SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION...

12
SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE Instructions, drawings, and diagrams contained in this manual present information available at the time of printing. Although every attempt has been made to keep them up-to-date, Kohler Company reserves the right to implement product changes without further notice. CAUTION It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws. Page 1 Kohler Co. 1089610 - C May 2009

Transcript of SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION...

Page 1: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR

INSTALLATION GUIDE

Instructions, drawings, and diagrams contained in this manual present information available at the time of printing. Although every attempt has been made to keep them up-to-date, Kohler

Company reserves the right to implement product changes without further notice.

CAUTIONIt is the responsibility of the INSTALLER to ensure that the

installation complies with council and or local authority bylaws.

Page 1 Kohler Co.1089610 - C May 2009

Page 2: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

Tools Required.

Philips Screwdriver.Pencil.Silicone gun.Measuring tape.Safety glasses.Center punch.Hammer.Knife.Drill bits. 1 x 6mm. 1 x 2.5mm.Level.

Materials Required.

Drop cloth.SIKA Silaflex NG silicone sealant.

Before you install your shower door, please read these instructions carefully to familiarise yourself with the required tools, materials and installation sequences.

These instructions contain important care and cleaning information. Please leave these for the consumer after installation.

Make sure that the shower tray and the wall are completely finished prior to installing your SAPPHIRE shower door.

CAUTION: Risk of injury or product damage.Tempered glass cannot be cut.

CAUTION: Before commencing installation.KOHLER strongly recommends reading these installation instructions.

ATTENTION: Please install this door on an ENGLEFIELD Quick-Fit® shower tray only.

IMPORTANT: The shower door requires a flat and vertical wall surface. The flatness is recommended to be out by no more than 4mm / m.

BEFORE YOU BEGIN

TOOLS AND MATERIALS REQUIRED

Page 2 Kohler Co.1089610 - C May 2009

Page 3: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

2005/2/25 13

Elevation

Top rail

Bottom rail

Plan view

46.5

mm

25mm

B

1830

mm

A

B

A

SIZE DIMENSION ‘A’ DIMENSION ‘B’900 x 900 872 ± 7.5mm 872 ± 7.5mm1000 x 1000 972 ± 7.5mm 972 ± 7.5mm 1200 x 900 872 ± 7.5mm 1161 ± 7.5mm

Page 3 Kohler Co.1089610 - C May 2009

ROUGH-IN

MAX. DOOR OPENING480mm500mm 480mm

Page 4: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

PARTS IDENTIFICATION

Page 4 Kohler Co.1089610 - C May 2009

PARTS IDENTIFICATION

Corner cover, top left

Screw cover

Top and bottom rail seal*

Door entry seal

Door Seal

Wedge

Door Handle*

Top and bottom rail

Stopper Screw

Left door stop

Infill glass

Right door stop

Corner cover clip

ST 3.9 X 12 mm

Clip screw

Corner cover top right

ST 4.2 X 9.5 mm

Corner cover clip

Wall retainer seal

Corner cover bottom right

ST 4.2 X 16 mm Infill glass screw

Corner cover bottom left

Top roller sets*

Bottom roller sets*

Door edge cap Magnetic seal

Return seal

Door panel assy right

Door panel assy left.

Wall anchor

Wall retainer screw ST 4.2 x 28mm

Wall retainer

Page 5: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

SIZE DIMENSION ‘C’900 x 900 862mm

1200 x 900 1154mm 1000 x 1000 967mm

1. Mark and drill wall retainer fixing holes

Wall retainer screw.

ST 4.2 x 28 mm

B

Measure and mark a line on the rim of the tray using the following dimensions (all dimensions are measured from the acrylic wall face):

Align the outside face of the wall retainer with the mark on the rim of the tray.

Using a level, plumb the wall retainer, and mark the three mounting holes with a pencil.

Use a 6mm drill bit to drill the holes.

Press fit the wall anchors into the holes.

Repeat this procedure for the other wall retainer. Shower Tray

Wall retainer

Pencil

Level

Inside oftray

Outsideof tray

CD

2. Install the wall retainers.

Install each wall retainer by aligning the holes in the retainer with the wall anchors.

Secure the wall retainers wth 6 x ST 4.2 x 28 mm screws provided.

Page 5 Kohler Co.1089610 - C May 2009

DOOR INSTALLATION

DIMENSION ‘D’862mm

862mm 967mm

right hand tray shown

Page 6: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

4. Install the infill glass

B

Press fit the infill glass to the bottom rail.

Note: Make sure that the fixing holes in the glass align with the holes in the bottom rail.

3. Install the bottom rail.

Press fit the bottom rail into the wall retainer on the tray.

Note: Make sure there are seals in each end of the top and bottom rails,and the end of the seal aligns with Rail

Seal

the end of the rail.

B

Page 6 Kohler Co.1089610 - C May 2009

Page 7: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

B

B

1830 mm

5. Install the top rail.

Press fit the top rail to the top end of both glass infill panels.

Make sure that the glass infill panels align with the end of the rails.

6. Adjust the top rail.

To make sure that the rails are correctly fitted to the glass infill panels, use a tape measure to make sure the total height of the assembled product is 1830 mm.

If higher, try pressing the top rail onto the glass infill panels harder.

If lower, insert a wedge into the gap between the glass infill panels and the top rail seal.

1830 mm

1830 mm

Page 7 Kohler Co.1089610 - C May 2009

Page 8: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

ST 4.2 x 16 mm

ST 4.2 x 16 mm

7. Fix the top and bottom rails to the glass infill panels.

Use a power drill on a low torque setting to drive the countersunk screws into the top and bottom rails - 8 places.

Take care not to over drive these screws.

8. Install the wall retainer seals

Press fit the wall retainer seals into the wall retainer.

Soft edge of retainer seal

Page 8 Kohler Co.1089610 - C May 2009

Ensure the seals are fitted with the soft edge in contact with the face of the glass, as show in the illustration on the right hand side.

Page 9: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

B

9.

Notch 3-5mm of rigid portion at bottom

the sill extrusion (right hand seal shown).

Sill extrusion

Return panel

Return seal

Return seal

(right hand)

Flexible flap

of seals so that the flexible flap overlaps

a) Referring to the diagram below, cut the return seals to the length leaving a 3 - 5mm notch at the bottom so that the fexible flap overlaps the curved still extrusion.

b) Press fit the return seals onto the vertical edges of both return panels. The flexible flap should point inside shower.

C

A

D

10. Install the door panels.

Identify the left door from the right door, referring to the handle location. Note that the rollers on the top edge are height adjustable.

A) From the inside of the shower, hang the door panel on the top rail.

B) Press the button on the bottom rollers and fit the rollers into the bottom rail.

C) If there are gaps between the doors, raise or lower the doors by adjusting the screws in the top rollers (clockwise to raise the door). Once done there should be no gaps between the doors, and the top edges must be level.

D) Press fit the door seals onto the vertical edges of both doors.

Page 9 Kohler Co.1089610 - C May 2009

Page 10: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

ST 4.2 x 9.5mm

ST 4.2 x 9.5mm

ST 4.2 x 9.5mm

11. Install the corner cover clips.

Move the bottom rail forward or backward to make sure that the gap between the bottom rail and the front edge of the tray is even.

Make sure that the edges of the infill glass are vertical.

Drill a 2.5mm hole through the small holes at the top and bottom ends of the retainers, and into the top and bottom rail.

Take care to not drill all the way through the retainers!

Fix the corner cover clips to the retainer. Make sure that the pin on the back of the clip aligns with the large hole at the top and bottom end of the retainer.

Apply silicone along the broken line

12. Sealing the door.

CAUTION: Use only Sika Silaflex NG Silicone Sealant.

CAUTION: Apply silicone to the outside of the door only. silicone applied to the inside of the door will cause leakage and damage.

Thoroughly clean all surfaces. Remove all dust, dirt or grease from the bottom rail, retainers and shower tray.

For best results apply masking tape to within 5mm of the joints to be sealed.

Apply a bead of sealant around the outside of the door where:

1. The bottom rail meets the tray.

2. The retainers meet the wall and the tray.

3. In and around the bottom corners where the retainers meet the bottom rail, and behind the corner cover caps.

NOTE: Allow silicone to cure for 24 hours before using shower.

Page 10 Kohler Co.1089610 - C May 2009

Page 11: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

13. Fit door entry seals and corner covers.

Press fit the door entry seals into the channel in the top side of the bottom rail, and the underside of the top rail.

Press fit all four corner covers over the corner cover clips.

Page 11 Kohler Co.1089610 - C May 2009

Page 12: SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR...SAPPHIRE ROUND CORNER SLIDING SHOWER DOOR INSTALLATION GUIDE ... the sill extrusion (right hand seal shown). Sill extrusion Return panel

Use non abrasive soap and water when ever possible.In addition you may safely use:• Mr Muscle Shower Clean (branded as Windex Shower Clean in Australia).• Jif Powerspray.

Avoid:• harsh chemicals and disinfectants.• abrasive cleaners.• solvent based cleaners.• acid or alkaline cleaners.• products containing ammonia or peroxides.

Wipe out the unit after each use to prevent build-up of scum.

Always read the label instructions on any cleaner carefully before applying it to the surface.

Use a squeegee or dry towel to dry the glass after use.

Regularly wash down the extrusions with warm water and mild soap solution.Where greasy deposits are concerned, cleaning may require a soft cloth dipped in white spirits.Thoroughly rinse with water after cleaning to ensure removal of all residues.

Page 12 Kohler Co.1089610 - C May 2009

CLEANING INSTRUCTIONS

NEW ZEALANDKOHLER NZ Ltd.Ph 0800 100 382Fax 0800 664 488www.englefield.co.nz

CALL US FOR HELP

AUSTRALIAKOHLER Co.Ph 1300 362 284Fax 1300 652 284www.englefield.com