim milk and 10% (v/v)
glycerol at -80°C.
2.4.2 Culture media
Basal minimal medium (BMM) was prepared according to Morishita et al. (1981), and
supplemented with lactose (50 g/l). Whey permeate (WP) medium (Foremost, Baraboo,
WI, USA) was reconstituted in distilled water at 5% (w/w), adjusted to pH 5.0 with
1N HCl, autoclaved (121°C, 15 min), cooled to room temperature, filtered on an AP25
prefilter (Millipore Corporation, Bedford, MA, USA) and autoclaved again (121°C,
15 min). Supplemented whey permeate (SWP) medium was prepared as described for WP,
but 0.5 g/l MgSO4 · 7H2O, 0.05 g/l MnSO4 · H2O, 1 ml/l Tween-80 and 1% (w/w)
ultrafiltered (10 kDa) yeast extract (YE) (type: 19512, Organotechnie, La Courneuve,
France) were added after filtration. This YE did not contain high molecular weight
components such as galactomannans which can interfere with EPS quantification. The SWP
medium was sterilised for 15 min at 121°C.
2.4.3 Fermentations
Fermentations were carried out in BMM, WP and SWP media at 37°C and pH 6. The pH-
controlled batch cultures were performed in a 1.5 l bioreactor (Biogénie, Ste-Foy, PQ,
Canada) with BMM and in a 1.5 l bioreactor (Bioflo III, New Brunswick Scientific, Edison,
N.Y., USA) with WP and SWP, respectively. The pH was controlled by addition of
52
6N NH4OH. Inocula were prepared in culture tubes containing 10 ml reconstituted WP
(5% w/w) supplemented with 1% (w/w) YE (Rosell Institute Inc., Montreal, PQ, Canada)
inoculated (10% v/v) with deep frozen stock culture and incubated for 16 h at 37°C. The
resulting culture was then used to inoculate (1% v/v) a second tube with the same medium
and incubated for 10 h at 37°C. This subculturing step was repeated once and the resulting
culture was used to inoculate the bioreactor (2% v/v in BMM and 1.5% v/v in WP and
SWP). Fermentations were carried out for 60 h, 42 h and 26 h in BMM, WP and SWP,
respectively. Samples were taken at different time intervals, depending on base addition
rate for analysis of residual sugar, lactic acid, biomass and EPS concentrations.
2.4.4 Cell enumeration
Viable cell counts (CFU per milliliter) were estimated by plating diluted samples on solid
MRS agar (Difco Laboratories, Richmond, CA, USA). Plates were incubated aerobically at
37°C for 36 h. Reported data are means for duplicate analyses.
2.4.5 EPS purification and quantification by the conventional method
Culture samples were heated to 100°C for 15 min to denature EPS-degrading enzymes.
After cooling, samples were centrifuged (13200 g at 4°C for 25 min) and the supernatants
were stored at -20°C. The conventional method used for EPS extraction and purification
was that of Cerning et al. (1994). Polysaccharides in 50 ml of supernatant were precipitated
by addition of three volumes of chilled absolute ethanol. The mixture was held at 4°C
overnight and centrifuged (13200 g at 4°C for 15 min). The resulting pellet was dissolved
in distilled water, dialysed for 48 h against distilled water (Spectra/Por Membrane, MWCO
3500 Da, Spectrum Laboratories Inc., CA, USA) and freeze-dried. Residual polypeptides
were then removed by precipitation with 10% (v/v) TCA and centrifugation after which the
EPS-containing supernatant was re-dialysed for five days and freeze-dried. The resulting
powder was accurately weighed and stored until total carbohydrate analysis by the phenol-
sulfuric acid test (Dubois et al. 1956).
53
2.4.6 EPS purification and quantification using stirred ultrafiltration
cells
Up to six stirred cells (Omegacell™, Filtron Technology Corporation, Northborough, MA,
USA) with 30 kDa molecular weight cut-off membranes were connected to a reservoir
(RC800 mini-reservoir, Millipore, Bedford, MA, USA) as illustrated in Fig. 2.1. The
reservoir was filled with 0.1 M NaCl solution which was used to reduce hydrophobic
interactions with the membrane. Compressed air regulated at 100 kPa provided the driving
force for filtration. Stopcocks allowed alternating between pressurized air or NaCl solution
to drive either concentration or diafiltration respectively. A 1 to 10 ml accurately measured
volume of supernatant was added per stirred cell. After fitting the stirring bar/pressure cap
assembly onto the cell, filtration was conducted with agitation provided by a multiple
magnetic stirring plate at 650 rpm. Agitation created turbulence and prevented the build-up
of a macromolecular layer at the membrane surface. In order to avoid the formation of a
fouling layer, a high agitation speed and a low pressure (permeation rate) were selected.
The filtration was carried out until no carbohydrate could be detected visually in the filtrate
stream by the colorimetric phenol-sulfuric acid test (Dubois et al. 1956). A sample of final
filtrate stream was taken for subsequent accurate analysis. The carbohydrate concentration
in the final filtrate was always less than 12 mg/l. The retentate was collected, weighed,
stored at -20°C and analysed by the phenol-sulfuric acid test. The retentate EPS
concentration was measured as the carbohydrate concentration minus that of the final
filtrate sample. After use, the cells were filled with 1.0 N NaOH, stirred for 15 min, washed
with distilled water and stored filled with 0.05 N NaOH until the next filtration.
54
Air
Reservoir
Multiple magnetic stir plate
Water(NaCl0.1M)
Stirred cellStopcock
Air
Liquid Stir bar
Manometer
Filtrate
Retentate
Membrane
Fig. 2.1 Schematic diagram of the laboratory device used for ultrafiltration experiments in
stirred cells.
2.4.7 Validation of the ultrafiltration method for EPS analysis
A stock solution of purified EPS was prepared (EPS 1). Fermentation was carried out in
WP, supplemented with 1% (w/w) polysaccharide-free yeast nitrogen base (YNB; Difco
Laboratories, Richmond, CA, USA). After 60 h culture at 32°C with pH controlled at 6.0,
the broth was collected and EPS was purified with the conventional method. The powder
thus obtained was redissolved in distilled water, giving a polysaccharide concentration of
754 mg/l measured by the phenol-sulfuric acid test (Dubois et al. 1956). The stock solution
was diluted 10 and 20-fold in 0.1 M NaCl. A 10 ml volume of these dilutions was
diafiltered in stirred cells, using pressurized 0.1 M NaCl solution, as described above. The
amount of EPS in the retentate was determined by the phenol-sulfuric acid test and
compared with the initial quantity in the sample to calculate product recovery rate (R).
A second EPS stock (EPS 2) was prepared from fermentations carried out in WP
supplemented with YE (SWP), as described before. After 16 h fermentation, a sample of
culture broth was taken and EPS was purified with the conventional method. Diafiltration
experiments as with EPS 1 were repeated with EPS 2 in 0.1 M NaCl in duplicate using 5 ml
of solutions of 68.1 and 180.3 mg/l EPS.
55
To test the effect of culture medium on UF purification, EPS 2 powder was dissolved in 5%
WP solution to a concentration of 1500 mg/l. This EPS stock solution was then diluted with
5% WP to give final EPS concentrations of 0, 50, 100, 400, 1000 and 1500 mg/l. Stirred
cells received 1, 2 or 5 ml of these solutions and ultrafiltration was carried out. The
retentate polysaccharide concentration was then determined by the phenol-sulfuric acid test
and recovery rate was calculated, taking into account the polysaccharide content of the 5%
WP solution without added EPS. Experiments were carried out in triplicate for each
concentration and initial volume in the stirred cells.
Finally, the new method was validated with samples from pH-controlled batch
fermentations with Lb. rhamnosus RW-9595M carried out in BMM, WP and SWP media
and data were compared with that obtained with the conventional method.
2.4.8 Sugar and lactic acid analysis
Total carbohydrate concentration was determined by the phenol-sulfuric acid test (Dubois
et al. 1956). The EPS-content was calculated in glucose equivalents from glucose standard
curves. Reported data are means for triplicate analyses.
Samples of culture broth were centrifuged (13200 g at 4°C for 25 min) and residual sugar
and lactic acid concentrations in the supernatant were determined by HPLC (Waters,
Millipore Co. Montreal, QC, Canada) using a Phenomenex ion column (Phenomenex,
Torrance, CA) and H2SO4 0.0064N as eluent at a flow rate of 0.4 ml/min. Analysis was
performed in duplicate.
2.4.9 Statistics
ANOVA, Tukey-Kramer HSD multiple mean comparison and linear regressions were
carried out using the software JMP IN (SAS Institute Inc., version 3.2.6, Cary, NC) with a
level of significance at 0.05. EPS data was transformed (arcsin(sqrt(X/10000)) to stabilize
the variance and normalize the residuals.
56
2.5 Results
2.5.1 Characterization of the UF method
First, ultrafiltration and quantification of EPS was carried out with aqueous solutions of
known concentration (Tab. 2.1). For EPS 1 samples containing 37.7 and 75.4 mg/l EPS,
high mean recovery rates of 85.7 and 86.7%, respectively, were measured. The method was
highly repeatable as indicated by the low standard deviation of 0.4% and 0.7% calculated
for 2 repetitions. For EPS 2 solutions containing 68.1, 205.7 and 1095.8 mg/l, similar
results were obtained, with mean recovery rates between 83.1 and 87.6% with standard
deviations lower than 1% calculated for 2 repetitions. There was no significant difference in
recovery rate from EPS solutions of differing concentrations nor for different EPS powders.
Subsequently, the effects of sample volume and EPS concentration on the UF method were
also examined using solutions of purified EPS 2 powder prepared in 5% WP. Analysis of
variance showed that there was no statistically significant effect (P = 0.198) of initial
sample volume in the stirred cell on measured EPS concentration. The polysaccharide
concentration in the 5% WP solution without added EPS was 14.4 mg/l (±3.7). This amount
was subtracted from polysaccharide concentrations measured in EPS samples to obtain the
EPS recovery rates shown in Tab. 2.1. A linear relationship (R2 = 0.98; p<0.001) existed
between the measured (EPSm) and the initial (EPSi) EPS concentrations:
Eq. 1:
EPSm = 9.60 + 1.04 · EPSi
High EPS recovery rates (96 to 105%) and low standard deviations (4 to 36 mg/l) for EPS
concentration were observed. The absence of sugars in the filtrates suggested complete
elution of lactose, although some retention of low molecular weight sugars due to
membrane fouling could also occur. Thus, three retentate samples were ultrafiltered in new,
never used stirred cells and filtration was carried out in the concentration mode with air
pressure. No carbohydrates were detected by the phenol-sulfuric acid test in the resulting
filtrates (data not shown).
57
Tab. 2.1 EPS concentration and recovery rate (R) determined by the UF method for 0.1 M
NaCl and 5% WP solutions spiked with EPS.
EPS
concentration (mg/l) Solution
initial measured
R
(%)
37.7 32.3 ± 0.4 85.7 ± 1.1 EPS 1 75.4 65.4 ± 0.7 86.7 ± 0.9
68.1 56.6 ± 0.7 83.1 ± 1.0
205.7 180.3 ± 0.001 87.6 ± 0.0005
0.1 M
NaCl EPS 2
1095.8 912.2 ± 7.7 83.2 ± 0.7
0 14.4 ± 3.7 ---
50 62.4 ± 7.5 95.9 ± 22.4
100 98.2 ± 13.8 83.8 ± 17.6
400 423.4 ± 31.0 102.2 ± 8.7
1000 1038.5 ± 45.8 102.4 ± 4.9
5%
WP EPS 2
1500 1586.7 ± 35.8 104.8 ± 2.6
2.5.2 EPS quantification during batch cultures
To examine the possible influence of the culture medium on EPS determination, batch
fermentations were carried out in BMM, WP and SWP media with Lb. rhamnosus RW-
9595M at 37°C and pH controlled at 6.0. The mean profile for three fermentations in BMM
is shown in Fig. 2.2. The viable cell concentration increased exponentially with no apparent
lag growth phase for nearly 16 h culture and peaked at 6.9 ± 1.8 · 109 CFU/ml at 32 h,
remaining stable until the end of the 60 h culture. All lactose was consumed by this time
and about 41 g/l lactic acid was produced. The two methods used for estimating EPS
concentration gave significantly different values, the UF method resulting in higher values
than the conventional method. A high maximum EPS production of 1053 ± 98 mg/l and
530 ± 173 mg/l was measured in BMM after 56 and 48 h culture by the UF and
conventional method, respectively. Determination of EPS by the UF method was done in
58
triplicate but the high sample volume of 50 ml required for the conventional method
precluded such repetition.
Fig. 2.2 Change in viable cell count ( ), lactose ( ) and lactic acid ( ) concentrations,
and EPS production measured by the UF ( ) and conventional ( ) methods during pH-
controlled batch cultures with Lb. rhamnosus RW-9595M in BMM. Means and standard
deviations for three fermentations.
A batch fermentation with pH controlled at 6 was carried out in WP medium (Fig. 2.3).
After approximately 24 h, the viable cell concentration reached a maximum of
1.9x108 CFU/ml. The polysaccharide concentration, determined by the UF method,
continuously increased from 13.09 ± 1.22 mg/l in the freshly inoculated medium to a
maximum of 44.0 ± 0.9 mg/l after 42 h culture. The conventional method indicated 8 mg/l
at time zero and a maximum polysaccharide concentration of 22.3 mg/l after 42 h.
59
Fig. 2.3 Change in viable cell count ( ), volume of base consumed (―), and EPS
production measured by the UF ( ) and conventional ( ) methods during a pH-controlled
batch culture with Lb. rhamnosus RW-9595M in WP. Means and standard deviations for
duplicate analyses by the UF method.
Data obtained for three fermentations in SWP are presented in Fig. 2.4. Viable cell
concentrations were very high (1.1 ± 0.1 · 1010 CFU/ml) after approximately 16 h culture
with no lag growth phase. All lactose was consumed after 16 h and approximately 36 g/l
lactic acid was produced. Very high and similar EPS productions were measured by both
the UF and conventional methods. The conventional method indicated a significant level of
polysaccharide (332 ± 75 mg/l) in the freshly inoculated fermentation medium at time zero
and a maximum concentration of 2087 ± 287 mg/l after 26 h culture, for a calculated EPS
production of 1755 mg/l. The UF method gave an initial polysaccharide concentration of
430 ± 35 mg/l and a maximum concentration of 2148 ± 134 mg/l after 16 h culture, for a
calculated EPS production of 1718 mg/l.
60
Fig. 2.4 Change in viable cell count ( ), lactose ( ) and lactic acid ( ) concentrations,
and EPS production measured by the UF ( ) and conventional ( ) methods during pH-
controlled batch cultures with Lb. rhamnosus RW-9595M in SWP. Means and standard
deviations for three fermentations.
2.6 Discussion
In this study, a new method for the quantification of EPS produced by Lb. rhamnosus RW-
9595M, using ultrafiltration and diafiltration in stirred cells with a 30 kDa MWCO
membrane is described. To investigate the suitability of this system, filtration experiments
with aqueous solutions of known EPS concentrations prepared with purified EPS from two
different fermentations (EPS 1 and EPS 2) were conducted. A high EPS fraction of 83.1%
to 87.6% was retained by the membrane and measured in the retentate (Tab. 2.1). The high
EPS recoveries and reproducibility of the method suggest that quantitative separation of
EPS from interfering low molecular weight carbohydrates may be achieved.
To simulate the use of a complex growth medium containing a high amount of simple
sugars, filtrations were conducted with EPS solutions in 5% WP, containing approximately
61
40 g/l lactose and EPS concentrations between 0 and 1500 mg/l. For each concentration,
three different volumes (1, 2 and 5 ml) were used in the stirred cells, filtration was carried
out in triplicate and EPS concentrations were determined (Tab. 2.1). The measured EPS
concentration was not influenced by the initial sample volume in the stirred cells
(P = 0.198) but highly correlated with the initial EPS concentration (P < 0.0001; Eq. 1).
The high EPS recoveries from WP solutions between 96 and 105% show that under the
conditions used, low molecular weight (MW) carbohydrates (lactose) are eliminated
through the membrane and do not interfere with the determination of EPS concentration in
the retentate, using the phenol-sulfuric acid test. Thus, low MW carbohydrates should be
found in the filtrate. Unfortunately, a complete material balance is not possible because the
error of the carbohydrate quantification in the filtrate is in the range of the actual
concentration in the retentate. The possibility of membrane fouling during filtration, which
could lead to retention of low MW sugars, was tested by processing retentates obtained at
the end of filtration in a new ultrafiltration cell. The absence of carbohydrates in the filtrate
indicated that the retentate at the end of the first filtration did not contain detectable low
MW sugars. Data from this study demonstrate that the UF method quantitatively separated
EPS produced by Lb. rhamnosus RW-9595M from interfering low MW carbohydrates in a
complex fermentation broth and yielded accurate measurements of EPS concentration.
Toba et al. (1992) used a disposable ultrafiltration unit with a MWCO of 5000 Da and
reported recovery rates close to 100% for polysaccharide standards, such as pullulan and
dextran. However, these data were obtained with polysaccharide standards having little
variation in their molecular weights. In contrast, EPS produced by LAB have different
structures and molecular weights (De Vuyst and Degeest 1999b). In addition, EPS with the
same structure but very different size are produced during fermentation (Degeest and de
Vuyst 1999; Grobben et al. 1997). In this study, EPS purification by the conventional
method to produce EPS powders was done using dialysis membranes of 3500 Da.
Carbohydrates in the 3500 Da to 30 kDa range which were retained during this purification
could have crossed the 30 kDa UF membrane, thereby decreasing EPS recovery rates in the
retentate. This could explain some observed data with recovery rates lower than 100%.
62
The UF method was then directly compared with the conventional method of Cerning et al.
(1994) in measuring EPS production during pH-controlled batch cultures with
Lb. rhamnosus RW-9595M. To examine possible effects of the fermentation medium
composition, cultures were carried out in BMM, WP and SWP media. The basal minimum
medium was chosen for the absence of interfering polysaccharides and because it gave high
biomass and EPS productions during pH-controlled batch fermentations with this strain
(Dupont et al. 2000). A maximum EPS concentration of 1053 mg/l was measured by the
UF method after 56 h of culture in BMM compared to only 530 mg/l by the conventional
method after 48 h (Fig. 2.2). This difference may be partly explained by losses of EPS
during the numerous purification steps of the conventional method, due to sticking of the
EPS to the dialysis membrane and incomplete precipitation in ethanol (Kimmel et al.
1998). However, the time change in EPS concentration indicated by both methods was
similar, reaching 88 and 72% of the maximum EPS concentration after 32 h of culture,
which corresponded to the end of cell growth.
Fermentations in WP media yielded very low maximum EPS concentrations of 30.1 and
14.3 mg/l, measured by the UF and conventional methods, respectively. Repetitions of EPS
analysis by the UF method had a very low standard deviation in this low concentration
range. Freshly inoculated WP medium contained only a small amount of polysaccharide
(13.9 and 8 mg/l by the UF and conventional methods, respectively), partly due to EPS
transferred with the inoculum. The low EPS production maybe explained by the limited cell
growth in this medium.
Supplementation of WP with minerals, Tween-80 and YE increased both biomass and EPS
production (Fig. 2.4) by Lb. rhamnosus RW-9595M with biomass rapidly reaching a very
high maximum of 1.1 ± 0.1 · 1010 CFU/ml. Lactose as carbon source at an initial
concentration of 40 g/l was completely consumed after 16 h of culture, when maximum
viable biomass was measured. Both the UF and conventional methods indicated large
amounts of polysaccharide in the freshly inoculated fermentation medium (430 ± 35 and
332 ± 75 mg/l, respectively). Since freshly inoculated WP medium contained only traces of
EPS, polysaccharide levels in inoculated SWP medium may be due to YE supplementation.
In this study, ultrafiltered YE containing no components larger than 10 kDa was used. Any
63
polysaccharides contributed by this YE should therefore cross the 30 kDa MWCO UF
membrane. The large amount of polysaccharide found in the inoculated SWP medium
could be due to reactions between YE components and sugars during medium sterilization.
Torino et al. (2000) reported this type of interaction as well as the formation of nitrogen-
sugar complexes which may precipitate with ethanol but are not completely removed by
TCA precipitation by the conventional method. These complexes may have a high
molecular weight since they are retained by the 30 kDa UF membrane.
The kinetics of EPS production in SWP are very similar whether measured by the
conventional or the UF method (Fig. 2.4). The maximum polysaccharide concentration was
2148 ± 134 mg/l by the UF method after 16 h culture and 2087 ± 287 mg/l by the
conventional method after 26 h. By subtracting the polysaccharide content in the freshly
inoculated medium, a maximum EPS production of 1718 and 1755 mg/l was determined by
the UF and conventional methods, respectively. This is the highest EPS production reported
in the literature for lactobacilli.
Under the experimental conditions tested, EPS production in SWP was coupled with
growth. The EPS concentration measured by both methods did not change significantly
(P > 0.05) after 16 h of culture which could indicate the absence of glycohydrolase activity.
Degradation of EPS has been observed during prolonged incubation (Gassem et al. 1997a;
Mozzi et al. 1996a) and attributed to glycohydrolase activity (Pham et al. 2000). The
difference in EPS concentrations (355 mg/l) indicated by the two methods after 16 h of
incubation in SWP, corresponding to the end of the growth phase, is similar to this
difference for maximal EPS concentration in the BMM medium (523 mg/l). Although this
difference was not statistically significant in SWP (P = 0.25), it may indicate a constant and
considerable EPS loss during the various steps of the conventional method.
Stirred cells were used for ten analyses and then discarded. However, there was no
difference in the flux measured with water for new cells or for cells after ten uses.
Membrane pores were therefore not blocked after ten filtrations under the operating and
cleaning conditions used and stirred cells could probably be used for more than ten analyses
without significant changes in membrane permeability.
64
2.7 Conclusions
Data from this study show that the new method based on UF separation of EPS from simple
sugars in culture broth allows accurate monitoring of EPS production by LAB during
fermentations. Compared with the conventional method, quantification by the UF method is
much less time-consuming (8 h compared to about 10 days). Furthermore, this method is
simple and requires only small sample volumes, as low as 1 to 5 ml, which allows for more
analyses and test repetitions to be performed during fermentations.
Chapitre 3
Exopolysaccharide production during batch cultures
with free and immobilized Lactobacillus rhamnosus
RW-9595M
Dirk Bergmaier1, Claude P. Champagne2 and Christophe Lacroix3
1 STELA Dairy Research Centre, Pavillon Paul Comtois, Université Laval, Québec, PQ,
Canada, G1K 7P4
2 Food Research and Development Center, Agriculture and AgriFood Canada, St-
Hyacinthe, PQ, Canada, J2S 8E3
3 Laboratory of Food Biotechnology, Institute of Food Science and Nutrition, Swiss Federal
Institute of Technology, ETH Zentrum, LFO F18, CH-8092 Zurich, Switzerland
66
3.1 Résumé
La production d'exopolysaccharide (EPS) par Lactobacillus rhamnosus RW-9595M a été
étudiée lors des cultures en batch à pH contrôlé avec des cellules libres et lors des cultures
en batch répété avec des cellules immobilisées par adsorption sur des supports poreux
solides (ImmobaSil®). Les cultures ont été conduites à pH 6 dans un milieu de perméat de
lactosérum supplémenté (SWP), contenant du perméat de lactosérum à une concentration
de 5% ou de 8% (w/w). Pour des cultures en batch avec les cellules libres dans le milieu de
8% SWP, des comptes cellulaires (1.3 · 1010 CFU/ml) et une production d'EPS (2350 mg/l)
très élevées ont été mesurées après respectivement 18 et 32 h de culture. Plusieurs
méthodes pour la détermination de la biomasse immobilisée sur des supports solides basées
sur l'analyse des composants de biomasse (protéines, ATP et ADN) ont été examinées. La
méthode d'analyse d'ADN s'est avérée la plus appropriée dans ces circonstances. Cette
méthode a dosé une haute biomasse immobilisée de 8.5 · 1011 CFU/ml après la colonisation
des supports ImmobaSil®. Pendant les cultures en batch répété avec des cellules
immobilisées, une concentration élevée d'EPS (1808 mg/l) a été mesurée après quatre
cycles pour une courte période d'incubation de 7 h dans 5 % de SWP. La biomasse élevée
dans le système de cellules immobilisées a augmenté la productivité volumétrique
maximale d'EPS (258 mg/l·h après 7 h) comparée aux cultures en batch avec des cellules
libres (110 mg/l·h après 18 h). Notre étude montre clairement le potentiel élevé de la
souche et de la technologie des cellules immobilisées pour la production d'EPS comme
ingrédient fonctionnel alimentaire.
3.2 Abstract
The production of exocellular polysaccharides (EPS) by Lactobacillus rhamnosus
RW-9595M was investigated during pH-controlled batch cultures with free cells and
repeated-batch cultures with cells immobilized by adsorption on solid porous supports
(ImmobaSil®). Cultures were conducted at pH 6 in supplemented whey permeate (SWP)
medium containing 5% or 8% (w/w) whey permeate. For free-cell batch cultures in 8%
SWP medium, very high maximum cell counts (1.3 · 1010 CFU/ml) and EPS production
(2350 mg/l) were measured after 18 and 32 h, respectively. Several methods for the
67
determination of immobilized biomass on solid supports based on analysis of biomass
components (proteins, ATP and DNA) were tested. The DNA analysis method proved to be
the most appropriate under these circumstances. This method revealed a high immobilized
biomass of 8.5 · 1011 CFU/ml support after colonization of the ImmobaSil® supports.
During repeated immobilized cell cultures, a high EPS concentration (1808 mg/l) was
measured after four cycles for a short incubation period of 7 h in 5 % SWP. The high
biomass in the immobilized cell system increased maximum EPS volumetric productivity
(258 mg/l·h after 7 h culture) compared with free cell batch cultures (110 mg/l·h after 18 h
culture). Our study clearly shows the high potential of the strain and immobilized cell
technology for production of EPS as a functional food ingredient.
3.3 Introduction
Polysaccharides are widely used in the food industry as thickeners, viscosifiers, stabilizing
or emulsifying agents, gelling agents or texturizers (Sutherland 1998). The majority of
these additives are of plant origin, such as starch, locust bean gum and alginate. Until now,
xanthan, curdlan and gellan have been the only FDA approved microbial polysaccharides
although they are produced by non-GRAS (Generally Recognized As Safe) bacteria. Many
food-grade microorganisms, such as lactic acid bacteria (LAB), also produce exocellular
polysaccharides (EPS) (Cerning 1990; De Vuyst and Degeest 1999b). In situ-produced EPS
play an important role in the manufacture of fermented dairy products such as yogurt,
drinking yogurt, cheese, fermented cream and milk-based desserts (Duboc and Mollet
2001). They contribute to the texture, mouthfeel, taste perception and stability of the final
products. EPS act as texturizers and stabilizers and so decrease syneresis and improve
product stability. Furthermore, some EPS classified as prebiotics could contribute to human
health and positively affect gut microflora (Ruas-Madiedo et al. 2002a).
In spite of these interesting properties, EPS from LAB are not yet exploited by food
manufacturers as food additives (De Vuyst and Degeest 1999a). Their use could result in
safe, natural end-products with improved rheological properties and enhanced stability,
especially for the dairy industry. However, compared with dextran-producing Leuconostoc
or Gram-negative EPS producers, the low production of EPS by LAB is a constraint for
68
their commercial use as food additives. In this respect, fermentation technologies that can
be used in the industry need to be developed in order to enhance EPS production and
develop new EPS bioingredients.
It has been shown that immobilized cell technology (ICT) with LAB could increase the
biomass concentration maintained in the fermentation system (Champagne et al. 1994;
Norton et al. 1994a). Coupled with repeated-batch or continuous culture, ICT could largely
increase process productivity and cell stability (Bertrand et al. 2001; Lamboley et al. 1997).
Cell immobilization also protects cells against shear damage. Furthermore, reuse of cells
and more constant product characteristics could facilitate downstream processing of EPS.
Immobilization by adsorption on porous preformed and inert supports could be an
immobilization technique suited for EPS-producing cultures. The production of capsular
and free EPS by the cells may promote their adsorption to the support and subsequent
colonization (Dunne 2002). However, it is difficult to accurately determine the
concentration of immobilized cells in solid supports, an important parameter of the
fermentation process (Wang 1988). Disruption of the immobilization matrix and viable cell
enumeration, commonly used with gel beads, will result in very high shear stress and
mortality of cells, whereas biomass dry weight determinations will quantify not only
biomass but also substances accumulated in the support matrix, such as EPS.
In this study, different methods for quantification of immobilized biomass, based on the
extraction and analysis of specific components or molecules of the biomass such as
proteins, adenosine triphosphate (ATP) and deoxyribonucleic acid (DNA), were compared.
Bacterial growth and EPS production during batch and repeated-batch cultures with free
and immobilized cells of Lb. rhamnosus RW-9595M, a strain that has shown very high
EPS production in a whey permeate-based medium (Bergmaier et al. 2001; Macedo et al.
2002b) was studied. The mucoid properties of Lb. rhamnosus RW-9595M were used to
promote adsorption on solid porous supports (ImmobaSil®) for cell immobilization.
69
3.4 Materials and Methods
3.4.1 Strain and culture media
Lb. rhamnosus RW-9595M, obtained from the Lactic Acid Bacteria Research Network
(RBL Network) culture collection (Dairy Research Centre STELA, Université Laval,
Québec, PQ, Canada), was isolated from reference culture Lb. rhamnosus ATCC 9595 and
shown to produce very high EPS concentrations in the defined BMM medium (Dupont et
al. 2000) and in supplemented whey permeate medium (Bergmaier et al. 2001; Macedo et
al. 2002b). The strain was subcultured aerobically in supplemented whey permeate for 36 h
at 37°C. The stock culture was kept frozen in 6% (v/v) rehydrated skim milk and 10% (v/v)
glycerol at -80°C. For inoculum preparation, a fresh culture was propagated twice in 5%
whey permeate with 1% yeast extract at 37°C for 10 h or until pH 4.8 was reached.
The supplemented whey permeate (SWP) medium was prepared as follows. Whey
permeate powder (Foremost, Baraboo, WI, USA) was rehydrated to give a final
concentration of 5% or 8% (w/w) and the pH was adjusted to pH 5.0 with 1 N HCl. The
solution was autoclaved (121°C, 15 min), cooled to room temperature and filtered on a
AP25 prefilter (Millipore Corporation, Bedford, MA, USA). The other components
MgSO4 · 7H2O, MnSO4 · H2O and Tween-80, were added to give final concentrations of
0.5 g/l, 0.05 g/l and 1 ml/l, respectively, and the solution was autoclaved again. A yeast
extract (YE) solution was prepared by adding 40 g of YE (Rosell Institute Inc., Montreal,
PQ, Canada) to 100 ml deionized water. This YE concentrated solution was autoclaved
(121°C, 15 min) and added to the whey permeate medium to give a final YE concentration
of 1%.
3.4.2 Fermentation techniques
Fermentations were carried out in a 1.5 l bioreactor (Bioflo III, New Brunswick Scientific,
Edison, NY, USA) with a total working volume of 1.2 l. Temperature was controlled at
37°C and pH at 6 by addition of 6 N NH4OH. Free-cell batch cultures were performed in 5
or 8% SWP medium with 1.5% (v/v) inoculum size. Samples of culture broth were taken
70
for analysis at different time intervals, depending on the base addition rate. Cells for DNA
analysis were sampled during exponential growth phase as estimated by the observed base
addition rate.
For repeated batch cultures with immobilized cells in 5% SWP medium, the bioreactor was
filled with 150 ml ImmobaSil® supports (Ashby Scientific Ltd., Coalville, Leicestershire,
UK). After support conditioning according to the manufacturer's instructions, the bioreactor
was filled aseptically with 500 ml SWP and inoculated at 4% (v/v). A stirring regime of
5 min at 50 rpm followed by 30 min with no stirring was applied for 4 h. After this time,
the first fermentation was started with stirring set at 100 rpm and pH controlled at 6. After
8 h, fresh medium was added to the bioreactor for a total volume of 1.2 l. The fermentation
medium was totally replaced when a volume of 80 ml 6 N NH4OH was used for pH
control, which corresponded to late exponential growth phase of the culture. A total of four
repeated batch cultures were performed.
3.4.3 Cell enumeration and biomass determination
Viable cell counts (CFU per milliliter) were estimated by plating diluted samples on solid
MRS agar (Difco Laboratories, Richmond, CA, USA). Plates were incubated aerobically at
37°C for 36 h. Reported data are means for triplicate analyses. For determination of the cell
dry weight in the broth, 10 ml of broth were centrifuged at 10,000 g for 15 min at 4°C
(Sorval Instrument, Dupont, Newtown, CO, USA). The cell pellet was washed twice with
distilled water and then transferred to a preweighed aluminium dish. The cells were dried to
a constant weight in a vacuum oven at 70°C. Reported data are means for duplicate
analyses.
3.4.4 Immobilized biomass determinations
3.4.4.1 DNA extraction
The immobilized cell concentration was determined by measuring the DNA content using
the method described by Wang (1988) with some modifications. For calibration, the DNA
content of cells was correlated with viable cell counts and biomass dry weight using
71
effluent samples from free-cell pH-controlled batch cultures with cells in the exponential
growth phase. As a consequence of the high EPS production by Lb. rhamnosus
RW-9595M, it was impossible to accurately determine the cell dry weight (fluffy pellet and
obstruction of filters). Therefore, the strain Lb. rhamnosus ATCC 9595 was used for this
part of the study. This strain is the parent strain from which the variant strain
Lb. rhamnosus RW-9595M was isolated and it produces only a very small amount of EPS
(Dupont et al. 2000).
For DNA extraction, the fermented medium was centrifuged (10,000 g at 4°C for 15 min).
The pellet was resuspended in 10 ml of a saline-citric solution (SCS) containing 8.77 g/l
NaCl and 1.47 g/l Na3C6H5O7 · 2H2O at pH 7 and centrifuged again. The pellet was
resuspended in 2 ml of SCS solution with 0.25 N perchloric acid (pH 1.45) and incubated
for 30 min at 0°C. After centrifugation (10,000 g at 0°C for 10 min), 4 ml 0.5 N perchloric
acid solution was added to the pellet, the tube was sealed and incubated in a water bath at
70°C for 30 min. The tubes were cooled to room temperature for exactly 25 min and
centrifuged (5,000 g, 10 min, 20°C). The supernatant was kept at 4°C for a maximum of
1 day until analysis. The DNA concentration was determined by the diphenylamine method
(Burton 1956). The supernatant was diluted with 0.5 N perchloric acid to be in the standard
curve concentration range. Two ml of diphenylamine reagent, prepared the same day with
1.5 g diphenylamine in 100 ml demineralized water, 1.5 ml concentrated H2SO4 and 0.5 ml
1.6% acetaldehyde, were added to a 1-ml diluted sample. A standard curve of deoxyribose
in a concentration range from 0 to 50 µg/ml was prepared. Standards and samples were
incubated at 30°C for 17 h. Absorbance was measured spectroscopically at 595 nm with
background correction at 650 nm. Linear correlations between DNA content, cell dry
weight and cell counts were determined.
To determine the DNA concentration in the solid supports, a sample of about 3 to 4
supports was taken and the wet weight was determined. The supports were washed twice
with SCS solution and dried on a filter paper. The supports were transferred into glass tubes
with 3 ml SCS and 2.5 N perchloric acid was added to give a final concentration of 0.25 N
(pH 1.45). After incubation at 0°C for 30 min, the excess liquid was removed on a filter
paper. For DNA extraction the supports were transferred to a 10 ml centrifugation tube and
72
3 ml 0.5 N perchloric acid were added. The samples were incubated in a water bath at 70°C
for 25 min and cooled to room temperature for 25 min. The DNA content of the clear
supernatant was analyzed by the diphenylamine method, as described above.
As only wet weight of colonized supports was determined during the DNA extraction
method, a correlation between support wet and dry weights and support volume was
established. The wet weight of SCS washed colonized supports was determined in the same
way as during DNA extraction. Support volume was measured by water displacement in a
graduated cylinder and the supports were dried in a vacuum oven at 70°C until constant
weight was obtained.
The immobilized cell concentration was calculated with the correlation between DNA
content, viable cell counts and biomass, assuming that the DNA content per cell of
immobilized Lb. rhamnosus RW-9595M and free cells of Lb. rhamnosus ATCC-9595 is
the same per cell. Immobilized cell concentration was expressed as colony-forming units or
cell dry weight per support dry weight (CFU/g or g/g, respectively). Each analysis was
repeated three times.
3.4.4.2 ATP extraction
The quantity of ATP in a sample containing planktonic cells was determined using the
firefly bioluminescence method as described by Gikas and Livingston (1993). For ATP
extraction from cells, one ml of sample was mixed with 9 ml of a Tris-EDTA buffer and
incubated at 100°C for 3 min. Then the extracted ATP reacted with luciferin (LH2) in a
reaction catalyzed by the luciferase enzyme and produced luminescence that was measured
using a Wallac Victor-1420 microplate reader. The ATP Bioluminescence Assay Kit CLS
II (Boehringer Mannheim GmbH, Germany) was used according to the manufacturers
standard protocol.
3.4.4.3 Protein extraction
Broth samples (25 ml) were centrifuged (7500 g at 4°C for 15 min) and the pellet was
washed three times with 0.95% NaCl solution. For protein extraction, 10 ml 0.1 M NaOH
were added to the pellet and the sample was heated at 100°C for 30 min. After
73
centrifugation (7500 g at 4°C for 15 min) the protein concentration in the supernatant was
determined using the DC Protein Assay (Bio-Rad Laboratories, Hercules, CA, USA) with
bovine serum albumin as standard. For determination of protein content of immobilized
cells, 1 g of support was treated as described for cell pellets except that cells were
ultrasonicated (Aquasonic Model 250T, VWR Scientific, West Chester, PA) for 2 h in
0.1 M NaOH before the heating step.
3.4.5 EPS concentration analysis
Homogeneous culture broth samples were heated to 100°C for 15 min, cooled and
centrifuged (13,200 g at 4°C for 25 min). Supernatants were stored at -20°C.
Polysaccharides in supernatant were partially purified by a new ultrafiltration method
(Bergmaier et al. 2001) (Chapitre 2), and total carbohydrate was quantified by the phenol-
sulfuric acid method (Dubois et al. 1956) with glucose as standard. The concentration of
EPS produced during fermentation was calculated by subtracting the polysaccharide
concentration in the fresh medium from that measured in the fermented broth.
3.4.6 Sugar and organic acid analysis
Culture broth samples were centrifuged (13,200 g at 4°C for 25 min), diluted and filtered
on an Acrodisc LC13 filter (0.2 µm; Gelman Sciences, Ann Arbor, MI, USA). Residual
sugars and lactic acid concentration in the supernatant were determined by HPLC (Waters,
Millipore Co. Montreal, QC, Canada) using a Phenomenex ion column (Phenomenex,
Torrance, CA) and H2SO4 0.0064N as eluent at a flow rate of 0.4 ml/min. Analysis was
performed in duplicate.
3.5 Results and Discussion
In this study, pH-controlled batch cultures in a whey permeate based medium with
Lb. rhamnosus RW-9595M were carried out. Bacterial growth and EPS production during
free-cell batch cultures were compared with repeated-batch cultures with cells immobilized
on solid porous supports.
74
3.5.1 Cell and EPS production during free-cell batch cultures
Data obtained for two free-cell batch fermentations in 8% SWP medium are presented in
Fig. 3.1. The free-cell counts increased rapidly during the pH-controlled culture and
reached a very high maximum value of 1.31 ± 0.05·1010 CFU/ml after 18 h. This data
shows the suitability of the whey-permeate-based medium for biomass growth. Lactose as
the only carbon source in this medium with an initial concentration of 64.9 ± 0.3 g/l was
completely consumed after 32 h culture. Lactic acid was the only organic acid produced,
for a final concentration in the fermented broth of 58.7 ± 0.8 g/l. When the maximum
population was reached (18 h), only 43 g/l of lactic acid had been produced (Fig. 3.1).
Uncoupling between growth and lactic acid production was thus observed after 18 h of
fermentation, and approximately 25% of acid production occurred during this phase. Such
uncoupling between growth and acidification has been reported with lactobacilli (Oyaas et
al. 1996). Although EPS production kinetics were similar to that of lactic acid production,
it is noteworthy that little EPS production was observed after 18 h of fermentation.
Therefore, in free-cell fermentations, EPS production appeared more closely linked to
growth than was acidification. After 32 h culture, a high total polysaccharide concentration
in the fermented broth of 2728 ± 38 mg/l was measured. The final EPS production
calculated by subtracting the initial polysaccharide content in the medium (378 ± 13 mg/l),
which is mainly due to YE supplementation (Bergmaier et al. 2001; Torino et al. 2000),
was 2350 ± 51 mg/l. The EPS volumetric and specific productivities were maximum after
18 h, equal to 110.3 mg/l·h and 8.45·10-12 mg/CFU·h, respectively.
75
Fig. 3.1 Viable cell counts (●), lactose (■) and lactic acid (♦) concentrations, and EPS
production (▲) during pH-controlled batch cultures with Lb. rhamnosus RW-9595M.
Means and standard deviations for two fermentations.
The EPS production obtained in this study, more than 2.3 g/l, is one of the highest reported
for lactobacilli in the literature. Only Macedo et al. (2002b) reported higher values
(2775 mg/l) for the same strain in a complex and rich medium composed of whey permeate
supplemented with yeast extract and vitamins, salts and amino acids of the defined BMM
medium (Morishita et al. 1981). However, the EPS production by Lb. rhamnosus
RW-9595M is still much lower than the high yields obtained with dextran-producing LAB
and Gram-negative EPS producers such as X. campestris with very high productions of 10-
25 g/l (Becker et al. 1998). De Vuyst and Degeest (1999b) stated that, from an economic
point of view, a production of 10-15 g/l would be required in order to use EPS from LAB
as functional (thickener, gelling agent) food additives.
76
3.5.2 Cell production during repeated batch cultures with immobilized
cells.
In order to increase biomass in the fermentation system, and thus achieve higher
productivity, Lb. rhamnosus RW-9595M cells were immobilized on ImmobaSil® solid
porous supports which were used during repeated pH-controlled cultures. Data obtained for
four consecutive batch cultures with immobilized cells in 5% SWP medium are presented
in Fig. 3.2. Each culture was carried out until about 80 ml of 6 N base was used to control
pH at 6. This base volume corresponds to a theoretical lactic acid production of about
41 g/l, and to nearly complete conversion of lactose in the medium (43 g/l) into lactic acid
(Bergmaier et al. 2001) (Chapitre 2). This was verified by HPLC analysis of samples taken
at the end of the four consecutive batch cultures. In these samples, residual lactose
concentration ranged between 0 and 5 g/l and a high concentration of lactic acid between
33 and 38 g/l was tested.
With this repeated-cycle batch fermentation strategy, a decrease of fermentation time was
observed with an increase in the cycle number, with 16, 9, 7, and 7 h from the first to the
fourth batch culture. The enumeration of free-cells in the fermentation broth showed very
high cell concentrations at the end of incubation before medium change, with a mean of
1.02 ± 0.14·1010 CFU/ml (Fig. 3.2). This cell concentration is equal (p<0.05) to that
obtained during batch cultures in 8% SWP medium in this study
(1.31 ± 0.05 · 1010 CFU/ml) and to that measured during batch fermentations in 5% SWP
(1.1 ± 0.1 · 1010 CFU/ml) (Bergmaier et al. 2001) (Chapitre 2). Between two consecutive
cultures the medium was completely changed and the new medium was mixed with the
supports. The mean free-cell count in the broth after this change was high
(3.9 ± 0.5 · 108 CFU/ml) probably due to incomplete broth removal in the void spaces of
the support and cell release from the support. The rapid build up of free cells during
incubation resulted from both free cell growth and immobilized cell growth associated with
cell release from the solid supports (Lamboley et al. 1997).
77
Fig. 3.2 Free-cell counts (●), immobilized cell concentration measured by DNA extraction
method (■) and polysaccharide concentration in the broth (vertical bars) during four
repeated batch cultures with Lb. rhamnosus RW-9595M immobilized on ImmobaSil®
silicone rubber solid supports.
3.5.3 Immobilized cell concentration in the solid supports
The knowledge of the content of immobilized biomass in solid supports is important for
process analysis and optimization. However, conventional methods such as dry weight or
viable cell enumeration are not suitable for cells immobilized in solid supports, particularly
for EPS-producing strains. Biomass dry weight determination is greatly influenced by
products accumulated in the porous support and viable cell count determination requires an
initial step to release immobilized cells with no loss of viability before cell enumeration,
which is not possible with solid supports. Therefore, several methods for immobilized
biomass estimation were tested in this study. Specific cell components, proteins, ATP and
DNA, were quantified during free-cell cultures and calibration curves were developed to
relate the component concentration with viable cell counts or biomass concentration. These
78
calibrations could then be used to estimate the immobilized biomass or cell concentration
from the specific component concentration tested in the solid support.
One major constituent of microbial cells are proteins. About 57% of the dry weight of a
typical bacterium is protein (Atkinson and Mavituna 1991). In the present study, the
amount of proteins in planktonic cells was determined and correlated with biomass. An
amount of 252.4 mg proteins per g dry weight of bacteria was determined (results not
shown). However, protein extraction experiments with colonized carriers resulted in an
important variance for the value of immobilized biomass (results not shown), probably due
to incomplete removal of contaminating proteins contained in the medium or to interference
of peptidoglycans. Similar results were also observed for immobilized Acinetobacter
calcoaceticus cells (Wang 1988). In contrast, Chen et al. (1998) evolved and successfully
used a protein detection method for sludge biomass estimation of cells immobilized in
phosphorylated polyvinyl alcohol gel beads. Also Freeman et al. (1982) developed and
used an assay based on protein content determination in order to quantify immobilized
biomass in synthetic and native polymer-gel beads.
In ecological research the extraction and analysis of ATP is often used for biomass
estimation (Holm-Hansen and Karl 1987; Karl 1980). There are two important assumptions
for the use of this method: first, that ATP exists only in viable cells and is rapidly degraded
after the cell dies (Holm-Hansen and Karl 1987); and second, that the quantity of ATP in
the bacterial cell does not vary significantly for a particular strain (Stanley 1986). Thus, the
viable cell concentration can be estimated by the amount of cellular ATP. Gikas and
Livingston (1993) used ATP content and the dry weight of planktonic and immobilized
cells growing on 3,4-dichloraniline to evaluate cell viability. The biomass during
continuous culture on whey permeate of Lb. casei cells immobilized on sintered glass
particles was estimated by the estimation of cellular ATP (Krischke et al. 1991).
In our study, culture broth samples from free-cell cultures with Lb. rhamnosus RW-9595M
were analyzed for ATP content. Preliminary data showed that the amount of ATP per cell
decreased dramatically (from 1.2 · 10-19 to 2 · 10-20 mol ATP/CFU) during the exponential
growth phase (see Annexe 1 ). For this reason no further experiments were made with this
79
method. Chappelle et al. (1987) also pointed out that the ATP concentration in bacterial
cells varies over the growth cycle and decreases as the population ages.
Another important component of viable cells is DNA. The DNA extraction method was
used for biomass determination in the domain of waste water treatment (Raebel and
Schlierf 1980) and marine sediment characterization (Dell'anno et al. 1998). The
quantification of Acinetobacter calcoaceticus immobilized on Celite (Wang 1988) and
Comamonas acidovorans immobilized on different supports (Buchtmann et al. 1997) was
also tested by a DNA method.
In this study, the microbial DNA extraction and quantification method was used to estimate
biomass immobilized on ImmobaSil® carriers. Correlations between DNA content, dry
weight and free-cell counts of Lb. rhamnosus ATCC-9595 were first established. This low
EPS producer was used because Lb. rhamnosus RW-9595M, a natural mutant isolated from
Lb. rhamnosus ATCC-9595, produces very high amounts of EPS that interfere with cell
separation. Cell samples from the exponential growth phase of free-cell pH-controlled
batch cultures with concentrations from 1.7·108 to 1.3·1010 CFU/ml were used to develop
calibration curves between DNA content and dry weight or viable cell counts. Highly
significant (p<0.001) correlations were obtained:
Xw = 2.9594·109 · CDNA R2 = 0.9779 (2)
Xc = 1.2888 · CDNA R2 = 0.9739 (3)
where Xw and Xc are the viable cell count (CFU/ml) and dry biomass concentration
(mg/ml), respectively, and CDNA is the DNA concentration (µg/ml).
After extraction, the amount of DNA in colonized supports during the four consecutive
cultures was measured and used to estimate biomass growth in the supports. After only a
4-h stirring regime, an immobilized biomass of about 1.1 · 109 CFU/ml support was
measured, indicating the good adhesion properties of Lb. rhamnosus RW-9595M cells on
the silicon rubber supports (Fig. 3.2). The immobilized biomass grew continuously during
the four successive batch cultures and reached a very high value of
8.5 · 1011 CFU/ml support at the end of the fourth culture.
80
This result was obtained with the assumptions that DNA content of parental strain,
Lb. rhamnosus ATCC-9595, used for calibration of this method was the same as for the
EPS producing variant Lb. rhamnosus RW-9595M and that DNA content of immobilized
cells was the same as for cells produced during free-cell cultures. Lb. rhamnosus
ATCC 9595 was used for method calibration, because it produced only very low amounts
of EPS compared with the variant strain RW-9595M. The high production of EPS by this
strain prevented the separation of cells from the broth medium by physical techniques
(filtration, centrifugation), which is required for the development of a calibration curve for
the method. A very rapid degradation of DNA was observed for this culture with cell death
as a result of a very active DNA degrading enzyme (Peant and LaPointe 2001). Therefore,
the immobilized cell content estimated with this method mainly corresponded to living cell
DNA that was not degraded.
The viable immobilized biomass tested in our study (8.5 · 1011 CFU/ml support) is high,
compared with data previously reported for other LAB, although it is difficult to compare
data for immobilized biomass, because different microorganisms, immobilization
procedures, reactor designs and measurement methods were used. For example,
immobilized viable cell counts of 2.7 · 1011 CFU/ml gel beads for Lactobacillus casei
subsp. casei (Arnaud et al. 1992) and of 1.3 · 1011 CFU/g beads for three strains of
lactococci (Lamboley et al. 1997) immobilized in κ-carrageenan/locust bean gum gel beads
were measured during continuous fermentation. Modelling of the density of Lactococcus
lactis cells in gel matrix indicated that cell concentration at the bead periphery could reach
maximum values as high as 1 · 1012 cells/ml support (Cachon et al. 1995). Doleyres et al.
(2002b) also reported high bifidobacteria viable counts (6.8 · 1010 CFU/g) in gellan gum gel
beads during continuous cultures.
The established correlation between DNA content and dry biomass concentration was used
to estimate the bacterial dry weights in the carriers. The highest immobilized biomass value
of 384.9 ± 1.7 mg/ml was obtained after the fourth batch culture. This data is in agreement
with data on immobilized biomass dry weights in porous solid supports reported in the
literature. Lb. casei immobilized by adsorption on porous glass/ceramic beads for lactic
acid fermentation reached a biomass concentration of 0.105 g/g support during continuous
81
culture in whey permeate (Krischke et al. 1991). For Lb. casei cells immobilized on
polyethyleneimine-coated foam glass particles in a recycle batch reactor with a whey-based
medium, biomass concentration reached 0.490 g/g support after 12 cycles (Senthuran et al.
1997). In a study with Lb. rhamnosus immobilized on different inert adsorbent supports,
mainly made of porous glass, in a continuously recycled packed reactor, a maximum
immobilized biomass load of the support of 34.4 g dry weight/l was tested (Gonçalves et al.
1992).
The calculated total population in the ICT system after the first batch fermentation
(1.09 · 1014 CFU) was approximately eight fold higher than that for the free-cell system
(1.57 · 1013 CFU). This is unusual, since total populations in ICT systems are generally
lower than those in free-cell systems after a single batch fermentation (Champagne et al.
1993). This suggests that DNA data used to estimate the CFU population slightly
overestimates Lb. rhamnosus RW-9595M viable cell counts. It must be remembered that
the DNA-CFU relationship was established with the parent ATCC 9595 strain. After the
first batch, immobilized cells represented approximately 60% of the total population in the
ICT system. This is typical of data obtained in ICT systems following a first batch
fermentation (Champagne et al. 1993).
3.5.4 EPS production during repeated batch cultures with immobilized
cells
At the end of the fourth consecutive culture, which lasted only 7 h, a high total
polysaccharide content in the broth of 2176 ± 95 mg/l was obtained (Fig. 3.2), which
corresponded to an EPS production of 1808 ± 107 mg/l. At this time, the carbon source in
the medium, lactose, was completely consumed and the culture entered stationary growth
phase. It can be presumed that cell growth and/or EPS production could be further
enhanced by using a higher carbon concentration in SWP medium, such as 8% instead of
5% whey permeate in SWP. Even though batch cultures with immobilized cells were
limited by the carbon source, the high biomass maintained in the system more than doubled
the maximum EPS volumetric productivity (258 mg/l·h after 7 h during the fourth batch
culture) compared with free-cell batch cultures in 8% SWP (110 mg/l·h, calculated for an
82
EPS production of 1985.2 mg/l after 18 h culture). Considering interruption periods for
equipment cleaning and inoculum preparation, the EPS volumetric productivity of repeated
immobilized cell batch cultures is approximately 4–5 fold higher than for free-cell batch
cultures. Taking into account free and immobilized biomass, a specific productivity of
6.24·10-12 mg/CFU h was calculated for the fourth immobilized cell fermentation, which is
approximately 20% lower than that for free-cell batch fermentations (8.45·10-12 mg/CFU h).
This data can be explained by mass transfer limitations due to immobilization which create
a different microenvironment for immobilized cells compared with that for planktonic cells,
affecting not only nutrient uptake but also removal of products like lactic acid (Champagne
et al. 1994; Lamboley et al. 1997). Product accumulation may lower growth rate and
change the physiology of immobilized LAB cells (Cachon et al. 1998; Champagne et al.
1994; Krishnan et al. 2001).
3.6 Conclusions
In this study, a whey permeate-based medium was fermented by Lb. rhamnosus
RW-9595M for high EPS production. This is a promising approach for using whey
permeate, a by-product of the dairy industry available in large amounts and with limited
value. A method for biomass determination, based on extraction and quantification of
microbial DNA, was developed. This method was useful for the estimation of biomass in
solid supports, which cannot be quantified by traditional methods, such as biomass dry
weight or cell enumeration. Repeated batch cultures clearly showed the high potential of
immobilized cells on solid supports for EPS production, increasing the maximum
volumetric productivity compared with free-cell cultures. In addition, this technology
results in shorter shut-down periods of fermentation systems, with more than three
production batches per day, and reuse of microbial cells, which further enhances industrial
productivities. Our data shows the great potential of an immobilized cell system with this
strain for the production of EPS-type functional and eventually nutraceutical food
ingredients in a whey permeate-based medium. This system is currently being studied for
continuous EPS production in supplemented whey permeate medium.
Chapitre 4
Exopolysaccharide production during chemostat
cultures with free and immobilized Lactobacillus
rhamnosus RW-9595M
Dirk Bergmaier1, Claude P. Champagne2 and Christophe Lacroix3
1 STELA Dairy Research Centre, Pavillon Paul Comtois, Université Laval, Québec, PQ,
Canada, G1K 7P4
2 Food Research and Development Center, Agriculture and AgriFood Canada, St-
Hyacinthe, PQ, Canada, J2S 8E3
3 Laboratory of Food Biotechnology, Institute of Food Science and Nutrition, Swiss
Federal Institute of Technology, ETH Zentrum, LFO F18, CH-8092 Zurich, Switzerland
84
4.1 Résumé
La production d'exopolysaccharide par Lactobacillus rhamnosus RW-9595M a été étudiée
lors des fermentations continues dans un milieu à base de perméat de lactosérum. Lors
d'une culture avec des cellules libres à des taux de dilution (D) entre 0.3 et 0.8 h-1, une
production d'EPS (1808 mg/l) et une productivité volumétrique (542,6 mg/l·h) maximales
élevées ont été obtenues pour un bas D de 0.3 h-1, tandis que la productivité spécifique en
EPS était maximale (9.80 ± 1.01·10-11 mg/CFU·h) pour un D intermédiaire de 0.7 h-1. Une
fermentation continue dans un système de bioréacteurs à deux étages, avec les cellules
immobilisées, a été conduite pendant 32 jours. Le fermenteur du premier étage contenait
des cellules immobilisées par adsorption sur des supports poreux solides en caoutchouc de
silicone (ImmobaSil®). Le deuxième étage de fermentation en série a été constamment
inoculé par les cellules produites dans le premier étage. L'influence de la concentration en
extrait de levure, de la température et du taux de dilution sur les productions de la
biomasse, d'EPS et d'acide lactique dans les deux réacteurs a été étudiée, en utilisant un
plan central composite rotatif avec une analyse de surface de réponse. Un modèle
statistiquement significatif (P<0.05) a été trouvé seulement pour la production d'acide
lactique mais pas pour la production de biomasse ou d'EPS. Des concentrations moyennes
de cellules libres de 1.36 · 109 et 2.26 · 109 CFU/ml ont été déterminées dans le premier et
le deuxième réacteur. Une biomasse immobilisée très élevée et stable, égale à
5.3 ± 1.8 · 1011 CFU/g, a été mesurée par le dosage de l'ADN dans les supports solides. En
dépit de ces concentrations élevées en cellules libres et immobilisées, la production
moyenne en EPS soluble dans le milieu fermenté a été très basse (138 mg/l). Ce résultat
peut être expliqué par les changements morphologiques et physiologiques majeurs de
Lb. rhamnosus RW-9595M qui conduisent, après dix jours de fermentation, à la formation
d'agrégats d'une forte taille (1.2 millimètres) contenant des cellules. La perte de la capacité
des cellules à produire des EPS solubles, observée dans le système à cellules immobilisées,
était réversible et la production d'EPS a été entièrement récupérée après quatre cultures
successives en batch à pH contrôlé.
85
4.2 Abstract
Exopolysaccharide production by Lactobacillus rhamnosus RW-9595M was studied during
continuous fermentations in whey-permeate-based medium. A continuous culture with free
cells was conducted for 9 days at dilution rates (D) between 0.3 and 0.8 h-1. High maximum
EPS production (1808 mg/l) and volumetric productivity (542.6 mg/l h) were obtained for a
low D of 0.3 h-1, whereas the EPS specific productivity was maximum
(9.80 ± 1.01·10-11 mg/CFU h) for an intermediate D of 0.7 h-1. A continuous fermentation in
a two-stage bioreactor with immobilized cells was carried out for 32 days. The first
fermentation stage contained cells immobilized by adsorption on silicone rubber solid
porous supports (ImmobaSil®). The second fermentation stage in series was continuously
inoculated by cells released from the first stage. The influence of yeast extract
concentration, temperature and dilution rate on biomass, EPS and lactic acid production in
both reactors was investigated, using a central composite rotatable design and response
surface analysis. A statistically significant model (P<0.05) was found only for lactic acid
production but not for biomass and EPS production. The mean free cell concentrations,
measured by plate counts, in the first and second reactor was 1.36 · 109 and
2.26 · 109 CFU/ml, respectively. A very high and stable immobilized biomass was tested by
DNA quantification analysis in the solid supports, equal to 5.3 ± 1.8·1011 CFU/g support.
Despite these high free and immobilized cell concentrations, the mean soluble EPS
production in the fermented broth was very low (138 mg/l). This was explained by marked
morphological and physiological changes of Lb. rhamnosus RW-9595M that lead to the
formation of very large cell-containing aggregates (1-2 mm) after 10 days. The loss of
soluble EPS production capacity of cells in the effluent of the immobilized cell system was
reversible and EPS production was fully recovered after four successive pH-controlled
batch cultures.
4.3 Introduction
Exopolysaccharides (EPS) produced by lactic acid bacteria (LAB) have received
considerable attention in recent years. They play an important role in the manufacturing of
fermented dairy products such as yogurts, fermented milks, cheeses, fermented creams and
86
milk-based desserts (Duboc and Mollet 2001). The EPS are very attractive for use as food
additives because of their contribution to the texture, mouthfeel, taste perception and
stability of the final product. They may act as texturizers and stabilizers, decreasing
syneresis and improving product stability. Furthermore, EPS can contribute to human
health as prebiotics or due to their anti-tumor, anti-ulcer, immunomodulating or
cholesterol-lowering activities (Ruas-Madiedo et al. 2002a). However, compared to
dextran-producing or Gram-negative EPS producers, the low production of EPS by most
LAB is a constraint for their commercial use as food additives (De Vuyst and Degeest
1999b).
Immobilized cell technology (ICT) could be an attractive solution to overcome this
constraint. The retention of high biomass densities in continuous cultures can generate an
uncoupling between microbial growth and product synthesis and largely increases process
productivity (Norton et al. 1994a). Other advantages of ICT are the reuse of cells,
protection against shear damage and the high biological stability during long-term
continuous fermentation (Champagne et al. 1994; Lamboley et al. 1999; Lamboley et al.
1997). Furthermore, immobilized cell systems show enhanced tolerance for inhibiting
substances like acids, salts or antibiotics (Fortin and Vuillemard 1989; Jouenne et al. 1994;
Trauth et al. 2001). ICT results in more constant product characteristics and, in addition,
local accumulation of produced extracellular polysaccharides in the immobilization support
may facilitate their recovery and hence downstream processing for EPS production (Wang
and Wang 1989).
There are numerous studies with different techniques for immobilizing cells and, in this
way, to increase cell concentration in the bioreactor. Cell recycling with membrane
separation techniques (e.g. hollow fibre systems, membrane reactors) often encounter mass
transfer and membrane fouling problems (Gonçalves et al. 1992). These systems seem to be
unsuitable for the production of high molecular mass EPS. Polysaccharide gel entrapment
techniques have been extensively studied, especially with LAB, but the gels generally
exhibit limited mechanical stability over extended fermentation periods (Champagne et al.
1994). This limitation may be exacerbated during EPS fermentations that produce a highly
viscous medium. Immobilization by adsorption on porous preformed and inert supports can
87
solve this problem. Bergmaier et al. (2002a) (Chapitre 3) immobilized Lb. rhamnosus RW-
9595M cells by adsorption on ImmobaSil® porous solid supports during repeated batch
cultures in a whey-permeate-based medium. Immobilized biomass reached
8.5 · 1011 CFU/ml support after only four fermentation cycles and a very high maximum
EPS volumetric productivity of 258 mg/l·h was obtained for the forth cycle which lasted
7 h. This data shows potential for the use of immobilized cells on solid supports during
continuous fermentations for EPS production.
Whey is a by-product of cheese production which can be separated by ultrafiltration into
high-grade proteins and permeate. The whey permeate contains almost all the lactose of
milk and, if not treated, represents an important part of the polluting effluents of dairy
industries. Due to its high biological oxygen demand, its treatment by sewage plants is
expensive. This by-product could provide a carbon and mineral-rich substrate for microbial
fermentations. Whey-permeate-based media were used recently for high EPS production by
Lactobacillus rhamnosus RW-9595M (Bergmaier et al. 2001; Macedo et al. 2002b).
In this work, EPS production during chemostat cultures with free and immobilized
Lactobacillus rhamnosus RW-9595M at different dilution rates was studied in a
supplemented whey permeate medium. Cells were immobilized by adsorption on a food-
grade porous support of silicone rubber, ImmobaSil®. A second stage free-cell bioreactor
(FCB) attached in series with the immobilized cell bioreactor (ICB) was used to finish the
fermentation and to increase cell and product concentrations in the fermented broth. The
effects of yeast extract concentration (CYE), temperature (T) and dilution rate (D) and their
interactions were investigated on biomass, lactic acid and EPS productions during a 32-day
continuous immobilized-cell fermentation using a central composite rotatable design and
response surface analysis.
4.4 Material and Methods
4.4.1 Microorganism
Lb. rhamnosus RW-9595M, obtained from the Lactic Acid Bacteria Research Network
(RBL Network) culture collection (Dairy Research Centre STELA, Université Laval,
88
Québec, PQ, Canada), was isolated from reference culture Lb. rhamnosus ATCC-9595. It
was shown to produce very high EPS concentrations in BMM defined medium (Dupont et
al. 2000) and in supplemented whey permeate medium (Bergmaier et al. 2001; Macedo et
al. 2002b). The strain was subcultured aerobically in supplemented whey permeate for 36 h
at 37°C. The stock culture was kept frozen in 6% (v/v) rehydrated skim milk and 10% (v/v)
glycerol at -80°C. For inoculum preparation, a fresh culture was propagated twice in 5%
whey permeate with 1% yeast extract at 37°C for 10 h or until pH 4.8 was reached.
4.4.2 Culture media
The supplemented whey permeate medium (SWP) was obtained by rehydration of whey
permeate powder (8% w/v, Foremost, Baraboo, WI, USA), and addition of 0.5 g/l MgSO4 ·
7H2O, 0.05 g/l MnSO4 · H2O and 1 ml/l Tween-80. The pH was adjusted to 4.9 with HCl
6 N and the suspension was filtered on a filter press Flojet (Buon Vino, Cambridge, Ont,
Canada) with number 4 filters. The medium was heat-treated with a induction heat
exchanger (Chalinox; Sorel, Québec, Canada) at 140°C for 8 s, then cooled to 6°C. It was
stored at 4°C and supplemented with a concentrated sterile yeast extract (YE) solution prior
to use at a final concentration in the broth medium ranging from 0 to 1.37 % (w/v). The YE
solution was prepared by adding 400 g of YE (Rosell Institute Inc., Montreal, PQ, Canada)
to 1 l deionized water and autoclaved for 15 min at 121°C.
4.4.3 Fermentation techniques
4.4.3.1 Free-cell continuous culture
A continuous culture with free cells was carried out in SWP medium containing 1.1% YE
in a 0.5 l bioreactor (Model C30, New Brunswick Scientific Co. Inc., Edison, NJ), with a
fermentation volume of 0.5 l, temperature controlled at 37°C and pH at 6 by addition of 7 N
NH4OH. The reactor was inoculated at 1.5% (v/v) and batch fermentation was carried out
for 21 h. Then fresh medium was added at a dilution rate of 0.3 h-1 and the system was
equilibrated for 1 day. During the following 9-day continuous fermentation, dilution rates
between 0.3 and 0.8 h-1 were applied in randomized order. After at least ten reactor-volume
89
changes, steady-state conditions were considered established and effluent samples were
taken.
4.4.3.2 Immobilized-cell continuous culture
The immobilized cell fermentation was carried out in a two-stage system consisting of a
1.5 l Bioflow III bioreactor (New Brunswick Scientific Co. Inc., Edison, NJ) and a second
1.5 l bioreactor (Biogénie, Ste Foy, Qc, Canada). These reactors were set for a total culture
volume of 0.7 and 1.4 l, respectively. Temperature in both reactors was controlled at the
set-point selected in the range from 24 to 44°C. The pH was controlled on-line at 6 by
automatic addition of 7 N NH4OH. The first bioreactor (ICB) was operated with
immobilized cells, and the second reactor (FCB) in series was operated with free cells
released from the ICB.
The ICB was filled with 210 ml (corresponding to 30% of the total culture volume) silicone
rubber solid carriers (ImmobaSil®, Ashby Scientific Ltd., Coalville, Leicestershire, UK)
and 500 ml PBS at pH 7. Designed as Raschig-rings, these solid supports offer a uniform
pore size from 50 to 150 µm and a void fraction larger than 40% for colonization. The PBS
was replaced aseptically by fresh medium with a composition corresponding to the central
point of the experimental design (CYE = 0.7%). The pH was adjusted to 6 and the medium
was agitated for 20 min. This step was repeated once and the ICB was refilled with fresh
media. The pH was adjusted and controlled at 6 and temperature was set to 34°C with mild
agitation (25 rpm). The reactor was then inoculated (1.5% v/v) with a fresh culture. The
ICB was operated in batch mode under these conditions for 9 h, until optical density
(620 nm) of the media reached a value of 9. Then the medium feed was started at a dilution
rate of 0.5 h-1. When the medium volume in the second stage FCB reached the working
volume (1.4 l), pH and temperature were controlled at the same set-point as in the ICB and
the system was operated for 48 h with agitation at 110 rpm and for another 24 h under the
same conditions but with a D of 0.8 h-1. After this initial colonization period, the set points
for CYE, T and D were set to the central point values of the experimental design and the
system equilibrated for an additional 4 days. The values for D in this study are calculated
for the ICB working volume (0.7 l).
90
The set points for CYE, T and D in both reactors were changed every 24 h according to the
central composite experimental design (Tab. 1) and the fermentation was allowed to
stabilize for 20 h under the new conditions. After 20 and 22 h, samples were taken from the
effluent of the two reactors for cell enumeration, and sugar and lactic acid determinations.
At day 3 no sample was taken because the pH in the FCB differed by more than 0.1 from
the set point due to pH-probe deviation. The probe was changed and the system was re-
equilibrated for 24 h. Hence, the entire culture experiment lasted 32 days, 8 days for
colonization and equilibration and 24 days for the experimental design. Cell enumerations
were performed immediately after sampling. Samples were kept frozen at -18°C for the
determination of lactic acid and sugar concentrations. A sample of 15 colonized carriers
was taken 21 h after the set point changes and kept frozen at -80°C for determination of
immobilized biomass.
4.4.3.3 Successive free-cell batch cultures
Batch cultures with free cells were carried out in 0.5 l SWP medium with YE concentration
of 1.1% in a 0.5 l bioreactor (Model C30, New Brunswick Scientific Co. Inc., Edison, NJ).
Temperature was controlled at 37°C and pH at a value of 6 by addition of 7 N NH4OH. At
day 19 of the continuous immobilized cell culture, an effluent sample of the ICB was taken
to inoculate (1% v/v) the first batch culture. When the base consumption ceased, the batch
culture was stopped and the fermented broth was immediately cooled in ice-water. This
culture was taken to inoculate a second identical batch culture, and with the broth of the
second, a third identical batch culture was inoculated. At the end of each batch culture, the
viable cell and EPS concentrations were measured in the fermented broth.
4.4.4 Cell enumeration and biomass determination
Free-cell concentration in the effluent was estimated by the pour plate method on solid
MRS agar (Difco Laboratories, Richmond, CA, USA), after aerobic incubation at 37°C for
36 h. Reported data are means for triplicate analysis.
91
4.4.5 Determination of immobilized biomass concentration in solid
supports
For immobilized cell concentration determination, microbial DNA was extracted and
quantified as previously described (Bergmaier et al. 2002a) (Chapitre 3). Immobilized cell
concentration was expressed as colony-forming units or cell-dry-weight per support dry
weight (CFU/g or g/g, respectively). Each analysis was repeated three times.
4.4.6 EPS concentration analysis
Homogeneous culture broth samples were heated to 100°C for 15 min, cooled and
centrifuged (13,200 g at 4°C for 25 min). Supernatants were stored at -20°C.
Polysaccharides in supernatant were partially purified by a new ultrafiltration method
(Bergmaier et al. 2001) (Chapitre 2), and total carbohydrate was quantified by the phenol-
sulfuric acid method (Dubois et al. 1956) with glucose as standard. The concentration of
EPS produced during fermentation was calculated by subtracting the polysaccharide
concentration in the fresh medium from that measured in the fermented broth. Each
analysis was repeated at least three times. The experimental error was always less than
10%.
4.4.7 Sugar and organic acid analysis
Culture broth samples were centrifuged (13,200 g at 4°C for 25 min), diluted and filtered
on an Acrodisc LC13 filter, 0.2 µm (Gelman Sciences, Ann Arbor, MI, USA). Residual
sugar and lactic acid concentrations in the supernatant were determined by HPLC (Waters,
Millipore Co. Montreal, QC, Canada) using a Phenomenex ion column (Phenomenex,
Torrance, CA) and H2SO4 0.0064 N as eluent at a flow rate of 0.4 ml/min. Analyses were
performed in duplicate.
4.4.8 Microscopy observations
Microscopic preparations of free cells were stained with methylene blue and observed using
optical microscopy. Samples of support were fixed for 24 h in 0.1 M cacodylate buffer at
92
pH 7.3 with 1.5% paraformaldehyde, 2.5% glutaraldehyde, 0.5 mM CaCl2 and 0.12 M
sucrose. The samples were rinsed three times (20 min) with 0.1 M cacodylate buffer, and
treated with 1% osmium tetroxide in 0.1 M cacodylate buffer, for two hours at room
temperature and rinsed again three times with cacodylate buffer. The samples were
dehydrated using an ethanol dehydration series with 10 min each in 75, 80, 90, 96% ethanol
and three changes of 10 min in 99% ethanol. The dehydrated supports were embedded in
epon and sections (about 100 µm thick) were post-stained with methylene blue before
optical microscopy examination.
4.4.9 Experimental design and statistical analysis
A central composite rotatable design composed of 8 factorial points, 6 star points and 1
central point was used to study the effect of fermentation parameters on the continuous
immobilized cell fermentation. To estimate the experimental error and the time stability of
the fermentation, the central point was repeated 9 times. The experimental points were
randomized. Using response surface analysis, the effects of three factors, CYE, T and D,
with five levels each, and their interactions were examined. The real and coded values of
the independent variables are shown in Table 1. The statistical analysis was carried out
using the software JMP IN (SAS Institute Inc., version 3.2.6, Cary, NC). Two covariates
were used for the ANOVA. The first covariate (age) accounted for the time change of the
culture and corresponded to the time elapsed (days) since the first experimental point,
which was set to one. The second covariate (stop) accounted for an interruption of the
fermentation due to pumping problems and a change of the ICB outlet geometry at age 12.
This covariate was equal to 0 or 1, before or after the interruption, respectively. The
covariates were used to maximize the adjusted R2. The adjusted R2 was used instead of R2
to describe the total variance of the model because when the number of regressors is close
to the sample size, R2 is biased (SAS/STAT® 1989). A second order model was used to fit
the responses:
stop age*age age 6543
1
2
1
3
1
23
10 βββββββ ++++++= ∑∑∑∑
+==== ijjiij
iiiii
iii XXXXY
93
where Y is the dependent variable, Xi are the independent variables, βi and βij are the
regression coefficients for main effects and interactions of the independent variables,
respectively.
Seven dependent variables were studied: free cell counts, EPS and lactic acid productions
in the fermented broth in both bioreactors and immobilized biomass concentration in the
solid supports. Cell counts were transformed to their base 10 logarithms to stabilize the
variance and normalize the residuals. A response surface model was calculated for each
response. The sum of square (SS) of the model was partitioned into linear, quadratic, and
crossproduct SS and further into the SS for each factor. The effect of each factor on the
model was estimated from the fraction in the total SS that was associated with this effect.
The coefficients (βi and βij) were determined by the least square method of fitting.
4.5 Results
4.5.1 Free-cell chemostat cultures
Biomass and EPS production by Lb. rhamnosus RW-9595M in SWP medium were studied
during a 9-day chemostat culture with free cells, operated with different dilution rates
between 0.3 and 0.8 h-1 (Fig. 4.1). The cell concentration in the fermented broth decreased
from 1.44 · 1010 to 1.52 · 109 CFU/ml with D in the tested range. The fermentation product
concentrations, lactic acid and EPS, decreased from 33.2 to 12.1 g/l (data not shown) and
from 1808 ± 125 to 125 ± 100 mg/l, respectively, for increasing D from 0.3 to 0.8 h-1. On
the other hand, lactose concentration increased from 20.4 to 43.9 g/l with increasing D,
corresponding to lactose utilization of 51 and 19%, respectively. The EPS production was
significantly (p<0.001) correlated with cell concentration with a Pearson correlation
coefficient r of 0.9997. The EPS volumetric productivity was maximum
(542.6 ± 37.5 mg/l h) for a low D of 0.3 h-1, which corresponded to maximum EPS
production (1808 ± 125 mg/l). However, the specific productivity increased with D up to a
maximum of 9.80 ± 1.01·10-11 mg/CFU·h for a D of 0.7 h-1, and then decreased with further
increase in D to 0.8 h-1.
94
Fig. 4.1 Viable cell counts (vertical bars), EPS concentration (●), and EPS volumetric (■)
and specific productivities (▲) during free-cell chemostat culture with Lb. rhamnosus
RW9595M for different dilution rates. Means and standard deviations for two replications
of D.
4.5.2 Immobilized-cell chemostat cultures
A continuous culture was carried out in a two-stage fermentation system with cells
immobilized on solid supports in the first reactor (ICB) and the second reactor (FCB)
continuously inoculated with cells released from the ICB. The influence of yeast extract
concentration, temperature and dilution rate on biomass, EPS and lactic acid production in
both bioreactors and on immobilized biomass was investigated during continuous
fermentation in SWP, by changing fermentation conditions every 24 h according to the
rotatable central composite experimental design (Tab. 4.1). The results are shown in
Annexe 2 .
95
Tab. 4.1 Real and coded values of the central composite experimental design for the continuous immobilized cell fermentation.
Coded values Real values
CYE T D CYE
(% w/v)T
(°C) D*
(h-1) Factorial points - - - 0.3 28 1.2 - - + 0.3 28 2.4 - + - 0.3 40 1.2 - + + 0.3 40 2.4 + - - 1.1 28 1.2 + - + 1.1 28 2.4 + + - 1.1 40 1.2 + + + 1.1 40 2.4 Star points 0 0 + 0.7 34 2.8 0 0 - 0.7 34 0.8 0 + 0 0.7 44.1 1.8 0 - 0 0.7 23.9 1.8 - 0 0 0 34 1.8 + 0 0 1.37 34 1.8 Central points ** 0 0 0 0.7 34 1.8 * D is calculated for the ICB culture volume of 0.7 l. ** The central point was repeated 9 times to estimate experimental error and time stability during the 32-day culture.
4.5.2.1 Free and immobilized biomass production
The colonization of the ImmobaSil® carrier was analyzed by optical microscopy
observations of semi-fine slices of the carrier which were stained with methylene blue (Fig.
4.2). A very good colonization of the pores near the surface with a clear cell concentration
gradient within the support was observed. Nevertheless, a high cell density was also
visualized in the inner pores of the Raschig-Rings shaped support.
96
Fig. 4.2 Optical micrograph (10X) of a semi-fine slice (methylene blue staining) of the
ImmobaSil® support colonized with Lb. rhamnosus RW-9595M after 7 day chemostat
culture.
The immobilized biomass on ImmobaSil® carriers was estimated by extraction and
quantification of DNA. Correlation between DNA content, dry weight and cell counts
calculated by Bergmaier et al. (2002a) (Chapitre 3) were used to convert DNA data to
viable cell and biomass concentration. Immobilized biomass concentration was very stable
during continuous fermentation, with a mean of 5.3 ± 1.8·1011 CFU/g or 0.23 ± 0.08 g/g
support dry weight corresponding to 3.7 ± 1.2·1011 CFU/ml support. There was no
significant change of these parameters with time and no significant effect (p<0.1) of the
independent variables on immobilized biomass.
Immediately after the colonization and equilibration period, a morphological change of the
cells in the medium in both reactors was observed by optical microscopy. Especially in the
FCB, the normally short chains of lactobacilli of up to 4 cells (Fig. 4.3b) became more
elongated and formed a network-like structure (Fig. 4.3a). After 10 days of culture, the
massive formation of aggregates, very similar in appearance to kefir grains, was observed
in both bioreactors. These aggregates with a size of about 1-2 mm could be harvested by
simply sieving the effluent of the FCB on a screen (0.5 mm mesh size).
97
The mean viable free-cell concentrations were 1.36 ± 0.91 · 109 and
2.26 ± 1.96 · 109 CFU/ml in the ICB and FCB, respectively. For viable-cell counts in the
medium of the ICB, the addition of any covariate did not result in an increase in the
adjusted R2, which was only 0.21. The addition of the covariates stop, age and age2 to the
model for viable-cell counts in the medium of the FCB increased the adjusted R2, but only
to 0.12. In both cases, the regression models were not significant (p>0.1).
a) b)
Fig. 4.3 Photomicrograph of Lb. rhamnosus RW-9595M: a) in the FCB effluent after
14 days of chemostat culture (63X) b) in the fermented medium at the end of a free-cell
batch culture (100X).
4.5.2.2 Sugar and product concentration
Lactose was the only carbon source for fermentation, with an initial concentration in the
fresh medium of 63.0 ± 0.9 g/l. Lactic acid was the only organic acid produced by the
strain, with concentrations in the range from 4.0 to 38.1 and 5.2 to 51.4 g/l in the ICB and
FCB, respectively, with no lactic acid detected in the fresh medium by HPLC. For the ICB,
the addition of covariates age and stop in the model for lactic acid concentration resulted in
a high adjusted R2 of 0.94. The model was highly significant (p<0.001) and explained 97%
of the observed variations. Main effects of CYE and D and the covariate age were highly
significant (p<0.001), whereas the interaction D* CYE and covariate stop were significant at
a level of 99 and 95%, respectively. The linear factors CYE and D explained 13.6 and 41.1%
of the total variation, respectively. The covariates explained 59.3% with the covariate age
98
alone explaining 54.9% of the total variation. The effect of age on lactic acid concentration
in the ICB was linear, with a maximum correction of 30.3 g/l at age = 24 days, i.e. at the
end of the continuous culture. The covariate stop subtracted a constant equal to 6.2 g/l from
lactic acid concentration after age = 12 days. To illustrate the effect of the significant
factors CYE and D on lactic acid concentration in the ICB, a response surface was plotted
for T = 34°C and age = 12 days (Fig. 4.4). Lactic acid concentration increased with
increasing CYE at low D to a maximum of 32 g/l for CYE = 1.37% and D = 0.8 h-1, whereas
at high D, it decreased with increasing CYE. For high CYE, a drastic decrease in lactic acid
concentration was observed with increasing D.
For lactic acid concentration in the FCB, the addition of covariates stop, age and age2
resulted in a model with an adjusted R2 of 0.92. The regression model was highly
significant (p<0.001) and explained 96% of the observed variations. The main factors D
and CYE were significant at a level of p<0.001 and p<0.05, respectively. Also, the
covariates age and stop significantly (p<0.05) affected lactic acid concentration in the FCB.
The main effects of D and T explained 35.9 and 6.7%, respectively, whereas the covariates
together accounted for 24% of the observed total variation. The parabolic time correction
for lactic acid concentration was maximum for age 24 days (end of culture), adding 29.3 g/l
to the lactic acid concentration in the FCB, whereas covariate stop added 12.1 g/l after
age = 12 days. The response surface model for lactic acid concentration in the FCB was
plotted as a function of CYE and D, for T = 34°C and age = 12 days (Fig. 4.5). Lactic acid
concentration increased with increasing CYE and decreased with increasing D, with a
maximum of 46.5 g/l for CYE = 1.37% and D = 0.8 h-1.
The regression models for soluble EPS production in the ICB and FCB were not significant
(p>0.1), with very low adjusted R2 of –0.09 and 0.07, respectively. Mean soluble EPS
production in the ICB and FCB calculated for the entire experiment were very low, equal to
108 ± 90 and 30 ± 142 mg/l, respectively.
99
Fig. 4.4 Response surface of lactic acid concentration in the first immobilized-cell
bioreactor (ICB) for T = 34°C, covariates stop = 0.5 and age = 12 days.
100
Fig. 4.5 Response surface of lactic acid concentration in the second free-cell bioreactor
(FCB) for T = 34°C, covariates stop = 0.5 and age = 12 days.
101
4.5.3 Successive batch fermentations with cells from immobilized cell
culture
An effluent sample of the ICB was taken at age 19 days to inoculate (1% v/v) a 500 ml
batch fermentation with the same medium and incubation was carried out at pH 6 and
37°C. After 22 h the base consumption ceased and the culture was stopped. During the 22-h
culture, the viable cell concentration increased from 1.38 · 107 to 1.05 · 1010 CFU/ml.
Subsequently, this culture was used to inoculate a second batch (18 h) and then a third
batch culture (19 h). The maximum cell concentration at the end of the second and third
batch culture was 1.12 and 1.75 · 1010 CFU/ml, respectively. The EPS production in the
fermented broth increased progressively with the number of batch cultures, with 677 ± 14,
1044 ± 19 and 1742 ± 96 mg/l for the first, second and third culture, respectively.
4.6 Discussion
A continuous free-cell chemostat culture for EPS production was conducted in a
supplemented whey permeate medium, with pH and temperature set-points (6 and 37°C)
chosen from a previous study for high cell growth and EPS production with Lb. rhamnosus
RW-9595M (Macedo et al. 2002b). The high D values tested (between 0.3 and 0.8 h-1)
resulted in high residual lactose concentrations in the broth between 20 and 44 g/l, and
lactic acid production up to 33 g/l. In this range neither lactose nor lactic acid concentration
were inhibitory, as the strain showed good growth in lactose rich medium (62 g/l) and for
lactic acid concentrations above 41 g/l (Macedo et al. 2002b). In this study, a high EPS
production of 1808 mg/l for a low D of 0.3 h-1 was obtained and EPS concentration
decreased with increasing D (Fig. 4.1).
There are only a few reports on continuous cultures of LAB for EPS production. Grobben
et al. (1997) investigated the continuous EPS production with Lactobacillus delbrueckii
subsp. bulgaricus NCFB 2772 on different carbon sources. A maximum EPS concentration
of only 95 mg/l was obtained at a very low dilution rate of 0.075 h-1. Marshall et al. (1995)
studied EPS production by Lactococcus lactis subsp. cremoris LC330 during chemostat
culture. The production of two EPS was observed, one with a low (<10 kDa) and one a high
102
molecular mass (>106 Da). The maximum concentration for the high molecular mass EPS
of 92 mg/l was measured for low temperature and under nitrogen limitation, but the dilution
rate was not given. Gassem et al. (1997b) studied chemostat cultures for EPS production
with Lactobacillus debrueckii subsp. bulgaricus RR in a sweet whey based medium. The
maximum EPS concentration was 2130 mg/l for the higher tested D of 0.055 h-1,
corresponding to a volumetric productivity of 0.11 g EPS/l h. One has to be careful when
comparing EPS production between different studies because different quantification
techniques may result in considerable differences in EPS measures (De Vuyst and Degeest
1999b). In our study we used an accurate EPS quantification technique which is based on
the partial purification of the polymer by ultrafiltration and takes into account the
polysaccharide concentration in the fresh medium (between 0 and 573 mg/l, depending on
yeast extract supplementation level). Compared with that of Cerning et al. (1994), this
method has the advantages of accuracy and rapidity, and requires only small sample
volumes of 1 to 5 ml (Bergmaier et al. 2001) (Chapitre 2).
Both very high EPS production and volumetric productivity (542.6 mg/l h) were obtained
during chemostat culture with free cells of Lb. rhamnosus RW-9595M for a D of 0.3 h-1
(Fig. 4.1). This is by far the highest productivity reported in the literature for lactobacilli.
The specific productivity was maximum (9.80 · 10-11 mg/CFU·h) for a D of 0.7 h-1, and
decreased for higher D of 0.8 h-1. This decrease is supported by the theory of Sutherland
(1982) stating that there is a competition between EPS and cell-wall polymer
(peptidoglycan, teichoic acids, lipopolysaccharides) biosynthesis for the isoprenoid
glycosyl lipid carriers, and consequently EPS production is not growth-associated. For
mesophilic LAB strains, EPS production kinetics is generally not growth-associated (De
Vuyst and Degeest 1999b). In contrast, in our study EPS production during continuous
culture at different D was highly correlated with that for the viable cell concentrations, with
a Pearson correlation coefficient of 0.9997. This data indicates growth-associated EPS
production kinetics in these conditions.
The high EPS production by Lb. rhamnosus RW-9595M during batch cultures in whey
permeate based medium, up to 2775 mg/l (Macedo et al. 2002b), and during free-cell
chemostat cultures in this study, shows the high potential of this strain for EPS production.
103
Furthermore, uncoupling between EPS production and cell growth was observed with this
strain at temperatures between 32 and 42°C (Macedo et al. 2002a). These characteristics
support the use of cell immobilization for EPS production in a high-cell density reactor.
Indeed, cell immobilization often results in enhanced productivities and permits the
uncoupling of cell growth and metabolite production, as demonstrated for lactic acid
production at low yeast extract concentrations (Norton et al. 1994a). Norton et al. (1994b)
showed that cell immobilization permitted lowering of the yeast extract concentration in the
medium which has a very large economic impact on industrial lactic acid production
(Norton et al. 1994b). This can be of advantage for the production of EPS, because YE and
other nitrogen-rich supplements often contain polysaccharides that are very difficult to
separate from EPS (Bergmaier et al. 2001; Torino et al. 2000).
In this study, the mucoid properties of the strain were used to immobilize the cells by
adsorption on food-grade porous supports made of silicone rubber, ImmobaSil®. There are
some advantages of cell adsorption on solid porous supports, compared to other
immobilization techniques and particularly entrapment in gel matrices, that is widely used.
The immobilization step can be carried out in situ, does not involve tedious techniques and
is not harmful for the micro-organisms. Moreover, the solid supports offer high mechanical
stability during long term fermentation in systems with high shear stress, they are more
resistant to the compression and disintegration that can occur in packed beds and stirred
vessels and can be easily separated from the viscous fermented broth containing EPS.
During the 32-day chemostat culture, no mechanical or chemical degradation of the
supports were observed.
The ImmobaSil® porous support offered a very high cell retention capacity. Microscopical
observations showed high biomass accumulation, even in the inner pores of the support
(Fig. 4.2). In fact, with large pores between 50 and 150 µm, immobilization on ImmobaSil®
lies between flocculation and entrapment. During the colonization step, cell adsorption on
the support matrix is an important first step. Growth and aggregation of cells in the
quiescent zones resulted in complete filling of the outer pores of the carrier with biomass.
In these aggregates, cells are immobilized by cell-to-cell interactions and entrapment in the
extracellular substances, such as EPS. The DNA extraction and quantification technique,
104
used in this study, measured a very high and stable biomass content in supports during the
experiment, equal to 5.3 ± 1.8·1011 CFU/g support or 0.23 ± 0.08 g dry weight/g support.
This result was based on the assumptions that the DNA content in the parental strain with a
very low EPS production, Lb. rhamnosus ATCC-9595, used for calibration, is the same as
in Lb. rhamnosus RW-9595M, and that the DNA content in immobilized cells is the same
as in cells from free-cell cultures (Bergmaier et al. 2002a) (Chapitre 3). A very rapid
degradation of DNA was observed for this culture with cell death as a result of a very
active DNA-degrading enzyme (Peant and LaPointe 2001). Therefore, the immobilized cell
content estimated with this method can be attributed mainly to living cells for which DNA
was not degraded. This method proved to be very useful for the estimation of biomass in
solid supports that cannot be quantified by more conventional methods, such as biomass
dry weight or cell enumeration.
The very high viable immobilized biomass tested in our study is in general agreement with
data reported in the literature as previously discussed by Bergmaier et al. (2002a) (Chapitre
3). In this previous study of repeated-batch cultures with the same strain immobilized on
ImmobaSil® a maximum immobilized biomass concentration of 8.5·1011 CFU/ml support
was observed.
In the present study, immobilized cells were used in a two-stage fermentation system with a
first stage ICB and a second stage FCB, during a 32-day chemostat culture. The response
surface analysis of CYE, T and D did not show significant effects of these parameters on
free-cell biomass concentration in both reactors. This data was unexpected because a
similar design was used to study the production of concentrated mixed cultures in a
continuous reactor with three lactococcal strains immobilized separately (Lamboley et al.
1997). In addition, the independent variables, CYE, T and D, studied over wide value
intervals are known to have large effects on fermentation kinetics of LAB (Krischke et al.
1991; Lamboley et al. 1997; Norton et al. 1994a; Norton et al. 1994b). On the other hand,
the immobilization of living cells provides a cell reservoir for continuous fermentation and
allows stable operation of the continuous fermentation even at D higher than the maximum
specific growth rate of the culture. The absence of influence of D on free-cell counts
observed in this study, could partly be due to a large morphology change of the culture as a
105
result of immobilization. The extensive chain length elongation (Fig. 4.3a), similar to that
observed with different immobilized cell cultures (Barbotin et al. 1989; Gonçalves et al.
1992; Norton et al. 1993; Senthuran et al. 1997), resulted in underestimation of biomass by
the pour plate enumeration method. One counted colony corresponds to approximately two
to four cells with normal cell morphology produced during batch and continuous free-cell
cultures (Fig. 4.3b). However, it corresponded to a much larger number of cells that are
contained in one chain or aggregate during continuous immobilized cell culture. The
statistical model could not describe the viable cell count data even with the addition of a
covariate age. Nevertheless, the average free-cell concentrations in the fermentation broth
of the ICB (1.36 · 109 CFU/ml) and the FCB (2.26 · 109 CFU/ml) were high, showing the
high cell production capacity of the immobilized cell system.
Among the dependent variables tested, the response surface analysis found a statistically
significant model only for lactic acid concentration in the two reactors. In both reactors the
main factors CYE and D significantly influenced the lactic acid concentrations, whereas T
had no effect (see Annexe 3 ). Lactic acid concentration in the fermentation broth of both
reactors was maximum at low D and high CYE (Fig. 4.4 and Fig. 4.5), which is consistent
with literature data on lactic acid production with immobilized cells (Norton et al. 1994a).
The maximum predicted lactic acid volumetric productivity of the two stage fermentation
system (14.4 g/l h) was obtained for high D (2.8 h-1) and CYE (1.4 %) values, and was much
higher than that measured during free-cell continuous (9.9 g/l h for D = 0.3 h-1) or batch
culture with the same strain (2.75 g/l h after 20 h culture; (Bergmaier et al. 2002a)
(Chapitre 3). The covariate age, which accounted for time change during the continuous
fermentation, explained a large fraction of the total variation of lactic acid concentration in
the ICB (54.9%) and FCB (11.4%). This large effect of time on lactic acid production in
this study is different from the high stability observed during 5-7 week continuous cultures
with immobilized lactococci (Lamboley et al. 1997; 1999; 2001) and 90-day continuous
culture with immobilized Lb. helveticus (Norton et al. 1994a; 1994b). This difference could
be explained by changes in morphology of the culture which resulted in the retention of cell
aggregates and increased cell load in both reactors with time.
106
As for free-cell concentration, the models for soluble EPS production in both bioreactors
were not statistically significant. The mean soluble EPS productions of 108 ± 90 and
30 ± 143 mg/l in the ICB and FCB, respectively, were very low compared with that
obtained during batch and continuous free-cell cultures with the same strain. Lb. rhamnosus
RW-9595M has been shown to produce high amounts of EPS of 1718 mg/l during pH-
controlled batch cultures in the same medium (Bergmaier et al. 2001) (Chapitre 2) or
2775 mg/l in whey permeate supplemented with yeast extract and with components of the
BMM defined medium (Macedo et al. 2002b), and up to 1808 mg/l during continuous free-
cell cultures in this study. Even though the error on EPS quantification was low (<10%), a
large variation of EPS concentrations was observed. This variation could be explained by
the complex effects of the independent variables and time, the low EPS production and the
significant amount of polysaccharide, introduced by YE supplementation of the medium,
resulting in 0 to 572 mg/l polysaccharide concentration in the fresh medium, according to
the YE supplementation level. These high variations and low production could partly
explain the absence of a significant model for EPS production.
However, a main explanation for the very low EPS production with immobilized cells in
this study could be associated with a physiological change of the culture due to
immobilization, which resulted in the formation of macroscopic aggregates containing a
large amount of insoluble EPS (Bergmaier and Lacroix 2002) (Chapitre 5). To test the
hypothesis of a reversible physiological change, a pH-controlled batch culture in the same
medium was inoculated with cells from the immobilized cell system. The EPS
concentration at the end of the first batch culture was 677 ± 14 mg/l, which is intermediate
between that for immobilized cells and that for batch fermentations with free cells
(1718 mg/l). Cells from the first batch culture were then used to inoculate a second batch
and then a third batch culture. The EPS production increased progressively with the number
of batch cultures, with 1044 ± 19 and 1742 ± 96 mg/l at the end of the second and third
culture, respectively. These data clearly showed the reversibility of the physiological
changes of the culture caused by cell immobilization. In contrast, a gradual and irreversible
change in the production of a rhamnose-containing cell wall polysaccharide by different
Lactobacillus casei subsp. rhamnosus strains was observed during continuous free-cell
fermentations (Wicken et al. 1983). The authors hypothesized that the phenotypic
107
variability and the gradual loss of ability to produce this EPS on prolonged cultivation may
both depend on a common genetic feature, which is only found in certain strains of Lb.
casei subsp. rhamnosus.
A clear morphological change of the cells was also observed during the early phase of the
continuous immobilized cell culture. This resulted in the formation of a network-like
structure at the microscopic scale but also in the formation of large aggregates. After
12 days, these aggregates obstructed the outlet screen of the ICB which had to be changed
for a larger one that did not retain the aggregates. In the FCB these aggregates, similar in
appearance to kefir grains, grew to a size of about 1-2 mm and could be harvested simply
by sieving the fermented medium on a screen (0.5 mm mesh size). A spontaneous
formation of aggregates by Clostridium butyricum and Lactobacillus laevolacticus at high
D during prolonged continuous free-cell culture was also reported by Teixeira de Mattos et
al. (1994). The authors also observed a decreased sensitivity to the adverse effects of
butyric acid for aggregated Clostridium butyricum. In contrast to free cells of Lactobacillus
laevolacticus, for which lactic acid is a positive effector of its own production, the
aggregated cells did not exhibit a relationship between the specific lactic acid production
rate and lactic acid concentration. The production and composition of aggregates by
immobilized Lb. rhamnosus RW-9595M have been reported in a separate paper (Bergmaier
and Lacroix 2002) (Chapitre 5).
4.7 Conclusions
This study clearly showed the high EPS production by Lb. rhamnosus RW-9595M during
continuous free-cell chemostat cultures. Maximum EPS productions of 1808 ± 125 mg/l
and volumetric productivities of 542.6 ± 37.5 mg/l h were obtained for a dilution rate of 0.3
and 0.7 h-1, respectively, and are among the highest values reported in literature.
Lb. rhamnosus RW-9595M was successfully immobilized by adsorption on ImmobaSil®
solid porous carriers and used during long term chemostat culture. Despite the very high
immobilized and free-cell biomass attained in this system and the high metabolic activity of
the culture shown by lactic acid production data, a very low amount of soluble EPS was
produced. This low production could mainly be attributed to a physiological change in the
108
culture due to immobilization. Repeated batch cultures, inoculated with cells produced in
the immobilized cell system, showed that this physiological change was reversible.
Eventually, this feature can be exploited for the production of EPS producing starters. Low
EPS concentration in the fermented broth would result in lower viscosity and facilitate cell
propagation and separation. An important morphological change of the culture was also
observed. The normally short chains of lactobacilli grew and formed a network-like
structure. Furthermore, the formation of macroscopic aggregates was observed after 10
days.
Chapitre 5
Aggregate formation during chemostat culture with
immobilized Lactobacillus rhamnosus RW-9595M
Dirk Bergmaier1, and Christophe Lacroix2
1 Dairy Research Centre STELA, Pavillon Paul Comtois, Université Laval, Québec, PQ, Canada,
G1K 7P4
2 Laboratory of Food Biotechnology, Institute of Food Science and Nutrition, Swiss Federal
Institute of Technology, ETH Zentrum, LFO F18, CH-8092 Zurich, Switzerland
110
5.1 Résumé
Afin de produire des exopolysaccharides, une culture continue de 32 jours dans un système de
bioréacteurs à deux étages a été conduite dans un milieu de perméat de lactosérum supplémenté.
Le premier bioréacteur contenait des cellules de Lactobacillus rhamnosus RW-9595M
immobilisées sur des supports poreux solides en caoutchouc de silicone (ImmobaSil®). Le
deuxième bioréacteur a été continuellement inoculé avec des cellules produites dans le premier
réacteur. Un changement physiologique et morphologique majeur de la souche a été observé,
ayant pour résultat une production très basse d'EPS soluble et la formation d'agrégats
macroscopiques (1-2 millimètres) après 10 jours de culture en continu. Avec le temps, les
agrégats se sont accumulés dans le premier et dans le deuxième réacteur et ont atteint des
concentrations moyennes respectives de 33.9 et 54.8 g/l, lors des 5 derniers jours de la
fermentation. La concentration d'agrégats dans l'effluent du système à deux étages a variée entre
3.16 et 28.59 g/l selon les conditions et le temps de la fermentation, résultant en une productivité
volumétrique d'agrégats entre 5.68 et 49.54 g/l·h. L'analyse chimique des agrégats a indiqué une
teneur élevée en azote du 10.10 ± 0.1 % (w/w), ce qui correspond à une biomasse totale de
73.8 % du poids sec de l'agrégat. La teneur élevée des agrégats en polysaccharides (14.2 ± 1.6 %)
a été attribuée à la production d'un EPS non-soluble par la culture immobilisée. Une biomasse
viable très élevée et relativement stable dans les agrégats de 4.32 · 1012 ± 0.97 · 1012 CFU/g a
également été mesurée par une méthode d'extraction d'ADN. Les agrégats produits pendant la
culture continue avec des cellules immobilisées dans un milieu de perméat de lactosérum
supplémenté, peuvent être facilement séparés et employés comme produit synbiotique, avec des
concentrations en cellules actives et en EPS très élevées.
5.2 Abstract
A 32-day chemostat culture in a two-stage fermentation system was conducted in a supplemented
whey permeate medium for exopolysaccharide production. The first bioreactor contained
Lactobacillus rhamnosus RW-9595M immobilized on solid porous supports, made of silicone
rubber (ImmobaSil®). The second bioreactor was continuously inoculated with cells released
from the first reactor. A large physiological and morphological change in the strain was observed
resulting in a very low soluble EPS production and the formation of macroscopic aggregates
111
(1-2 mm) after 10 days continuous culture. Aggregates accumulated with time in the first and
second reactor and reached mean dry weight concentrations for the last 5 days of 33.9 and
54.8 g/l broth, respectively. Aggregate concentration in the effluent of the two-stage system
varied between 3.16 and 28.59 g/l, for an aggregate volumetric productivity of the two-stage
system ranging from 5.68 and 49.54 g/l h for different fermentation conditions and time.
Chemical analysis of aggregates indicated a high nitrogen content of 10.12 ± 0.1 % (w/w), which
corresponds to a total biomass of 73.8 % of aggregate dry weight. The high polysaccharide
content of the aggregates (14.2 ± 1.6%) was attributed to the production of a non-soluble
exopolysaccharide by the immobilized culture. A very high and relatively stable viable biomass
in aggregates of 4.32·1012 ± 0.97·1012 CFU/g was also measured by a DNA extraction method.
The aggregates produced during continuous immobilized cell culture in supplemented whey
permeate can be easily separated and used as a symbiotic product with very high active cell and
EPS concentrations.
5.3 Introduction
Immobilization has been used for a long time for the production of vinegar with acetic acid
bacteria immobilized on wood chips (Ramakrishna and Prakasham 1999) or in Kefir production
with co-immobilized yeast and lactic acid bacteria (Champagne et al. 1994). Immobilized cell
technology (ICT) offers many advantages when compared with free-cell cultures like enhanced
fermentation productivity and cell stability via continuous operation and reuse of cells, retention
of plasmid bearing cells, enhancement of the production of secondary metabolites and protection
of cells against shear damage (Champagne et al. 1994). Furthermore it has been reported that
immobilized cell systems may be less susceptible to phage attack (Champagne et al. 1994) and
contaminating microorganisms (Navrátil and Sturdíc 1999). Due to these advantages of
immobilized cell technology (ICT) compared with free-cell cultures, various immobilization
techniques have been developed. To immobilize living cells, cells can be attached to a surface,
entrapped within a porous matrix, contained behind a barrier or self-aggregated. All these
immobilization techniques imitate what takes place in a natural environment, where cells are
almost always associated with surfaces and grow in a biofilm (Dunne 2002).
112
Cell immobilization has been shown to result in large physiological changes of the culture,
including shift from homo- to heterofermentative behavior (Krishnan et al. 2001; Smith et al.
1993), increased tolerance to product inhibition (Fortin and Vuillemard 1989; Krisch and Szajani
1997; Teixeira de Mattos et al. 1994) or even increased resistance to an antibiotic (Jouenne et al.
1994). Morphological changes of immobilized cells have also been observed (Gonçalves et al.
1992; Norton et al. 1993; Senthuran et al. 1997). Recent works on biofilm formation have
identified many surface-sensing mechanisms of bacteria (Prigent-Combaret et al. 1999; Wen and
Burne 2002). It has been shown that the interaction with surfaces can change microbial
metabolism, phenotype and morphology (O'Toole et al. 2000b; Parsek and Greenberg 2000;
Rashid et al. 2000) which may result in an increase in the glycocalyx production, which is mainly
composed of bacterial exopolysaccharides (Dunne 2002).
In a previous paper a chemostat culture for exopolysaccharide production with immobilized
Lb. rhamnosus RW-9595M was described (Bergmaier et al. 2002b) (Chapitre 4). The continuous
culture was carried out in a two-stage fermentation system with immobilized cells in the first
reactor (ICB) and the second reactor (FCB) was continuously inoculated with cells released from
the ICB. Despite the very high immobilized and free-cell biomass attained in this system and the
high metabolic activity of the culture shown by high lactic acid production, a very low amount of
soluble EPS was produced. This low production was mainly attributed to a physiological change
of the culture due to immobilization. In this paper, we report the morphological change observed
during a 32-day culture, with increased bacterial chain length and formation of large (1-2 mm)
cell-containing aggregates. The production of these aggregates was measured during continuous
culture with the two-stage ICB/FCB system operated with different conditions and the aggregate
structure and composition were analyzed.
5.4 Material and Methods
5.4.1 Microorganism and culture conditions
A 32-day continuous culture with Lb. rhamnosus RW-9595M was carried out in a two stage
fermentation system consisting of two stirred-tank reactors in series, as described previously
(Bergmaier et al. 2002b) (Chapitre 4). The first immobilized cell bioreactor (ICB) contained 210-
ml solid carriers (ImmobaSil®; Ashby Scientific Ltd., Coalville, Leicestershire, UK)
113
immobilizing cells, for a total fermentation volume of 0.7 l. The second free-cell bioreactor
(FCB) of a working volume of 1.4 l, was continuously inoculated by cells released from the ICB.
Fermentation was carried out in a supplemented whey permeate (SWP) medium. Whey permeate
powder (Foremost, Baraboo, WI, USA) was rehydrated (8% w/v), 0.5 g/l MgSO4 · 7H2O, 0.05 g/l
MnSO4 · H2O and 1 ml/l Tween-80 were added, pH was adjusted at 4.9, and the medium was
filtered and sterilized, as previously described (Bergmaier et al. 2002b). A sterile yeast extract
(Rosell Institute Inc., Montreal, PQ, Canada) solution (400 g/l) was added to give a final
concentration in the SWP between 0 and 1.37 % (w/v).
After a colonization and equilibration period (8 days), continuous culture with Lb. rhamnosus
RW-9595M was conducted with pH controlled at 6 (Bergmaier et al. 2002b). The set points for
yeast extract concentration (CYE, 0-1.37 % w/v), temperature (T, 24-44°C) and dilution rate (D,
0.8-2.8 h-1) were changed every 24 h according to a central composite experimental design. The
values for D in this study are calculated with respect to the total fermentation volume of the ICB
(0.7 l). Samples of the effluent of the two bioreactors were taken for each tested condition, after a
20-h stabilization period following the condition change, and used for cell enumeration, sugar,
and lactic acid determinations. A sample of about 15 colonized carriers was also taken and kept
frozen at -80°C for determination of immobilized biomass as described previously (Bergmaier et
al. 2002b). After day 10, the formation of large aggregates was observed. After this time,
additional samples of the homogenous culture broth, including floating aggregates were taken
from both bioreactors and from the effluent of the FCB for aggregate analysis and concentration
measurement.
5.4.2 Biomass concentration determinations
Free-cell concentration in the broth was estimated by viable cell counts (CFU per millilitre) or by
dry weight (g/l) as previously described (Bergmaier et al. 2002b). Reported data are means for
duplicate analysis.
Immobilized cell concentration was determined by measuring the DNA content as previously
described (Bergmaier et al. 2002a), using the method of Wang (1988) with some modifications.
A calibration curve with cell counts, biomass dry weight and DNA content of free cells of
114
Lb. rhamnosus ATCC-9595 was used to correlate these biomass measures. DNA of free and
immobilized cells was extracted with 0.5 N perchloric acid at 70°C for 30 min. The DNA
concentration was determined by the diphenylamine method (Burton 1956). Each analysis was
repeated three times.
For viable biomass content determination, the aggregates were washed with distilled water and
dried on a filter paper. A sample of about 0.1 g (wet weight) of aggregates was accurately
weighed. The cell concentration in the sample was determined by measuring the DNA content in
the aggregate using the diphenylamine method, as described before for cell concentration
determination in the solid supports. Biomass content was expressed in colony forming unit or cell
dry weight per aggregate dry weight (CFU/g or g/g, respectively). Reported data are means for
duplicate analysis.
5.4.3 Microscopy observations
Preparations of cells in the fermented broth were stained with methylene blue and observed using
a Leitz Weltzlar microscope. Samples of colonized support and aggregates were fixed and
ethanol dehydrated as described previously (Bergmaier et al. 2002b). They were embedded in
epon, semi-fine sectioned (about 100 µm) and post-stained with methylene blue for optical
microscopy examination. For scanning electronic microscopy, samples were dried in a critical
point drier, mounted onto copper stubs and coated with gold (~ 300 Å) in a sputter coater. These
stubs were scanned at different angles under scanning electron microscope (Jeol JSM35; Jeol,
Tokyo, Japan) at 15 kV.
5.4.4 Aggregate dry weight determination
For determination of the dry weight of aggregates in the broth, a homogeneous sample of 10 ml
of fermented broth was taken. The aggregates were allowed to sediment and the supernatant was
discarded. The aggregates were washed twice with 10 ml distilled water and then transferred to a
preweighed aluminium dish. They were dried to a constant weight in a vacuum oven at 70°C.
Reported data are means for duplicate analyses.
115
5.4.5 Chemical analysis of aggregates
For chemical characterization, about 2-g wet weight of aggregates were thoroughly washed three
times with 8 ml 80% ethanol in order to eliminate low molecular weight sugars, and centrifuged
(5,000g, 10 min, 4ºC). The aggregates in aluminium weighing dishes were dried in a vacuum
oven until constant weight (4 h, 60ºC).
For polysaccharide quantification, a sample of about 0.02 g of dried aggregates was accurately
weighed and crushed. Ten ml H2SO4 0.1 M was added to 0.01 g aggregate sample and
homogenized with an Ultraturrax (IKA Labortechnik, Germany; 13500 rpm, 30s). This solution
was heated in closed tubes (60ºC, 3 h) and centrifuged (8,000g, 10 min, 20ºC). Total sugars in the
supernatant were quantified by the phenol-sulfuric acid method (Dubois et al. 1956) with glucose
as standard. The analysis was repeated two times.
For total nitrogen determination, about 0.08 g of dried aggregates were analysed with a
protein/nitrogen analyser (LECO FP-528, LECO, St Joseph, MI, USA). A standard of EDTA
(LECO, 9.56% nitrogen) was used. The total nitrogen content of aggregates was expressed as
percentage of dry weight. Analysis was repeated two times.
Samples for the measurement of phosphorus, potassium, calcium, magnesium and sodium ions
were digested using the method of Isaac and Johnson (1976). About 0.1 g of sample were mixed
with 2 ml of a mineralization solution (97 g H2SeO3, 100 ml H2O, 4 l H2SO4) and 2 ml H2O2, and
incubated at 400°C for 20 min. After cooling, 4 ml water and 1 ml of a lanthanum solution (5%)
were added and the volume was completed to 100 ml with water. Phosphorus determination was
carried out with the method of Tandon et al. (1968). For determination of potassium, calcium,
magnesium and sodium ions, the solution was directly analyzed by atomic absorption
spectroscopy.
5.4.6 Experimental design and statistic analysis
The set points for CYE, T and D during the 32-day culture were changed every 24 h according to a
central composite rotatable design, as described previously (Bergmaier et al. 2002b). The effects
of these three factors and their interactions on the fermentation were analyzed with response
surface analysis. Two covariates were used in the analysis. The covariate age accounted for the
116
age of the fermentation and corrected for time evolution of the system. The second covariate stop
accounted for an interruption of the fermentation due to pumping problems and a change in ICB-
outlet geometry. These problems occurred as a result of the massive formation of aggregates after
12 days. This second covariate is equal to zero or one, before or after interruption, respectively.
The dependent variables tested in this work were the aggregate dry weights in the ICB and FCB.
5.5 Results
Continuous culture with Lb. rhamnosus RW-9595M for EPS production was carried out in a two-
stage fermentation system. Cells were immobilized on solid porous supports (ImmobaSil®) in the
first reactor (ICB) and the second reactor (FCB) was continuously inoculated with cells released
from the first ICB. A 32-day chemostat culture was conducted in a whey-permeate-based
medium with fermentation conditions changing every 24 h, according to the rotatable central
composite experimental design.
5.5.1 Microscopical and macroscopical observations
Immediately after colonization and equilibration of the fermentation system, a morphology
change in the culture was observed by optical microscopy. Particularly in the culture broth in the
second FCB bioreactor, the normally short chains of lactobacilli of up to 4 cells began to grow
and to form a network-like structure (Bergmaier et al. 2002b) (Chapitre 4). The colonization of
the supports was observed by scanning electronic microscopy. Observation of the pores near the
carrier surface (Fig. 5.1a) confirmed the morphological change of the culture, previously detected
by optical microscopy observation of released free cells. Very long chains were also seen in the
inner pores of the support (Fig. 5.1b), with dense cell packing and the presence of EPS on the cell
surfaces and cross-linking the cells (Fig. 5.1c).
At day 3 of the fermentation, small aggregates were clearly visible in the first reactor. Aggregates
progressively clogged the middle-hole of the Raschig-Ring formed supports at day 8, and were
released in the medium and obstructed the screen (0.5 mm mesh) of the first fermenter outlet used
to retain the supports. The fermentation was stopped and the outlet was replaced by a tapered
stainless steel tube which retained supports but not the aggregates. The fermentation was
restarted with central point settings and equilibrated for one day before continuing with the
117
experimental design. Subsequently, the aggregates were always present in both bioreactors.
Samples of aggregates were analyzed by optical microscopy. Semi-fine slices (Fig. 5.2a and b),
stained with methylene blue, showed the very high cell densities and the formation of channels
between the surfaces and the inner parts of the aggregates. This organisation of the microbial
community may facilitate the exchange of nutrients and products with the surrounding liquid
medium. Scanning electronic microscopy photographs of aggregates showed lactobacilli
entrapped in a network-like structure (Fig. 5.3a). Crystal-like structures entrapped in the
aggregates were observed as well (Fig. 5.3b).
118
a)
b)
c)
Fig.
5.1
Sca
nnin
g el
ectro
n m
icro
scop
y of
col
oniz
ed Im
mob
aSil®
sup
ports
: a) p
ore
at th
e su
rfac
e (m
agni
ficat
ion
1600
X, b
) and
c) i
nner
pore
s (m
agni
ficat
ion
3600
X a
nd 1
2000
X, r
espe
ctiv
ely)
.
a)
b)
c)
Fig.
5.2
Opt
ical
mic
rosc
opy
obse
rvat
ions
of s
emi-f
ine
slic
es o
f agg
rega
tes s
tain
ed w
ith m
ethy
lene
blu
e: a
) hig
h ce
ll de
nsity
(20
X),
b) a
nd
c) fo
rmat
ion
of c
hann
els (
63 X
).
a) b)
Fig. 5.3 Scanning electron microscopy of a cut through the aggregate: a) at a magnification
of 11000 X, b) at a magnification of 7800 X with crystal.
5.5.2 Aggregate production
The aggregate production in both reactors was measured by the dry weight of washed
aggregates in the fermented medium (Fig. 5.4). The quantity of aggregates in the
bioreactors was apparently affected by the fermentation conditions which were changed
every 24 h according to the central composite design. Aggregate quantity increased with
time during the continuous fermentation with different patterns in the ICB and FCB.
During the first 11 days, aggregate concentration progressively increased in the FCB from 5
to 12.1 g/l. On day 12 corresponding to the day after fermentation interruption, a sharp
increase in aggregate concentration to 33.3 g/l was observed followed by a stable period
between day 12 and 18 (28.6 ± 2.2 g/l). Finally, for the last 5 days, a very high
concentration averaging 54.8 ±13.2 g/l, was determined. In the ICB aggregate
concentration was much lower than in the FCB, with a low concentration (2.5 ± 1.5 g/l)
until day 19. Between day 19 and 20, a large increase from 2.5 to 35.9 g/l was observed,
followed by a stable aggregate concentration of 33.8 ± 7.6 g/l. The maximum aggregate dry
weight in the ICB and FCB was measured at day 22, with 42.1 and 73.9 g/l, respectively.
Response surface analysis of dry weight did not reveal any statistically significant model at
a 90% confidence interval for the independent variable CYE, T, and D.
120
To estimate the productivity of the fermentation system for aggregate production, the
aggregate dry weight in the effluent of the two-stage fermentation system was also
determined (Fig. 5.5). Aggregate dry weight in the fermented broth varied between 3.16
and 28.59 g/l. Mean aggregate production before day 12 (18.33 ± 4.79 g/l) was higher than
after day 12 (8.21 ± 3.18 g/l). The aggregate volumetric productivity of the two-stage
fermentation system ranged between 5.68 and 49.54 g/l h (Fig. 5.5). As for aggregate
accumulation in the two bioreactors, no statistically significant model (p<0.1) was found
for this parameter as a function of the experimental factors yeast extract concentration,
temperature and dilution rate. However as for aggregate production, volumetric
productivity was higher before day 12 (31.58 ± 10.04 g/l) than after (14.15 ± 4.60 g/l).
5.5.3 Aggregate composition
Samples of aggregates, taken after day 12, were analysed for biomass, nitrogen and
polysaccharide contents. The viable biomass in the aggregates was determined by
extraction and quantification of microbial DNA. There was no statistically significant
(p<0.1) time evolution of biomass content in the aggregates, with extremely high values
varying between 3.27·1012 and 6.52·1012 CFU/g and a mean of
4.32·1012 ± 0.97·1012 CFU/(g aggregate dry weight). Using the biomass calibration curve of
the DNA method, an aggregate biomass content of 1.88 ± 0.42 g/g dry weight was
calculated. The mean total nitrogen and polysaccharide contents were 10.12 ± 0.1 % and
14.2 ± 1.6 % (w/w), respectively.
Aggregate samples of day 11 and 13 were also analyzed for their content in phosphorus and
other minerals. Phosphorus, potassium, calcium, magnesium and sodium content were
2.01 ± 0.35, 0.91 ± 0.51, 0.12 ± 0.20, 0.07 ± 0.06, 0.47 ± 0.34 g/100 g aggregate dry
weight, respectively.
121
0
10
20
30
40
50
60
70
80
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24Age (d)
Agg
rega
te D
ry W
eigh
t (g/
L)
Fig. 5.4 Change of aggregate dry weight in the fermented broth in the first ICB (solid bars) and the second FCB (dashed bars) bioreactors as a measure of aggregate accumulation during the 32-day continuous culture. Age 1 day corresponds to the start of the experimental design after an 8-day initial stabilization period. Fermentation conditions were changed every day according to the central composite rotatable design.
0
10
20
30
40
50
60
70
1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Age (d)
Agg
rega
te D
ry W
eigh
t (g/
L) /
Volu
met
ric P
rodu
ctiv
ity (g
/Lh)
Fig. 5.5 Change of aggregate dry weight in effluent samples (solid bars) and volumetric productivity of the two-stage continuous culture (dashed bars) during the 32-day experiment. Age 1 day corresponds to the start of the experimental design after an 8-day initial stabilization period. Fermentation conditions were changed every day according to the central composite rotatable design.
122
5.6 Discussion
Lb. rhamnosus RW-9595M was immobilized on solid porous supports and a continuous 32-
day culture was carried out in a two-stage fermentation system. In a previous paper
(Bergmaier et al. 2002b) (Chapitre 4), the influence of yeast extract concentration,
temperature and dilution rate on biomass, EPS and lactic acid productions in both reactors
and on immobilized biomass was reported. Despite the very high immobilized and free-cell
biomass in both bioreactors and the high metabolic activity of the culture, shown by high
lactic acid production, very low amounts of soluble EPS were produced in the fermented
broth, averaging 108 ± 90 and 30 ± 142 mg/l for the ICB and FCB, respectively. This low
production was mainly attributed to a physiological change of the culture due to
immobilization. A morphological change was also observed with increased cell-chain
length and formation of large (1-2 mm) cell-containing aggregates.
After only 3 days of culture, a morphological change of the culture was observed with
optical microscopy (Bergmaier et al. 2002b). The rod shaped cells transformed into thin
long cells and the chain length was elongated. Similar observations were made by
Senthuran et al. (1997), who described elongated cells with branched structures during
repeated batch fermentation with immobilized Lb. casei subsp. rhamnosus. Norton et al.
(1993) and Gonçalves et al. (1992) reported similar morphological changes for
Lb. helveticus immobilized in gel beads and Lb. rhamnosus immobilized on solid supports,
respectively, during continuous lactic acid fermentation. On the contrary, Lb. plantarum
cells immobilized on chitosan-treated polypropylene matrix underwent a change from rod
to coccoid shape during repeated batch lactic acid fermentation as observed by scanning
electronic microscopy.
In this study, the morphological change of immobilized Lb. rhamnosus RW-9595M was
characterized by scanning electronic microscopy (SEM) of the porous support. Cells at the
surface (Fig. 5.1a) and in the inner pores of the carrier (Fig. 5.1b) were elongated. In the
inner regions of the support (Fig. 5.1c), shorter cells and the production of extracellular
123
substances were observed. Similar observations with SEM also showed cell length
elongation for Zymomonas mobilis cells immobilized on Al2O3 granules (Bekers et al.
2001).
After 10 days of culture, the morphological change resulted in the formation of aggregates
in the two bioreactors that were clearly visible and progressively grew in size to
macroscopic grains of 1-2 mm. These aggregates were fixed, embedded in epon, semi-fine
sectioned (about 100 µm) and stained with methylene blue before observation with optic
microscopy (Fig. 5.2a and b). A cellular organization of the microbial community
facilitating the exchange of nutrients and metabolic products with the surrounding bulk
liquid, with a network-like channel system, was visually observed. Using scanning confocal
laser microscopy, Lawrence et al. (1991) were able to inspect three-dimensional biofilms of
P. aeruginosa, Pseudomonas fluorescens and Vibrio parahaemolyticus. All biofilms were
highly hydrated with open structures including water channels and exopolysaccharides. As
in the present study, the high porosity and channels in Pseudomonas and Vibro biofilms
allowed the free diffusion of low-molecular-weight compounds such as nutrients and
metabolic products. Observation of the aggregates with SEM showed their heterogeneity.
In some cases bacterial cells were embedded in a network-like structure (Fig. 5.3a). In other
regions the cell density was very high and EPS production was observed (Fig. 5.3b) as for
the presence of crystal bodies, entrapped in the aggregate (Fig. 5.3b).
The quantity of aggregates was measured by determining the dry weight of washed
aggregates in the fermented broth. The aggregate concentration in the two bioreactors
largely changed with culture conditions and increased with time during the continuous
fermentation (Fig. 5.4). A large increase of the aggregate concentration in the FCB from
12.1 to 33.3 g/l at day 12 coincided with a change in ICB reactor outlet geometry.
Afterwards, the aggregates formed in the ICB were less retained and were pumped with the
medium in the FCB where they continued to grow and were retained by the collecting tube
geometry (with a diameter of about 2.5 mm). Before day 12 the mean aggregate
concentration in the FCB was low, equal to 6.9 g/l and it reached a very high value of
124
54.8 g/l during the last 5 days of fermentation. An important increase in aggregate
concentration was also observed in the ICB at day 20 from 2.5 ± 1.5 g/l to 33.8 ± 7.6 g/l for
the periods before and after that time. This change could be explained by the specific
fermentation conditions applied on day 20 (CYE = 1.1, T = 28°C, D = 1.2 h-1) and by the
progressive growth of the aggregates with time in the ICB which reached a critical size for
the tube geometry. The aggregate concentrations for the final period of the fermentation in
both bioreactors were very high.
Accumulation of aggregates in the FCB progressively increased with time (Fig. 5.4). This
data could be explained by the retention of large aggregates that could not flow through the
outlet tubing of the FCB. These aggregates in the FCB effluent could be easily harvested by
simply sieving the effluent on a screen (0.5 mm mesh size). To estimate the productivity of
the fermentation system for aggregate production the aggregate dry weight in the effluent
of the fermentation system was determined (Fig. 5.5). Aggregate dry weight in the effluent
varied between 3.16 and 28.59 g/l depending on time and culture conditions and
corresponded to an aggregate volumetric productivity of the two stage-fermentation system
varying between 5.68 and 49.54 g/l h. The second order model of the central composite
design (Bergmaier et al. 2002b) could not fit (p<0.1) the variation of aggregate production
and productivity data. This result could be explained by the complex effects of many
factors, including the independent variables (CYE, T and D), culture time, aggregate size
and geometry of the reactors on aggregate production and retention in both reactors.
From day 12 on, samples of aggregates were analysed for biomass, nitrogen and
polysaccharide contents. The biomass in the aggregates was determined by extraction and
quantification of microbial DNA, with a method similar to that used for immobilized
biomass quantification in solid supports described in the previous paper (Bergmaier et al.
2002b). With Lb. rhamnosus RW-9595M, a very rapid degradation of DNA occurs with
cell death as a result of a very active DNA-degrading enzyme (Peant and LaPointe 2001).
The immobilized cell content measured with this method can consequently mainly be
attributed to living cells, in which DNA is not degraded. A very high viable biomass
125
content in aggregates of 4.32·1012 ± 0.97·1012 CFU/g dry weight and 1.88 ± 0.42 g/g was
calculated from calibration curves of the method determined with viable cell counts or
biomass measurements (Bergmaier et al. 2002a). This biomass value largely exceeding
100% of aggregate dry weight shows the approximative nature of the DNA-method for
immobilized biomass quantification. The DNA method is based on the assumptions that the
DNA contents of immobilized cells of Lb. rhamnosus RW-9595M and free cells of
Lb. rhamnosus ATCC-9595 are the same. However, immobilized cells showed very large
physiological and morphological changes when compared with planktonic cells. In
particular, immobilized cells were much smaller than planktonic cells resulting in higher
ratio extracted DNA per unit biomass, resulting in an overestimation of immobilized
biomass by this method. Nevertheless, our data clearly indicated the extremely high viable
cell content of aggregates.
The total nitrogen content of aggregates was 10.12 ± 0.1 % (w/w) expressed in dry weight.
With a typical composition of 13.7% (w/w) nitrogen in bacterial cell composition (van
Dijken and Harder 1975), this data translates to a total biomass content in aggregates of
approximately 74% (w/w). Also the phosphorus content of aggregates was high, with an
average of 2.01 % (w/w). Battley (1991) determined the elemental composition of
Escherichia coli K-12 and found a ratio between nitrogen and phosphorus of 5.25:1 which
is in agreement with the ratio in aggregates in our study (5.03:1), supporting the total
biomass calculation from the nitrogen content and the high viable biomass found with the
DNA extraction method.
Further chemical analysis of the aggregates showed a high polysaccharide content, equal to
14.2 ± 1.6 % (w/w). The polysaccharide content of typical bacteria is only about 5 %
(Atkinson and Mavituna 1991). Our data indicate that a high concentration of EPS is
accumulated in the aggregates and contributed to the formation of the network-like
structure entrapping cells, as observed by SEM (Fig. 5.3a). Atomic absorption spectroscopy
quantified relatively low concentrations of K+, Ca++, Mg++ and Na+, and gave no further
indication on the nature of the crystal substance observed by SEM in aggregates (Fig. 5.3b).
126
In this study, it was shown that the aggregates produced during continuous culture with
Lb. rhamnosus RW-9595M were mainly composed of viable biomass of this potentially
probiotic strain and its exopolysaccharide. Exopolysaccharides, especially from probiotic
bacteria, are potential prebiotics and, furthermore, may contribute to human health due to
their anti-tumour, anti-ulcer, immunomodulating and cholesterol-lowering activities (Ruas-
Madiedo et al. 2002a). The aggregates produced in this study, combining probiotic bacteria
and prebiotic polysaccharides, comply with the concept of synbiotics proposed by Gibson
and Roberfroid (1995). Furthermore, immobilization allowed to change cell physiology and
could improve the resistance of cells to physico-chemical stresses such as during freeze-
drying or transit of the gastro-intestinal tract (Doleyres et al. 2002a). The aggregates
produced in supplemented whey permeate medium could thus find application as synbiotic
food-ingredients for dairy and non-dairy products. A further potential application of the
technology presented in this paper is a continuous process for the production of
concentrated starters, without the use of centrifugation or filtration for cell concentration.
Furthermore, the particulate state of the biomass could enable the use of fluid bed drying,
as done with bakers yeast, in substitution to freeze-drying.
5.7 Conclusions
An extensive aggregation of Lb. rhamnosus RW-9595M was observed during a chemostat
culture with immobilized cells in a two-stage fermentation system. The aggregates grew in
size with time and reached a macroscopic size of 1 to 2 mm after about 14-day culture.
They showed a cellular organization facilitating nutrient and metabolic product exchange
with the bulk liquid. The aggregate concentration in the two bioreactors and the aggregate
volumetric productivity of the system (up to 49.54 g/l h) was extremely high. The viable
biomass content of aggregates estimated by a DNA extraction method was also very high
(4.32·1012 ± 0.97·1012 CFU/g). Aggregates were mainly composed of biomass and non-
soluble EPS (73.8% and 14.2% (w/w) on dry weight, respectively). The aggregates can be
easily separated from the medium and could be used as a synbiotic product with very high
active cell and EPS concentrations.
Conclusion générale L’objectif général de ce travail a été de développer et d’optimiser une technologie de
production d'exopolysaccharides (EPS), basée sur la fermentation, avec des cellules
immobilisées, d’un milieu à base de perméat de lactosérum. Pour arriver à cette fin, la
souche Lb. rhamnosus RW-9595M a été choisie comme souche de travail à cause de sa
forte production en EPS.
Dans un premier temps, une nouvelle méthode de dosage de biomasse a été mise au point.
Cette nouvelle méthode se base sur la séparation des EPS et des sucres simples dans le
milieu fermenté par l'ultrafiltration (UF). Elle permet un suivi précis de la production d'EPS
par des bactéries lactiques pendant des fermentations. Comparée à une méthode
conventionnelle impliquant une précipitation des macromolécules à l'aide d'un solvant
organique, une précipitation des protéines avec le TCA, une purification par la dialyse et
une lyophilisation, la quantification par la méthode UF prend beaucoup moins de temps
(8 h comparé à environ 10 jours). En outre, cette méthode est simple et exige des volumes
d'échantillon aussi bas que 1 à 5 ml, ce qui permet la réalisation d'un plus grand nombre
d'analyses et de répétitions des points pendant les fermentations.
Dans un deuxième temps, la production d'EPS a été suivie lors de fermentations en batch,
avec des cellules planctoniques et comparée avec la production d'EPS lors de fermentations
en batch répété avec des cellules immobilisées sur des supports poreux solides en
caoutchouc de silicone, ImmobaSil®. Une méthode de dosage de la biomasse immobilisée a
été développée, afin de pouvoir suivre son évolution durant les fermentations. Cette
méthode s'est basée sur l'extraction et la quantification de l'ADN microbien et n'est pas
troublée par la présence du support solide, contrairement à des méthodes traditionnelles
comme l'énumération sur plaque ou le poids sec. Les cultures en batch répété ont
clairement montré le potentiel de la technologie des cellules immobilisées sur des supports
solides pour la production d'EPS, augmentant la productivité volumétrique maximale de
110 à 258 mg/l h, comparées aux cultures avec des cellules planctoniques. En outre, cette
technologie résulte en des périodes plus courtes d'arrêt du système de fermentation,
128
permettant plus de trois cultures en batch par jour, et une réutilisation des cellules
microbiennes, ce qui augmente encore plus la productivité industrielle.
Lors de fermentations en continu avec des cellules planctoniques, une production maximale
élevée d'EPS égale à 1800 mg/l a été obtenue pour un taux de dilution (D) de 0.3 h-1. Une
productivité volumétrique maximale de 542.6 mg/l · h a été obtenue pour un D de 0.7 h-1.
C'est la productivité d'EPS des LAB la plus élevée en littérature. Les cellules ont été
immobilisées par adsorption sur ImmobaSil® et ont été employées pendant une culture en
continu à long terme. Cette culture a été réalisée dans un système de fermentation à deux
étages, le premier étage contenant les cellules immobilisées. En dépit de valeurs très
élevées pour la biomasse immobilisée et planctonique dans ce système et une activité
métabolique élevée, montrée par les données de production d'acide lactique, la production
d'EPS soluble a été très faible. Cette faible production a pu principalement être attribuée à
un changement physiologique de la culture due à l'immobilisation. Des cultures successives
en batch, inoculées avec des cellules du système en continu, ont prouvé la réversibilité de
ce changement physiologique. Un changement morphologique important de la culture a
également été observé. Les chaînes normalement courtes des lactobacilles ont accrues et
ont formé un réseau. De plus, la formation d'agrégats après 10 jours de culture a été
observée.
Avec le temps de fermentation, les agrégats se sont développés en taille et ont atteint une
taille macroscopique de 1 à 2 millimètres après environ 14 jours. Leur examen
microscopique a démontré une organisation cellulaire facilitant l'échange des nutriments et
des métabolites avec le milieu environnant. La concentration d'agrégats dans les deux
bioréacteurs et la productivité volumétrique d'agrégats du système (jusqu'à 49,54 g/l h)
étaient extrêmement élevées. La teneur en biomasse viable des agrégats, estimée par la
méthode d'extraction d'ADN, était également très élevée (4.32·1012 ± 0.97·1012 CFU/g). Les
agrégats se sont principalement composés de biomasse et d'EPS non-soluble
(respectivement 73.8% et 14.2% (w/w) du poids sec). Ils peuvent être facilement séparés du
129
milieu et pourraient être employés comme produit synbiotique, avec un contenu en cellules
actives et en EPS très élevé.
Dans ce travail, une approche prometteuse pour l'usage du perméat de lactosérum, un sous-
produit de l'industrie laitière disponible en grande quantité et avec une valorisation limitée
est proposée. Les EPS, produits dans des quantités appréciables, pourraient trouver leur
place comme bioingrédient dans des aliments nutraceutiques dont le marché est en forte
croissance. La rentabilité de la production d'EPS pourrait encore être haussée en optimisant
les conditions de culture des fermentations avec des cellules immobilisées.
Ce travail a mis en évidence des changements physiologiques et morphologiques majeurs
des bactéries lactiques lors des fermentations en continu avec des cellules immobilisées. Un
tel phénomène a aussi été observé par d'autres chercheurs de notre équipe de laboratoire.
Ceci a mené au dépôt d'une demande d'un brevet provisoire. Néanmoins, d'autres cultures
avec des cellules immobilisées doivent encore être réalisées et les cellules doivent être
caractérisées afin de mieux comprendre ce phénomène.
Bibliographie Arnaud J.-P., Lacroix C., Choplin L. (1992) Effect of agitation rate on cell release rate and
metabolism during continuous fermentation with entrapped growing Lactobacillus
casei subsp. casei. Biotechnol Tech 6: 265-270.
Atkinson B., Mavituna F. (1991) Biochemical engineering and biotechnology handbook.
Stockton Press, New York, USA.
Austin G.D., Watson R.W.J., D'Amore T. (1994) Studies of on-line viable yeast biomass
with a capacitance biomass monitor. Biotechnol Bioeng 43: 337-341.
Barbotin J.N., Nava Saucedo J.E., Thomasset B. 1989. Morphological observations on
immobilized cells. dans J.A.M. De Bont , J. Visser, B. Mattiasson, et J. Tramper,
eds. Physiology of immobilized cells. Elservier Science Publishers, Amsterdam, The
Netherlands.
Battley E.H. (1991) Calculation of the heat of growth of Escheria coli K-12 on succinic
acid. Biotechnol Bioeng 37: 334-443.
Becker A., Katzen F., Puhler A., Ielpi L. (1998) Xanthan gum biosynthesis and application:
A biochemical/genetic perspective. Appl Microbiol Biotechnol 50: 145-152.
Bekers M., Laukevics J., Karsakevich A., Ventina E., Kaminska E., Upite D., Vina I.,
Linde R., Scherbaka R. (2001) Levan-ethanol biosynthesis using Zymomonas
mobilis cells immobilized by attachment and entrappment. Process Biochem 36:
979-986.
Bergmaier D., Lacroix C. (2002) Aggregate formation during chemostat culture with
Lactobacillus rhamnosus RW-9595M. Biotechnol Prog soumis pour publication.
Bergmaier D., Lacroix C., Champagne C.P. (2002a) Exopolysaccharide production during
batch cultures with free and immobilized Lactobacillus rhamnosus RW-9595M. J
Biotechnol soumis pour publication.
Bergmaier D., Lacroix C., Champagne C.P. (2002b) Exopolysaccharide production during
chemostat cultures with free and immobilized Lactobacillus rhamnosus RW-
9595M. Biotechnol Prog soumis pour publication.
131Bergmaier D., Lacroix C., Macedo M.G., Champagne C.P. (2001) New method for
exopolysaccharide determination in culture broth using stirred ultrafiltration cells.
Appl Microbiol Biotechnol 57: 401-406.
Bertrand N., Fliss I., Lacroix C. (2001) High nisin-Z production during repeated-cycle
batch cultures in supplemented whey permeate using immobilized Lactococcus
lactis UL719. Int Dairy J 11: 953-960.
Boels I.C., van Kranenburg R., Hugenholtz J., Kleerebezem M., de Vos W.M. (2001) Sugar
catabolism and its impact on the biosynthesis and engineering of exopolysaccharide
production in lactic acid bacteria. Int Dairy J 11: 723-732.
Bouzar F., Cerning J., Desmazeaud M. (1996) Exopolysaccaride production in milk by
Lactobacillus delbrueckii ssp. bulgaricus CNRZ 1187 and by two colonial variants.
J Dairy Sci 79: 205-211.
Bouzar F., Cerning J., Desmazeaud M. (1997) Exopolysaccharide production and texture-
promoting abilities of mixed-strain starter cultures in yoghurt production. J Dairy
Sci 80: 2310-2317.
Bryers J.D. (1993) The biotechnology of interfaces. J Appl Bacteriol Symposium
Supplement 74: 98S-109S.
Buchtmann C., Kies U., Deckwer W.-D., Hecht V. (1997) Performance of three phase
fluidized bed reactor for quinoline degradation on various supports at steady state
and dynamic conditions. Biotechnol Bioeng 56: 295-303.
Burton K. (1956) A study of the conditions and mechanism of the diphenylamine reaction
for the colorimetric estimation of deoxyribonucleic acid. Biochem J. 62: 315-323.
Cachon R., Antérieux P., Diviès C. (1998) The comparative behaviour of Lactococcus
lactis in free and immobilized culture processes. J Biotechnol 63: 211-218.
Cachon R., Molin P., Divies C. (1995) Modeling of continuous pH-stat stirred tank reactor
with Lactococcus lactis ssp. lactis bv. diacetylactis immobilized in calcium alginate
gel beads. Biotechnol Bioeng 47: 567-574.
Cerning J. (1990) Exocellular polysaccaride produced by lactic acid bacteria. Microbiol
Rev 87: 113-130.
132Cerning J. 1994. Polysaccharides exocellulaires produits par les bactéries lactiques.
Pages 309-329 dans I.H. Roissart, Luquet, F.M., ed. Bactéries Lactiques, Grenoble,
France.
Cerning J., Bouillanne C., Desmazeaud M.J. (1986) Isolation and characterization of
exocellular polysaccharide produced by Lactobacillus bulgaricus. Biotechnol Lett
8: 625-628.
Cerning J., Bouillanne C., Desmazeaud M.J. (1988) Exocellular polysaccharide production
by Streptococcus thermophilus. Biotechnol Lett 10: 255-260.
Cerning J., Bouillanne M., Landon M., Desmazeaud M.J. (1990) Comparison of exocellular
polysaccharide production by thermophilic lactic acid bacteria. Sci Aliments 10:
443-451.
Cerning J., Bouillanne M., Landon M., Desmazeaud M.J. (1992) Isolation and
characterization of exopolysaccharides from slime-forming mesophilic lactic acid
bacteria. J Dairy Sci 75: 692-699.
Cerning J., Renard C.M.G.C., Thibault J.F., Bouillanne C., Landon M., Desmazeaud M.,
Topisirovic L. (1994) Carbon source requirements for exopolysaccharide production
by Lactobacillus casei CG11 and partial structure analysis of the polymer. Appl
Environ Microbiol 60: 3914-3919.
Chabot S., Yu H.L., De Leseleuc L., Cloutier D., Van Calsteren M.R., Lessard M., Roy D.,
Lacroix M., Oth D. (2001) Exopolysaccharides from Lactobacillus rhamnosus RW-
9595M stimulate TNF, IL-6 and IL-12 in human and mouse cultured
immunocompetent cells, and IFN-gamma mouse splenocytes. Lait 81: 683-687.
Champagne C.P., Girard F., Rodrigue N. (1993) Production of concentrated suspensions of
thermophilic lactic acid bacteria in calcium alginate beads. Int Dairy J 3: 257-275.
Champagne C.P., Lacroix C., Sodini-Gallot I. (1994) Immobilized cell technologies for the
dairy industry. Crit Rev Biotechnol 14: 109-134.
Chapelle E.W., Picciolo G.L., Deming J.W. (1987) Determination of bacterial content in
fluids. Methods Enzymol 57: 65-72.
Chen K.-C., Lee S.-C., Chin S.-C., Houng J.-Y. (1998) Simultaneous carbon-nitrogen
removal in wastewater using phosphorylated PVA-immobilized microorganisms.
Enzyme Microb Technol 23: 311-320.
133Clark D.S. 1989. Noninvasive techniques in studies of immobilized cells. dans J.A.M.
De Bont , J. Visser, B. Mattiasson, et J. Tramper, eds. Physiology of immobilized
cells. Elservier Science Publishers, Amsterdam, The Netherlands.
De Backer L. 1996. Immobilisation of cells in porous carriers. Pages 373 dans R.G.
Willaert, G.V. Baron, et L. De Backer, eds. Immobilised living cell systems:
Modelling and experimental methods. John Wiley & Sons Ltd., Chichester, UK.
De Vuyst L., De Vin F., Vaningelgem F., Degeest B. (2001) Recent developments in the
biosynthesis and applications of heteropolysaccharides from lactic acid bacteria. Int
Dairy J 11: 687-707.
De Vuyst L., Degeest B. (1999a) Exopolysaccharides from lactic acid bacteria:
Technological bottlenecks and practical solutions. Macromol Symp 140: 31-41.
De Vuyst L., Degeest B. (1999b) Heteropolysaccharides from lactic acid bacteria. FEMS
Microbiol Rev 23: 153-177.
De Vuyst L., Vanderveken F., Van de Ven S., Degeest B. (1998) Production by and
isolation of exopolysaccharides from Streptococcus thermophilus grown in a milk
medium and evidence for their growth- associated biosynthesis. J Appl Microbiol
84: 1059-1068.
Degeest B., de Vuyst L. (1999) Indication that the nitrogen source influences both amount
and size of exopolysaccharides produced by Streptococcus thermophilus LY03 and
modelling of the bacterial growth and exopolysaccharide production in a complex
medium. Appl Environ Microbiol 65: 2863- 2870.
Degeest B., de Vuyst L. (2000) Correlation of activities of the enzymes alpha-
phosphoglucomutase, UDP- galactose 4-epimerase, and UDP-glucose
pyrophosphorylase with exopolysaccharide biosynthesis by Streptococcus
thermophilus LY03. Appl Environ Microbiol 66: 3519-3527.
Degeest B., Vaningelgem F., de Vuyst L. (2001a) Microbial physiology, fermentation
kinetics, and process engineering of heteropolysaccharide production by lactic acid
bacteria. Int Dairy J 11: 747-757.
Degeest B., Vaningelgem F., Laws A.P., De Vuyst L. (2001b) UDP-N-acetylglucosamine
4-epimerase activity indicates the presence of N-acetylgalactosamine in
134exopolysaccharides of Streptococcus thermophilus strains. Appl Environ
Microbiol 67: 3976-3984.
Dell'anno A., Fabiano A., Duineveld G.C.A., Kok A., Danovaro R. (1998) Nucleic acid
(DNA,RNA) quantification and RNA/DNA ratio determination in marine
sediments: Comparison of spectophotometric, fluorometric, and high performance
liquid chromatography methods and estimation of denitrial DNA. Appl Environ
Microbiol 64: 3238-3245.
Doleyres Y., Fliss I., Lacroix C. (2002a) Changes of lactic and probiotic cultures
characteristics during continuous immobilized-cell fermentation with mixed strains.
Appl Environ Microbiol soumis pour publication.
Doleyres Y., Paquin C., LeRoy M., Lacroix C. (2002b) Bifidobacterium longum ATCC
15707 cell production of during free- and immobilized-cell cultures in MRS-whey
permeate medium. Appl Microbiol Biotechnol accepté pour publication.
Duboc P., Mollet B. (2001) Applications of exopolysaccharides in the dairy industry. Int
Dairy J 11: 759-768.
Dubois M., Gilles K.A., Hamilton J.K., Rebers P.A., Smith F. (1956) Colorimetric method
for determination of sugars and related substances. Anal Chem 28: 350-356.
Dudman W.F., ed. 1977. The role of surface polysaccharides in natural environments.
Academic Press, New York, USA.
Dunne W.M., Jr. (2002) Bacterial adhesion: seen any good biofilms lately? Clin Microbiol
Rev 15: 155-166.
Dupont I., Roy D., Lapointe G. (2000) Comparison of exopolysaccharide production by
strains of Lactobacillus rhamnosus and Lactobacillus paracasei grown in
chemically defined medium and milk. J Ind Microbiol Biotechnol 24: 251-255.
Durham D.R., Marshall L.C., Miller J.G., Chmurny A.B. (1994) Characterization of
inorganic biocarriers that moderate system upsets during fixed-film biotreatment
processes. Appl Environ Microbiol 60: 3329-3335.
El-Sayed A.-H.M.M., Mahmoud W.M., Coughlin R.W. (1990) Comparative study of
production of dextransucrase and dextran by cells of Leuconostoc mesenteroides
immobilized on Celite and calcium alginate beads. Biotechnol Bioeng 36: 83-91.
135Fortin C., Vuillemard J. 1989. Effect of immobilization in calcium alginate beads on
regulation of protease production by Myxococcus xanthus cells. dans J.A.M. De
Bont , J. Visser, B. Mattiasson, et J. Tramper, eds. Physiology of immobilized cells.
Elsevier Science Publishers, Amsterdam, The Netherlands.
Freeman A., Blank T., Aharonowitz Y. (1982) Protein determination of cells immobilized
in cross-linked synthetic gels. Eur J Appl Microbiol Biotechnol 14: 13-15.
Gamar L., Blondeau K., Simonet J.-M. (1997) Physiological approach to extracellular
polysaccharide production by Lactobacillus rhamnosus strain C83. J Appl
Microbiol 83: 281-287.
Gamar-Nourani L., Blondeau K., Simonet J.-M. (1998) Influence of culture conditions on
exopolysaccharide production by Lactobacillus rhamnosus strain C83. J Appl
Microbiol 85: 664-672.
Gancel F., Novel G. (1994) Exopolysaccharide production by Streptococcus salivarius ssp.
thermophilus cultures. 1. Conditions of production. J Dairy Sci 77: 685-688.
Garcia-Garibay M., Marshall V.M.E. (1991) Polymer production by Lactobacillus
delbrueckii ssp. bulgaricus. J Appl Bacteriol 70: 325-328.
Gassem M.A., Schmidt K.A., Frank J.F. (1997a) Exopolysaccaride production from whey
lactose by fermentation with Lactobacillus delbrueckii ssp. bulgaricus. J Food Sci
62: 171-174, 207.
Gassem M.A., Sims K.A., Frank J.F. (1997b) Extracellular polysaccaride production by
Lactobacillus delbrueckii ssp. bulgaricus RR in a continuous fermentor. Lebensm
Wiss Technol 30: 273-278.
Gibson G.R., Roberfroid M.B. (1995) Dietary modulation of the human colonic microbiota:
Introducing the concept of prebiotics. J Nutr 124: 1401-1412.
Gikas P., Livingston A.G. (1993) Use of ATP to characterize biomass viability in freely
suspended and immobilized cell bioreactors. Biotechnol Bioeng 42: 1337-1351.
Gikas P., Livingston A.G. (1998) Use of specific ATP concentration and specific oxygen
uptake rate to determine parameters of a structured model of biomass growth.
Enzyme Microb Technol 22: 500-510.
136Gonçalves L.M.D., Barreto M.T.O., Xavier A.M.B.R., Carrondo M.J.T., Klein J. (1992)
Inert supports for lactic acid fermentation - a technological assessment. Appl
Microbiol Biotechnol 38: 305-311.
Grobben G.J., Boels I.C., Sikkema J., Smith M.R., de Bont J.A.M. (2000) Influence of ions
on growth and production of exopolysaccharides by Lactobaccilus delbrueckii
subsp. bulgaricus NCFB 2772. J Dairy Res 67: 131-135.
Grobben G.J., Chin-Joe I., Kitzen V.A., Boels I.C., Boer F., Sikkema J., Smith M.R., de
Bont J.A.M. (1998) Enhancement of exopolysaccharide production by Lactobacillus
delbrueckii subsp. bulgaricus NCFB 2772 with a simplified defined medium. Appl
Environ Microbiol 64: 1333-1337.
Grobben G.J., Sikkema J., Smith M.R., de Bont J.A.M. (1995) Production of extracellular
polysaccharides by Lactobacillus delbrueckii ssp. bulgaricus NCFB 2772 grown in
a chemically defined medium. J Appl Bacteriol 79: 103-107.
Grobben G.J., Smith M.R., Sikkema J., de Bont J.A.M. (1996) Influence of fructose and
glucose on the production of exopolysaccharides and the activities of enzymes
involved in the sugar metabolism and the synthesis of sugar nucleotides in
Lactobacillus delbrueckii subsp. bulgaricus NCFB 2772. Appl Microbiol
Biotechnol 46: 279-284.
Grobben G.J., van Casteren W.H.M., Schols H.A., Oosterfeld A., Sala G., Smith M.R.,
Sikkema J., de Bont J.A.M. (1997) Analysis of the exopolysaccarides produced by
Lactobacillus delbrueckii ssp. bulgaricus NCFB 2772 grown in continuous culture
on glucose and fructose. Appl Microbiol Biotechnol 48: 516-521.
Groboillot A., Boadi D.K., Poncelet D., Neufeld R.J. (1994) Immobilization of cells for
application in the food industry. Crit Rev Biotechnol 14: 75-107.
Harscoat C., Jaffrin M.Y., Bouzerar R., Courtois J. (1999) Influence of fermentation
conditions and microfiltration processes on membrane fouling during recovery of
glucuronane polysaccharides from fermentation broths. Biotechnol Bioeng 65: 500-
511.
Hassan A.N., Frank J.F., Farmer M.A., Schmidt K.A., Shalabi S.I. (1995) Observation of
encapsulated lactic acid bacteria using confocal scanning laser microscopy. J Dairy
Sci 78: 2624-2628.
137Ho K.-L.G., Anthony L., Pometto I., Hinz P.N., Dickson J.S., Demirci A. (1997)
Ingredient selection for plastic composite supports for L-(+)-lactic acid biofilm
fermentation by Lactobacillus casei subsp. rhamnosus. Appl Environ Microbiol 63:
2516-2523.
Holm-Hansen O., Karl D.M. (1987) Biomass and adenylate energy charge determination in
microbial cell extracts and environmental samples. Methods Enzymol 57: 73-85.
Hosono A., Lee J., Ametani A., Natsume M., Hirayama M., Adachi T., Kaminogawa S.
(1997) Characterization of a water-soluble polysaccharide fraction with
immunopotentiating activity from Bifidobacterium adolescentis M101-4. Biosci
Biotech Biochem 61: 312-316.
Hugenholtz J., Looijesteijn E., Starrenburg M., Dijkema C. (2000) Analysis of sugar
metabolism in an EPS producing Lactococcus lactis by 31P NMR. J Biotechnol 77:
17-23.
Isaac R.A., Johnson W.C. (1976) Determination of total nitrogen in plant tissue, using a
block digestor. Journal of the AOAC 59: 98-100.
Iwasaki K.-I., Nakajima M., Sasahara H. (1992) Porous alumina beads for immobilization
of lactic acid bacteria and its application for repeated-batch fermentation in soy
sauce production. J Ferment Bioeng 73: 375-379.
Jolly L., Stingele F. (2001) Molecular organization and functionality of exopolysaccharide
gene clusters in lactic acid bacteria. Int Dairy J 11: 733-745.
Jouenne T., Tresse O., Junter G.A. (1994) Agar-entrapped bacteria as an in vitro model of
biofilms and their susceptibility to antibiotics. FEMS Microbiol Lett 119: 237-242.
Karel S.F., Libicki S.B., Robertson C.R. (1985) The immobilization of whole cells:
Engineering principles. Chem Eng Sci 40: 1321-1354.
Karl D.M. (1980) Cellular nucleotide measurements and applications in microbial ecology.
Microbiol Rev 44: 739-796.
Keweloh H., Heipieper H.J., Rehm H.J. 1989. Phenol tolerance of immobilized bacteria.
dans J.A.M. De Bont , J. Visser, B. Mattiasson, et J. Tramper, eds. Physiology of
immobilized cells. Elservier Science Publishers, Amsterdam, The Netherlands.
Keweloh H., Weyrauch G., Rehm H.J. (1990) Phenol-induced membrane changes in free
and immobilized Escherichia coli. Appl Microbiol Biotechnol 33: 66-71.
138Kimmel S.A., Roberts R.F. (1998) Development of a growth medium suitable for
exopolysaccharide production by Lactobacillus delbrueckii ssp. bulgaricus RR. Int J
Food Microbiol 40: 87-92.
Kimmel S.A., Roberts R.F., Ziegler G.R. (1998) Optimization of exopolysaccharide
production by Lactobacillus delbrueckii ssp. bulgaricus RR grown in a semidefined
medium. Appl Environ Microbiol 64: 659-664.
Kitazawa H., Harata T., Uemura J., Saito T., Kaneko T., Itoh T. (1998) Phosphate group
requirement for mitogenic activation of lymphocytes by an extracellular
phosphopolysaccharide from Lactobacillus delbrueckii ssp. bulgaricus. Int J Food
Microbiol 40: 169-175.
Kitazawa H., Itoh T., Tomioka Y., Mizagaki M., Yamaguchi T. (1996) Induction of IFN-
gamma and IL-1alpha production in macrophages stimulates with
phosphopolysaccharide produced by Lactococcus lactis ssp. cremoris. Int J Food
Microbiol 31: 99-106.
Kitazawa H., Toba T., Itoh T., Kumano N., Adachi S., Yamaguchi T. (1991) Antitumoral
activity of slime-forming encapsulated Lactococcus lactis subsp. cremoris isolated
from Scandinavian ropy sour milk, "viili". Anim Sci Technol 62: 277-283.
Klein J., Vorlop K.-D. 1985. Immobilization techniques-Cells. Pages 203-224 dans M.
Moo-Young, C.L. Cooney, et A.E. Humphrey, eds. Comprehensive biotechnology.
Pergamon Press, Oxford, NY, USA.
Knights A. 1996. Porous silicone rubber as an immobilization matrix for microbial and
mammalian cells: Natural immobilization of a mass transfer limited culture
environment. Pages 162-172 dans R.H. Wijffels, R.M. Buitelaar, C. Bucke, et J.
Tramper, eds. Progress in biotechnology. Elsevier Science Inc., NY, USA.
Knoshaug E.P., Ahlgrent J.A., J.E. T. (2000) Growth associated exopolysaccharide
expression in Lactococcus lactis subspecies cremoris Ropy 352. J Dairy Sci 83:
633-640.
Kojic M., Vujcic M., Banina A., Cocconcelli P., Cerning J., Topisirovic L. (1992) Analysis
of exopolysaccharide production by Lactobacillus casei CG11, isolated from
cheese. Appl Environ Microbiol 58: 4086-4088.
139Kontusaari S., Forsen R. (1988) Finnish fermented milk "Viili" : Involvement of two
cell surface proteins in production of slime by Streptococcus lactis ssp. cremoris. J
Dairy Sci 71: 3197-3202.
Kosseva M., Beschkov V., Kennedy J.F., Lloyd L.L. (1998) Malolactic fermentation in
Chardonnay wine by immobilised Lactobacillus casei cells. Process Biochem 33:
793-797.
Krisch J., Szajani B. (1997) Ethanol and acetic acid tolerance in free and immobilized cells
of Saccharomyces cerevisiae and Acetobacter aceti. Biotechnol Lett 19: 525-528.
Krischke W., Schröder M., Trösch W. (1991) Continuous production of L-lactic acid from
whey permeate by immobilized Lactobacillus casei subsp. casei. Appl Microbiol
Biotechnol 34: 573-578.
Krishnan S., Gowda L.R., Misra M.C., Karanth N.G. (2001) Physiological and
morphological changes in immobilized L. plantarum NCIM 2084 cells during
repeated batch fermentation for production of lactic acid. Food Biotechnol 15: 193-
202.
Lamboley L., Lacroix C., Artignan J.M., Champagne C.P., Vuillemard J.C. (1999) Long-
term mechanical and biological stability of an immobilized cell reactor for
continuous mixed-strain mesophilic lactic starter production in whey permeate.
Biotechnol Prog 15: 646-654.
Lamboley L., Lacroix C., Champagne J.C. (1997) Contiunuous mixed strain mesophilic
lactic starter production in supplemented whey permeate medium using
immobilized cell technology. Biotechnol Bioeng 56: 502-516.
Lamboley L., Lacroix C., Champagne J.C. (2001) Effect of inoculum composition and low
KCl supplementation on the biological and rheological stability of an immobilized-
cell system for mixed mesophilic lactic starter production. Biotechnol Prog 17:
1071-1078.
Lawrence J.R., Korber D.R., Hoyle B.D., Costerton J.W., Caldwell D.E. (1991) Optical
sectioning of microbial biofilms. J Bacteriol 173: 6558-6567.
Laws A.P., Marshall V.M. (2001) The relevance of exopolysaccharides to the rheological
properties in milk fermented with ropy strains of lactic acid bacteria. Int Dairy J 11:
709-721.
140Lemoine J., Chirat F., Wieruszeski J.-M., Strecker G., Favre N., Neeser J.-R. (1997)
Structural characterization of the exocellular polysaccharides produced by
Streptococcus thermophilus SFi39 and SFi12. Appl Environ Microbiol 63: 3512-
3518.
Lo Y.-M., Yang S.-T., Min D.B. (1997) Ultrafiltration of xanthan gum fermentation broth:
Process and economic analyses. J Food Engin 31: 219-236.
Lohmeier-Vogel E.M., Hahn-Hägerdal B., Vogel H.J. (1995) Phosphorous-31 and carbon-
13 nuclear magnetic resonance study of glucose and xylose metabolism in agarose-
immobilized Candida tropicalis. Appl Environ Microbiol 61: 1420-1425.
Lohmeier-Vogel E.M., McIntyre D.D., Vogel H.J. 1989. Nuclear magnetic resonance
spectroscopy as an analytical tool in biotechnology. dans J.A.M. De Bont , J. Visser,
B. Mattiasson, et J. Tramper, eds. Physiology of immobilized cells. Elsevier Science
Publishers, Amsterdam, The Netherlands.
Lohmeier-Vogel E.M., McIntyre D.D., Vogel H.J. (1996) Phosphorous-31 and carbon-13
nuclear magnetic resonance studies of glucose and xylose metabolism in cell
suspensions and agarose-immobilized cultures of Pichia stipitis and Saccharomyces
cerevisiae. Appl Environ Microbiol 62: 2832-2838.
Looijesteijn P., Boels I., Kleerebezem M., Hugenholtz J. (1999) Regulation of
exopolysaccharide production by Lactococcus lactis subsp cremoris by the sugar
source. Appl Environ Microbiol 65: 5003-5008.
Looijesteijn P.J., Hugenholtz J. (1999) Uncoupling of growth and exopolysaccharide
production by Lactococcus lactis subsp. cremoris NIZO B40 and optimization of its
synthesis. J Biosci Bioengin 88: 178-182.
Looijesteijn P.J., Trapet L., de Vries E., Abee T., Hugenholtz J. (2001) Physiological
function of exopolysaccharides produced by Lactococcus lactis. Int J Food
Microbiol 64: 71-80.
Low D., Ahlgren J.A., Horne D., McMahon D.J., Oberg C.J., Broadbent J.R. (1998) Role
of Streptococcus thermophilus MR-1C capsular exopolysaccharide in cheese
moisture retention. Appl Environ Microbiol 64: 2147-2151.
Macedo M.G. (2001) Étude de la production d'exopolysaccharides par Lactobacillus
rhamnosus RW-9595M dans un milieu à base de perméat de lactosérumpages.
141Thèse Ph.D. Faculté des scienes de l'agriculture et de l'alimentation. Université
Laval, Québec, PQ, Canada.
Macedo M.G., Lacroix C., Champagne C.P. (2002a) Combined effects of temperature and
medium composition on exopolysaccharide production by Lactobacillus rhamnosus
RW-9595M in a whey permeate based medium. Biotechnol Prog 18: 167-173.
Macedo M.G., Lacroix C., Gardner N.J., Champagne C.P. (2002b) Effect of medium
supplementation on exopolysaccharide production by Lactobacillus rhamnosus
RW-9595M in whey permeate. Int Dairy J 12: 419-426.
Macedo M.G., Laporte M.-F., Lacroix C. (2002c) Quantification of exopolysaccharide,
lactic acid and lactose concentrations in culture broth by near-infrared spectroscopy.
J Agri Food Chem 50: 1774-1779.
Macura D., Townsley P.M. (1984) Scandinavian ropy milk - identification and
characterization of endogenous ropy lactic streptococci and their extracellular
excretion. J Dairy Sci 67: 735-744.
Marshall V.M., Cowie E.N., Moreton R.S. (1995) Analysis and production of two
exopolysaccharides from Lactococcus lactis subsp. cremoris LC330. J Dairy Res
62: 621-628.
Marshall V.M., Rawson H.L. (1999) Effects of exopolysaccharide-producing strains of
thermophilic lactic acid bacteria on the texture of stirred yoghurt. Int. J. Food
Sci.Technol. 34: 137-143.
Messing R.A., Oppermann R.A. (1979a) Pore dimensions for accumulating biomass. I.
Microbes that reproduce by fission or by budding. Biotechnol Bioeng 21: 49-58.
Messing R.A., Oppermann R.A. (1979b) Pore dimensions for accumulating biomass. II.
Microbes that form spores and exhibit mycelial growth. Biotechnol Bioeng 21: 59-
67.
Mishima K., Mimura A., Takahara Y., Asami K., Hanai T. (1991) On-line monitoring of
cell concentrations by dielectric measurements. J Ferment Bioeng 72: 291-295.
Moreira R.A., Phillips A.J., Humphrey E.A. (1978) Method for determining the
concentration of adsorbed protein and cell biomass in cellulose fermentations.
Biotechnol Bioeng 20: 1501-1505.
142Morishita T., Deguchi Y., Yajima M., Sakurai T., Yura T. (1981) Multiple nutritional
requirements of lactobacilli: Genetic lesions affecting amino acid biosynthetic
pathways. J Bacteriol 148: 64-71.
Mozzi F., de Giori G.S., Oliver G., de Valdez G.F. (1994) Effect of culture pH on the
growth characteristics and polysaccharide production by Lactobacillus casei.
Milchwissen 49: 667-670.
Mozzi F., de Giori G.S., Oliver G., de Valdez G.F. (1996a) Exopolysaccharide production
by Lactobacillus casei in milk under different growth conditions. Milchwissen 51:
670-673.
Mozzi F., de Giori G.S., Oliver G., de Valdez G.F. (1996b) Exopolysaccharide production
by Lactobacillus casei under controlled pH. Biotechnol Lett 10: 435-439.
Mozzi F., Savoy de Giori G.S., Oliver G., Font de Valdez G.F. (1995a) Exopolysaccharide
production by Lactobacillus casei. I. Influence of salts. Milchwissen 50: 186-188.
Mozzi F., Savoy de Giori G.S., Oliver G., Font de Valdez G.F. (1995b) Exopolysaccharide
production by Lactobacillus casei. I. Influence of the carbon source. Milchwissen
50: 307-309.
Mulchandani A., Luong J.H.T. (1989) Biosynthesis of pullulan using immobilized
Aureobasidium pullulans cells. Biotechnol Bioeng 33: 306-312.
Nagaoka M., Hashimoto S., Watanabe T., Yokokura T., Mori Y. (1994) Anti-ulcer effects
of lactic acid bacteria and their cell wall polysaccharides. Biol Pharm Bull 17: 1012-
1017.
Nakajima H., Suzuki Y., Kaizu H., Hirota T. (1992) Cholesterol lowering activity of ropy
fermented milk. J Food Sci 57: 1327-1329.
Nakajima H., Toyoda S., Toba T., Itoh T., Mukai T., Kitazawa H., Adachi S. (1990) A
novel phosphopolysaccharide from slime-forming Lactococcus lactis ssp cremoris
SBT 0495. J Dairy Sci 73: 1472-1477.
Navrátil M., Sturdíc E. (1999) Bioactive components in productions using immobilized
biosystems. Biologia Bratislava 54: 635-648.
Norton S., Lacroix C., Vuillemard J.-C. (1993) Effect of pH on the morphology of
Lactobacillus helveticus in free cell batch and immobilized-cell continuous
fermentation. Food Biotechnol 7: 235-251.
143Norton S., Lacroix C., Vuillemard J.-C. (1994a) Kinetic study of continuous whey
permeate fermentation by immobilized Lactobacillus helveticus for lactic acid
production. Enzyme Microb Technol 16: 457-466.
Norton S., Lacroix C., Vuillemard J.-C. (1994b) Reduction of yeast extract
supplementation in lactic acid fermentation of whey permeate by immobilized cell
technology. J Dairy Sci 77: 2494-2508.
O'Toole G., Kaplan H.B., Kolter R. (2000a) Biofilm formation as microbial development.
Annu Rev Microbiol 54: 49-79.
O'Toole G.A., Gibbs K.A., Hager P.W., Phibbs P.V., Jr., Kolter R. (2000b) The global
carbon metabolism regulator Crc is a component of a signal transduction pathway
required for biofilm development by Pseudomonas aeruginosa. J Bacteriol 182:
425-431.
Oyaas J., Storro I., Levine D.W. (1996) Uptake of lactose and continuous lactic acid
fermentation by entrapped non-growing Lactobacillus helveticus in whey permeate.
Appl Microbiol Biotechnol 46: 240-249.
Parsek M.R., Greenberg E.P. (2000) Acyl-homoserine lactone quorum sensing in gram-
negative bacteria: a signaling mechanism involved in associations with higher
organisms. Proc Natl Acad Sci 97: 8789-8793.
Peant B., LaPointe G. (2001) Mise en evidence d'une nucléase sécrétée et conservée chez le
groupe Lactobacillus casei. Réunion du Club des Bactéries Lactiques. Faculté
d'Oenologie, Université Victor Segalen, Bordeaux, Bordeaux, France.
Perry D.B., McMahom D.J., Oberg C.J. (1998) Manufacture of low fat mozzarella cheese
using exopolysaccharide-producing starter cultures. J Dairy Sci 81: 563-566.
Perry D.B., McMahon D., Oberg C.J. (1997) Effect of exopolysaccharide-producing
cultures on moisture retention in low fat mozzarella cheese. J Dairy Sci 80: 799-
805.
Petry S., Furlan S., Crepeau M.J., Cerning J., Desmazeaud M. (2000) Factors affecting
exocellular polysaccharide production by Lactobacillus delbrueckii subsp.
bulgaricus grown in a chemically defined medium. Appl Environ Microbiol 66:
3427-3431.
144Pham P.L., Dupont I., Roy D., Lapointe G., Cerning J. (2000) Production of
exopolysaccharide by Lactobacillus rhamnosus R and analysis of its enzymatic
degradation during prolonged fermentation. Appl Environ Microbiol 66: 2302-2310.
Pham P.L., Roy D. (2000) Production of exopolysaccharides by Lactobacillus rhamnosus
R: Effect of oxygen tension. Symposium International de Montréal: La santé par les
probiotiques: à la découverte de la microflore intestinale, Montréal, PQ, Canada.
Prenosil J.E., Kut Ö.M., Dunn I.J., Heinzle E. 1995. Immobilized biocatalysts. Ullmann's
enzyclopedia of industrial chemistry. VCH, Weinheim, Germany.
Prigent-Combaret C., Vidal O., Dorel C., Lejeune P. (1999) Abiotic surface sensing and
biofilm-dependent regulation of gene expression in Escherichia coli. J Bacteriol
181: 5993-6002.
Raebel M., Schlierf H. 1980. Ermittlung der aktiven Biomasse im Belebtschlamm durch
Bestimmung der Desoxyribonucleinsäure (DNS). Pages 293-305. Jahrbuch vom
Wasser. Verlag Chemie, Weinheim, Germany.
Ramakrishna S.V., Prakasham R.S. (1999) Microbial fermentations with immobilized cells.
Current Science Bangalore 77: 87-100.
Ramos A., Boels I.C., de Vos W.M., Santos H. (2001) Relationship between glycolysis and
exopolysaccharide biosynthesis in Lactococcus lactis. Appl Environ Microbiol 67:
33-41.
Rashid M.H., Rumbaugh K., Passador L., Davies D.G., Hamood A.N., Iglewski B.H.,
Kornberg A. (2000) Polyphosphate kinase is essential for biofilm development,
quorum sensing, and virulence of Pseudomonas aeruginosa. Proc Natl Acad Sci 97:
9636-9641.
Rawson H.L., Marshall V.M. (1997) Effect of ropy strains of Lactobacillus delbrueckii ssp.
bulgaricus and Streptococcus thermophilus on rheology of stirred yogurt. Int. J.
Food Sci. Technol. 32: 213-220.
Ricciardi A., Clementi F. (2000) Exopolysaccharides from lactic acid bacteria: Structure,
production and technological applications. Ital J Food Sci 12: 22-45.
Robinson D.K., Wang D.I.C. (1987) A novel bioreactor system for biopolymer production.
Ann NY Acad Sci 506: 229-241.
145Ruas-Madiedo P., Hugenholtz J., Zoon P. (2002a) An overview of the functionality of
exopolysaccharides produced by lactic acid bacteria. Int Dairy J 12: 163-171.
Ruas-Madiedo P., Tuinier R., Kanning M., Zoon P. (2002b) Role of exopolysaccharides
produced by Lactococcus lactis subsp. cremoris on the viscosity of fermented milks.
Int Dairy J 12: 689-695.
Ruijssenaars H.J., Stingele F., Hartmans S. (2000) Biodegradability of food-associated
extracellular polysaccharides. Current Microbiology 40: 194-199.
Santos H., Pereira H., Crespo J.P.S.G., Moura M.J., Carrondo M.J.T., Xavier A.V. 1989. In
vivo NMR studies of propionic-acid fermentation by Propionibacterium acidi -
propionici dans J.A.M. De Bont , J. Visser, B. Mattiasson, et J. Tramper, eds.
Physiology of immobilized cells. Elservier Science Publishers, Amsterdam, The
Netherlands.
SAS/STAT® (1989) User's guide. SAS Inst. Inc., Cary, NC, USA.
Sebastiani H., Zelger G. (1998) Texture formation by thermophilic lactic acid bacteria.
Milchwissen 53: 15-20.
Senthuran A., Senthuran V., Mattiasson B., Kaul R. (1997) Lactic acid fermentation in a
recycle batch reactor using immobilized Lactobacillus casei. Biotechnol Bioeng 55:
841-853.
Smith M.R., van der Schaaf A., de Ree E.M., de Bont J.A.M., Hugenholtz J. (1993) The
physiology of Lactococcus lactis subsp. lactis biovar. diacetylactis immobilized in
hollow-fibre bioreactors: glucose, lactose and citrate metabolism et high cell
densities. Appl Microbiol Biotechnol 39: 94-98.
Stanley P.E. (1986) Extraction of adenosine triphosphate from microbial and somatic cells.
Methods Enzymol 133: 14-22.
Stingele F., Nesser J.-R., Mollet B. (1996) Identification and characterization of the eps
(exopolysaccharide) gene cluster from Streptococcus thermophilus Sfi6. J Bacteriol
178: 1680-1690.
Sutherland I.W. 1972. Bacterial exopolysaccharides dans A.H. Rose, ed. Advances in
Microbial Physiology. Academic Press, New York, NY, USA.
146Sutherland I.W. 1982. Biosynthesis of microbial exopolysaccharides. Pages 80-150
dans A.H.R.a.J.G. Morris, ed. Advances in Microbial Physiology. Academic Press,
New York, USA.
Sutherland I.W. (1990) Biotechnology of microbial exopolysaccarides. Cambridge
University Press, Cambridge, UK.
Sutherland I.W. (1998) Novel and established applications of microbial polysaccharides.
Trends Biotechnol 16: 41-46.
Szajani B., Buzas Z., Dallmann K., Gimesi I., Krisch J., Toth M. (1996) Continuous
production of ethanol using yeast cells immobilized in preformed cellulose beads.
Appl Microbiol Biotechnol 46: 122-125.
Taipa M.A., Cabral J.M.S., Santos H. 1989. Application of in vivo 31P-NMR to compare
the metabolism of free and gel entrapped yeast cells dans J.A.M. De Bont , J.
Visser, B. Mattiasson, et J. Tramper, eds. Physiology of immobilized cells. Elsevier
Science Publishers, Amsterdam, The Netherlands.
Tandon H.L.S., Cescas M.P., Tyner E.H. (1968) An acid-free vanadate-molybdate reagent
for the determination of total phosphorus in soils. Soil Sci. Soc. Am. Proc. 32.
Teixeira de Mattos M.J., de Boer J.P., Zoutberg G.R., Neijssel O.M. (1994) Metabolic shift
analysis at high cell densities. FEMS Microbiol Rev 14: 21-28.
Toba T., Uemura H., Itoh T. (1992) A new method for the quantitative determination of
microbial extracellular polysaccharide production using a disposable ultrafilter
membrane unit. Lett Appl Microbiol 14: 30-32.
Torino M.I., Sesma F., Font de Valdez G. (2000) Semi-defined media for the
exopolysaccharide (EPS) production by Lactobacillus helveticus ATCC 15807 and
evaluation of the components interfering with the EPS quantification. Milchwissen
35: 314-316.
Trauth E., Lemaitre J.-P., Rojas C., Diviès C., Cachon R. (2001) Resistance of immobilized
lactic acid bacteria to the inhibitory effect of quartenary ammonium sanitizers.
Lebensm Wiss Technol 34: 239 - 243.
Tuinier R., Zoon P., Cohen Stuart M.A., Fleer G.J., de Kruif C.G. (1999a) Concentration
and shear-rate dependence of the viscosity of an exocellular polysaccharide.
Biopolymers 50: 641-646.
147Tuinier R., Zoon P., Olieman C., Cohen Stuart M.A., Fleer G.J., de Kruif C.G. (1999b)
Isolation and physical characterization of an exocellular polysaccharide.
Biopolymers 49: 1-9.
Valyasevi R., Sandine W.E., Geller B.L. (1994) Lactococcus lactis subsp. lactis C2
bacteriophage sk1 involves rhamnose and glucose moieties in the cell wall. J Dairy
Sci 77: 1-6.
Van Calsteren M.R., Pau-Roblot C., Begin A., Roy D. (2002) Structure determination of
the exopolysaccharide produced by Lactobacillus rhamnosus strains RW-9595M
and R. Biochem J 363: 7-17.
Van Casteren W.H.M., Dijkema C., Schols H.A., Beldman G., Voragen A.G.J. (1998)
Characterisation and modification of the exopolysaccharide produced by
Lactococcus lactis subsp. cremoris B40. Carbo Poly 37: 123-130.
van den Berg D.J.C., Robijn G.W., Janssen A.C., Guiseppin M.L.F., Vreeker R., Kamerling
J.P., Vliegenthart J.F.G., Ledeboer A.M., Verrips C.T. (1995) Production of a novel
extracellular polysaccharide by Lactobacillus sake 0-1 and characterization of the
polysaccharide. Appl Environ Microbiol 61: 2840-2844.
van Dijken J.P., Harder W. (1975) Growth yields of microorganisms on methanol and
methane A theoretical study. Biotechnol Bioeng 17: 15-30.
van Kranenburg R., Kleerebezem M., de Vos W.M. (2000) Nucleotide sequence analysis of
the lactococcal EPS plasmid pNZ4000. Plasmid 43: 130-136.
Van Kranenburg R., Marugg J.D., Van Swan I.I., Willem N.J., De Vos W.M. (1997)
Molecular characterization of the plasmid-encoded eps gene cluster essential for
exopolysaccharide biosynthesis in Lactococcus lactis. Molecular Microbiology 24:
387-397.
Van Kranenburg R., Van Swan I.I., Kleerebezem M., De Vos W.M. (1998) Expression,
disruption , and complementation of eps genes essential for exopolysaccharide
biosynthesis in L. lactis. Pages 45-46. ASM Conference on Streptococcal Genetics,
Vichy, France.
Velazquez A.C., Pometto A.L., 3rd, Ho K.L., Demirci A. (2001) Evaluation of plastic-
composite supports in repeated fed-batch biofilm lactic acid fermentation by
Lactobacillus casei. Appl Microbiol Biotechnol 55: 434-441.
148Wacher-Rodarte C., Galvan M.V., Farrés A., Gallardo F., Marshall V.M., Garcia-
Garibay M. (1993) Yogurt production from reconstituted skim milk powders using
different polymer and non-polymer forming starter cultures. J Dairy Res 60: 247-
254.
Wang S.-D. (1988) Fundamentals of biopolymer accumulation in immobilized
Acinetobacter calcoaceticus system. 280 pages. Thèse Ph.D. Department of applied
biological sciences. Massachusetts Institute of Technology, Cambridge, MA, USA.
Wang S.-D., Wang D.I.C. (1989) Cell adsorption and local accumulation of extracellular
polysaccharide in an immobilized Acinetobacter calcoaceticus system. Biotechnol
Bioeng 34: 1261-1267.
Webb C., Fukuda H., Atkinson B. (1986) The production of cellulase in a spouted bed
fermentor using cells immobilized in biomass support particles. Biotechnol Bioeng
28: 41-50.
Wen Z.T., Burne R.A. (2002) Functional genomics approach to identifying genes required
for biofilm development by Streptococcus mutans. Appl Environ Microbiol 68:
1196-1203.
West T.P. (2000) Exopolysaccharide production by entrapped cells of the fungus
Aureobasidium pullulans ATCC 201253. J Basic Microbiol 40: 397-401.
West T.P., Strohfus B. (1996) Polysaccharide production by sponge-immobilized cells of
the fungus Aureobasidium pullulans. Lett Appl Microbiol 22: 162-164.
West T.P., Strohfus B. (1998) Polysaccharide production by Aureobasidium pullulans cells
immobilized by entrapment. Microbiol Res 153: 253-256.
West T.P., Strohfus B. (2001) Polysaccharide production by immobilized Aureobasidium
pullulans cells in batch bioreactors. Microbiol Res 156: 285-288.
Whitfield C. (1988) Bacterial extracellular polysaccharides. Can J Microbiol 34: 415-420.
Wicken A.J., Ayres A., Campbell L.K., Knox K.W. (1983) Effect of growth conditions on
production of rhamnose-containing cell wall and capsular polysaccharides by strains
of Lactobacillus casei subsp. rhamnosus. J Bacteriol 153: 84-92.
Willaert R.G., Baron G.V. (1996) Gel entrapment and micro-encapsulation: Methods,
applications and engineering principles. Rev Chem Eng 12.
149Yang Z., Huttunen E., Staaf M., Widmalm G., Tenhu H. (1999) Separation, purification
and characterisation of extracellular polysaccharides produced by slime- forming
Lactococcus lactis ssp. cremoris strains. Int Dairy J 9: 631-638.
Zubillaga M., Weill R., Postaire E., Goldman C., Caro R., Boccio J. (2001) Effect of
probiotics and functional foods and their use in different diseases. Nutrition Res 21:
569-579.
Annexe 1 Concentration en ATP pendant une
fermentation avec des cellules libres de Lb. rhamnosus
RW-9595M
Annexe 2 Cell counts and lactic acid, soluble EPS and
immobilized cell concentration during a 32 day
continuous culture in a two stage bioreactor system. Variables Responses
Cell counts Lactic acid conc. EPS conc. Immobilized
ICB FCB ICB FCB ICB FCB Cell conc.
age stop (CFU/ml) (CFU/ml) (g/L) (g/L) (mg/L) (mg/L) (CFU/ml)
000 1 0 1,19E+09 1,09E+09 4,0 5,2 118,81 -58,15 2,86·1011
0+0 2 0 3,25E+08 6,63E+08 4,4 5,8 21,13 69,83 2,88·1011
000 4 0 1,01E+09 1,74E+09 7,5 13,9 55,31 161,87 3,03·1011
-++ 5 0 4,05E+08 1,29E+09 4,5 10,8 37,93 27,31 3,31·1011
00- 6 0 4,50E+09 8,65E+09 15,7 27,2 58,00 395,46 2,59·1011
000 7 0 2,67E+09 3,77E+09 9,0 14,5 51,01 274,93 4,90·1011
--- 8 0 1,40E+08 4,30E+08 8,0 16,6 55,49 211,72 4,60·1011
00+ 9 0 1,61E+09 3,03E+09 5,5 12,0 60,79 52,97 4,39·1011
+++ 10 0 1,02E+09 4,37E+09 7,1 19,8 -20,49 40,45 2,68·1011
-+- 11 0 1,71E+09 3,40E+09 15,5 29,7 175,58 7,89 4,04·1011
000 12 1 1,25E+09 6,00E+09 10,3 38,7 396,75 122,63 6,04·1011
+-+ 13 1 6,30E+08 9,90E+08 6,9 30,5 165,84 -131,23 3,84·1011
000 14 1 1,33E+09 1,70E+09 13,1 40,0 103,57 17,92 4,74·1011
--+ 15 1 9,15E+08 8,15E+08 7,7 26,0 99,16 27,76 3,57·1011
000 16 1 1,40E+09 1,60E+09 14,9 42,8 107,37 -234,99 2,77·1011
-00 17 1 6,12E+08 7,65E+08 9,3 33,6 119,17 27,78 2,06·1011
+00 18 1 1,16E+09 1,48E+09 19,3 48,9 46,33 8,97 3,26·1011
000 19 1 1,37E+09 1,23E+09 19,2 34,4 172,11 -100,58 4,18·1011
+-- 20 1 2,10E+09 2,87E+09 27,8 49,8 269,29 -181,09 1,58·1011
0-0 21 1 1,10E+09 1,22E+09 17,3 33,7 101,40 36,07 3,65·1011
000 22 1 1,38E+09 1,19E+09 27,4 51,4 15,88 80,21 6,27·1011
++- 23 1 2,17E+09 2,47E+09 38,1 51,0 163,72 -84,32 2,18·1011
000 24 1 1,25E+09 1,15E+09 22,9 43,5 105,25 -70,79 5,34·1011
Annexe 3 Analysis of variance and parameter estimates
for lactic acid concentration in the effluent of the ICB
and the FCB. ICB FCB
d Estimate SS d Estimate SS
Model 11 1688.5*** 12 4733.2***
Intercept -1.432 9.410
Covariates stop 1 3.091 29.110* 1 -6.038 90.890*
age 1 1.261 361.606*** 1 2.374 124.757*
age*age - 1 -0.048 47.221
Linear YE 1 2.725 89.539*** 1 3.021 102.267
T 1 1.415 18.233 1 2.838 73.342*
D 1 -4.593 271.110*** 1 -5.675 394.532***
Quadratic YE*YE 1 -0.859 10.638 1 -0.197 0.509
T*T 1 -0.489 3.671 1 -2.058 63.335
D*D 1 0.111 0.126 1 0.587 2.688
Cross-product T*YE 1 -0.313 0.764 1 -1.769 24.383
D*YE 1 -3.339 71.203** 1 -0.258 0.307
D*T 1 -1.142 8.208 1 0.872 4.692
Error 11 47.552 10 169.220
Total 22 658.883 22 1098.143
Adjusted R2 0.94 0.92
R2 0.97 0.96
Significance levels: ***P<0.001; **P<0.01; *P<0.05
Top Related