CERTIFICAT D'ASSEMBLAGE - Amazon S3 · USA 0.4400 0.6800 0.007 0.0270 0.2000 0.1100 0.0800 0.1900...
Transcript of CERTIFICAT D'ASSEMBLAGE - Amazon S3 · USA 0.4400 0.6800 0.007 0.0270 0.2000 0.1100 0.0800 0.1900...
12770 Rue Brault,
Mirabel QC, J7J 1P3Sans Frais / Toll Free 1 888 657.2203
Tel. : 450 420.1839 Fax : 450 420.3882
www.boulonsplus.net
CERTIFICAT D'ASSEMBLAGEASSEMBLY CERTIFICATE
SVP PRENDRE NOTE QUE L'ASSEMBLAGE SUIVANT A ÉTÉ PRODUIT PAR BOULONS PLUS
INC. ET NOMMÉ D'APRÈS LE NUMÉRO DE D'ASSEMBLAGE DU BOULON, DE L'ÉCROU AINSI
QUE DE LA RONDELLE.
PLEASE TAKE NOTE THAT THE FOLLOWING ASSEMBLY WAS DONE BY BOULONS PLUS INC.
AND NAMED AFTER THE SET NUMBER MADE FROM THE BOLT, THE NUT AND THE WASHER.
Sylvain Vaudry, Assurance-Qualité / Authorized test Clerk
PLACAGE / GALVANISATION #
PLATING / GALVANISATION #
SET #
BOULON / BOLT LOT #
ÉCROU / NUT LOT #
RONDELLE / WASHER LOT #
L’ANALYSE CHIMIQUE PROVIENT DU FOURNISSEUR D’ACIER.
ESSAIE DE CAPACITÉ ROTATIVE AVEC INDICATEUR DE TENSION. RÉSULTAT D’ESSAI = ACCEPTÉ.
L’ASSEMBLÉE RENCONTRE LES EXIGENCES DE LA NORME ASTM A325.
-- ÉCROUS LUBRIFIÉS.
CHEMICAL ANALYSIS COMES FROM THE STEEL COMPANY.
RC TEST DONE WITH TENSION MEASURING DEVICE. ROTATIONAL CAPACITY TEST = PASSED
ASSEMBLY MEETS THE REQUIREMENTS OF THE ASTM A325 STANDARD.
- NUTS LUBRICATED.
20722-030516
JX672-01
22514-6214022904
D0278
1-8 X 2 3/4 A325-1 USA SETBLT+A563-C+F436-1 PL
MNPCOR
UNYTIT
PRESTA
TEST CERTIFICATECertificate #0107-02Mechanical Testing
Date Printed: 08/28/2015
Customer: Manufacturer:44225 Utica RoadUtica, MI 48318Tel:(586) 254-1320Fax:(586) 726-5668 BOULONS PLUS
Destination per Shipper No.160530
MNP Corporation44225 Utica RoadUtica, MI 48318
Report Number MNP-1275608-1Part Number:Eng. Change:
Lot Number:Purchase Order:
Lot Size:Nominal Length:
Nominal Thread Diameter:Material Heat:
Washer Material Lot:Safety Lot Number:
BP1001-275-A325N/AJX672-014274046,8782.751 in10366790N/A N/A N/AN/A
Family: BoltClass: 2A
Thread: 8/inDrive: Hex
Dimensional STD: PER PART PRINT
QA STD: QAS Per ISO/TS 16949,ISO 9000,ASME B18.18.6M
Mechanical Property STD: ASTM A325Plating/Finish STD: N/A
Patch STD: N/AMaterial Spec: 1039M-C
Chemical Composition:
MFG ID Marking
C0.41
Mn0.94
P0.009
S0.009
Si0.21
Cu0.09
Ni0.05
Cr0.32
Mo0.02
Al0.002
B0.0001
Analysis Performed by:CHARTER STEELLab Id:
Feature Checked# of
SamplesSpecification
Min/MaxUnits ofMeasure Results Method of Test
InspectingFacility Code
InspectingFacility Name
200160-0
Date Manufactured: 07/01/2015
Corporation
Part Description: 1000,8,2750 STRUCTURAL BOLT
Surface Discontinuities 1 Visual Pass SAE J1061 0107-02 MNPForming Quality 1 Visual Pass Per above Standard 0107-02 MNPRouting Sequence 1 Visual Pass Per above Standard 0107-02 MNPGrade and Source ID 1 Visual Pass Per above MFG ID 0107-02 MNPThread Acceptability 1 Pass Per above Standard 0107-02 MNPCore Hardness 15 25 34 HRC 29.3 - 30.2 JX672-01 0107-02 MNPSurface Hardness 15 72 77 15N 74.6 - 75.7 JX672-01 0107-02 MNPProof Load 1 51500 N/A Lbs. Pass Per above Standard 0107-02 MNP10 Degree Wedge Tensile 11 72700 N/A Lbs. 79748 - 81078 JX672-01 0107-02 MNP
* per Source Control Plan
Manufactured in the USA
THIS REPORT IS NOT TO BE REPRODUCED EXCEPT IN FULL.Dimensional inspections performed per Manufacturing ControlIndividual test results available upon request.Product conforms to standard specified.Data shown applies only to parts tested.
Name:Title:Signed:
Terri SimpsonAuditor
The A2LA accreditation logo and certificate number applies to MNP
Page: 1 of 1
Unytite, Inc.
One Unytite Drive
Peru, IL 61354
Tel 815-224-2221
Fax 815-224-3434
INSPECTION CERTIFICATE
Job No: 22514 Job Information Certified Date: 2/17/16
Customer: Ship To:
Customer PO No: Shipped Qty:
Lot Number: 22514-6214022904
Part Information
Part No: A563 1-8 DH HHN
Description: ASTM A563 Heavy Hex Nut, Grade DH, Plain
Manufactured Quantity: 54,775
Applicable Specifications
Specification Amend Specification Amend
ASME B1.1 2008 ASME B18.2.2 2010
ASTM A563 2007 ASTM F606/606M 2014
ASTM F812/F812M 2012
Test Results Test No: 10356 Test: A563 DH Mechanical Properties
Description Hardness
(HRC) Tempering Temp (800
degree F Min) Proof Load (Pass/Fail)
(ASTM Min) Shape & Dimension
ASME B18.2.2 Thread Precision
ASME B18.1.1 Visual ASTM
F812
Sample
Inspection 27.6 1,193 106,050 Pass Pass Pass
Certified Chemical Analysis Heat No Grade Manufacturer Origin C Mn P S Si Cr Ni Cu
6214022904 1045 Gerdau
Ameristeel USA 0.4400 0.6800 0.007 0.0270 0.2000 0.1100 0.0800 0.1900
Notes All tests are in accordance with the latest revisions of the methods prescribed in the applicable SAE and ASTM Specifications. The samples tested conform the specifications as described/listed above and were manufactured free of mercury contamination and there is no welding
performed in the production of the products. No heats to which Bismuth, Selenium, Tellurium, or Lead was intentionally added have been used to produce products. The steel was melted and manufactured in the U.S.A. and the product was manufactured and tested in the U.S.A.
We certify that this data is true representation of information provided by the material supplier and our testing laboratory. This certified material test report relates only to the items listed on this document and may not be reproduced except in full.
Sobkowiak, Bill - Supervisor, Quality
2/17/16
Date
Plex 2/17/16 12:00 PM bsobkowiak Page 1